• 한국도로학회지:도로
• /
• v.1 no.1
• /
• pp.31-35
• /
• 1999

• 한국도로학회지:도로
• /
• v.2 no.2
• /
• pp.74-80
• /
• 2000

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.9
• /
• pp.4199-4204
• /
• 2011

The dynamic modulus of hot mix asphalt is one of the important indicators to evaluate the durability and performance of asphalt pavement. In resent, the dynamic modulus is suggested by a key property of asphalt pavement design and analysis in AASHTO 2002 Design Guide and Korean Pavement Research Project(KPRP). Master curve from laboratory test results should be needed for pavement design and analysis. The process to get the master curve is standardized. But, there are some setup and testing error at low temperature(-$10^{\circ}C$) and high temperature ($55^{\circ}C$). In this paper, a simplified process which is used 3 testing temperatures (5, 21, 40) is adopted to get the master curve. Comparison was carried out for standard process and simplified process. The suggested process can be used to get the master curve of asphalt pavement, even though some difference was shown at high temperature.

• International Journal of Highway Engineering
• /
• v.10 no.4
• /
• pp.269-279
• /
• 2008

This study was conducted to develop the design methodology of transverse post-tensioning for the prestressed concrete pavement (PSCP). The transverse stress distribution was analyzed when the transverse anchor spacing changed. The tensile stress distribution in the PSCP slab due to the environmental and vehicle loads was also investigated. The reasonable methods were discussed to determine the design loads including environmental and vehicle loads and the PSCP allowable tensile stress used for the basis of the selection of the stress application amount from the tensioning. The results of this study showed that as the transverse anchor spacing increased, the range of the stress loss became larger and the stress loss was significant near the shoulder. The design of the transverse post-tensioning can be performed by obtaining the stresses under the design loads and by considering the allowable tensile stress; however, the tensile stresses at different locations such as the shoulder, wheel pass, and slab interior should also be checked and kept below the allowable tensile stress.

• International Journal of Highway Engineering
• /
• v.12 no.3
• /
• pp.147-154
• /
• 2010

In post-tensioned concrete pavement(PTCP), one of the most important design variables is the initial joint width, in addition to the tensioning spacing. The joint width between PTCP slabs directly affects noise and ride quality. If the joint width is too wide, noise increases and ride quality decreases. If the initial joint width is too narrow, on the other hand, under high temperature, PTCP slabs can blow up, or failures near the joint can occur due to excessive compressive stresses. This study was conducted to determine the optimal initial joint width of PTCP and to investigate the joint width behavior under temperature changes. The experiments were performed using one-year-old PTCP slabs. The concrete temperatures were measured using the temperature measurement sensors installed at various depths. The joint widths were measured using vernier-calipers at different times of a day and the relationship between the joint width and temperature was analyzed. From this study, the design methodology to determine the optimal initial joint width of PTCP could be proposed.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.13 no.1 s.53
• /
• pp.106-114
• /
• 2009

The steel design based on the width of transverse crack which is the major factor to affect a long-term performance of continuously reinforced concrete pavement was developed. For this study, twenty-one cities of Texas were selected and the temperature data was collected at those locations during the past ten years. From the data, zero-stress temperatures were calculated by the PavePro program and the widths of transverse crack were analyzed by the CRCP program. The variables used to this numerical analysis were slab thickness, coefficient of thermal expansion of concrete, steel ratio, and design temperature. The total of 448 factorial runs were made and the regression analysis was performed using the results. Steel ratios from the regression equations were backcalculated and a steel design table was proposed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.17-18
• /
• 2010

This study was conducted to develop the design guide of PTCP (Post Tensioned Concrete Pavement). The behavior of PTCP was investigated by performing structural analyses and field experiments. Based on the results, the PTCP design guide was developed by determining the size of concrete slab, design environmental and vehicle loads, and amount and method of longitudinal and transverse tensioning.

