• Proceedings of the KAIS Fall Conference
• /
• 2001.05a
• /
• pp.47-48
• /
• 2001

본 연구의 목적은 폐 구리염화물 용액을 원료로 사용하여 분무열분해 공정에 의해 평균입도가 1㎛이하이며 입도분포가 균일하고 치밀한 조직을 나타내는 미립의 구리산화물 분말을 제조하는데 있다. 또한 본 연구에서는 분무열분해 공정에 의해 생성되는 분말의 특성에 영향을 미치는 반응 온도, 원료용액의 유입속도, 분위기 기체 및 공기의 유입속도, nezzle tip 크기 및 원료용액의 농도 등의 반응인자들의 영향을 검토하였다.

• Journal of Chest Surgery
• /
• v.34 no.2
• /
• pp.180-183
• /
• 2001

Oncocytic carcinoid는 매우 드문 종양으로 단지 몇 례만이 문헌상 보고되고 있다. 본 저자들은 좌폐 상엽에 발생한 oncocytic carcinoid 1례를 치험하였는데 환자는 56세된 여자환로 특이한 증상은 없었다. 흉부 전산화 단층촬영상 좌폐상엽에 3$\times$3.5 cm 크기의 동종의 종괴를 보이고 있었다. 수술전 검사후 외과적절제술을 시행하였는데 육안적소견상 4$\times$3cm 크기의 경계가 명확한 황갈색의 종괴였으며, 병리조직학적 검사상 괴립성 호산성 세포질이 풍부한 양상을 보였으며 면역조직학적 검사에서는 cytokeratin에 양성반응을 보였으며 EMA와 chromograin에 국소적인 양성반응을 보여, 폐에 발생한 oncocytic carcinoid로 진단하였다. 수술후 환자의 상태는 양호하였으며, 현재 외래추적관찰중이다.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2005.10a
• /
• pp.308-313
• /
• 2005

실리콘 잉고트의 절단공정에서 발생하는 폐실리콘 슬러지는 실리콘과 실리콘카바이드 등의 유가자원이 함유되어 있으며, 이 중 실리콘 분말은 실리콘 화합물인 알콕시실란 등을 제조하는데 원료로 사용이 가능하다. 본 연구에서는 폐실리콘 슬러지로부터 분리, 합성된 사에 톡시실란(TEOS)을 원료로 이용하여 실리카 나노분말을 합성하였다. TEOS 원료물질을 외부 혼합형 이류체 노즐을 이용하여 미세액적으로 분무하고 화염 속으로 도입시키고 화염열분해 반응을 진행시켜 실리카 나노분말을 합성하였다. 합성된 실리카 나노입자의 특성은 투과형 전자현미경 및 BET에 의하여 입자형상 및 평균 입자크기가 분석되었다. 주요 공정변수인 분산공기의 압력, 반응가스의 조성을 변화시켜 실험한 결과 평균크기가 $9{\sim}68nm$인 실리카 나노분말을 제조하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.598-602
• /
• 2018

This study examined the characteristics of the waste catalyst used in the petroleum refinery operations. The total pore volume, specific surface area, and average pore size of the spent catalyst used in the petroleum refinery operations were 3.96cc/g, 13.81m2/g, and 1.15A, respectively. The weight loss observed in the range from $25^{\circ}C-700^{\circ}C$ for the spent catalysts using TG and DTA was approximately 23 wt. %. EDS analysis of the waste catalyst sample showed that the five major components were vanadium, nickel, manganese, iron, and copper. The extraction system is attractive for liquid-liquid extraction. In this study, Cynex 272 was used to extract vanadium from waste catalyst. The electrochemical characteristics of the extracted vanadium solution were measured by cyclic voltammetry (CV). As a result, an oxidation / reduction peak appeared, indicating the potential of an electrolytic solution.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.293-293
• /
• 2010

최근 태양전지 연구에서 저가격화를 실현하는 방법 중 하나로 폐 실리콘 웨이퍼를 재생하는 방법에 관하여 많은 연구가 진행되고 있다. 그러나 기존 웨이퍼 재생공정은 높은 재처리 비용과 복잡한 공정등의 많은 단점을 가지고 있다. 챔버 내에 압축된 공기나 가스에 의해 가속된 미세 파우더들이 재료와 충돌하면서 식각하는 기계적 건식 식각 공정 기술이라고 할 수 있는 micro blaster 공정을 이용하면 기존 재생공정보다 낮은 재처리 비용과 간단한 공정으로 재생웨이퍼를 제작할 수 있다. 하지만 이러