• Journal of Pharmaceutical Investigation
• /
• v.13 no.3
• /
• pp.115-125
• /
• 1983

제제설계란 제형의 설계 및 그에 따른 처방설정(formulation)을 의미하며 경험적인 제제방법 및 그 기술측면에서의 제제화는 주악 및 첨가물의 종류와 배합비율의 설정등 비교적 단순한 내용을 의미하지만 의약품은 실제적으로 인체에 적용되므로 치료설계상의 연구와 생물약제학적 검토에 의한 유효정과 안전성을 발휘할 수 있도록 설계가 되어야 한다. 또한 약물의 효력은 체내 특정부위에 특정농도의 약물분포가 필요하고, 일정시간 지속되는 것이 요구되므로 약용량도 중요하지만 약물투여 후의 흡수, 체내이행, 대사, 배설등의 상태를 파악하고 이에 미치는 부형제의 영향도 검토하여야 한다. 제제물리학적 측면에서 품질보증을 위하여 preformulation단계에서 주약의 물성검토, 첨가제의 사용량, interaction 및 혼합순서 등과 처방설정 단계에서 제제화에 사용되는 기계장치의 특성 및 능력, 제제화 후의 포장용기 및 포장상태에서의 안정성 등도 면밀히 검토하여야한다. 제제설계란 단순한 dosage form의 design만이 아니고 유효성이 높고, 부작용이 적은 제제를 합리적으로 만드는 기술과 정보의 종합관리로 scale up과정에서 원료, 기계장치, 제조방법, 작업자 등에 의한 품질변동 요인을 극소화하고, 공정의 초기단계에서 즉시 조정될 수 있는 종합관리 system이 필요하다.

• International Journal of Highway Engineering
• /
• v.10 no.2
• /
• pp.1-13
• /
• 2008

This study presents a case study of condition evaluation of various asphalt pavement sections to estimate performance lives. The pavement surface conditions including cracking and rutting are first evaluated using a automatic pavement analyzer, ARAN. HPCI(Highway Pavement Condition Index) values are estimated using the pavement surface distress data. It is observed from the pavement distress survey that the major distress type of the sections is top-down cracking. The modulus value of each pavement layer is back-calculated from the defection data obtained from a FWD(Falling Weight Deflectometer) and compared with the laboratory measured dynamic modulus values. Remaining lives of the various pavement sections are estimated based on a mechanistic-empirical approach and AAHTO 1993 design guide. The structural capacities of the all pavement sections based on the two approaches are strong enough to maintain the pavement sections for the rest of design life. Since the major distress type is top-down cracking, the remaining lives of the pavement sections are estimated based on HPCI and existing performance database of highway pavements. To evaluate the causes of premature pavement distress, various material properties, such as air void, asphalt binder content, aggregate gradation, dynamic modulus and fatigue resistance, are measured from the field cores. It is impossible to accurately estimate the binder contents of field samples using the ignition method. It is concluded from the laboratory tests that the premature top down cracking is mainly due to insufficient compaction and inadequate aggregate gradation.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.11
• /
• pp.314-321
• /
• 2016

Adapting the maintenance criteria of Seoul City pavement is not applicable for borough pavement due to differences between the pavement of Seoul city and the borough, such as priority of maintenance, traffic volume, thickness of pavement, and pavement deterioration rate by distresses. To develop an efficient and reasonable evaluation method of the Seocho borough pavement condition within a limited budget, this study suggested the borough pavement condition evaluation model based on the PMS (Pavement Management System) of Seoul Metropolitan SPI (Seoul Pavement Index). The SPI was modified to predict the remaining life and determine the proper maintenance method for the pavement in Seocho borough. This was suggested to reflect the rate of the designed performance life and field performance life of pavement as well as the pavement condition at the stage of the completion of construction. Primary variables, such as crack, rutting and IRI in the final model affect the overall performance life due to their even composition. Therefore, the suggested model considering the lowered criteria, design performance factor, and construction factor can be used for the more efficient maintenance of Seocho borough pavement.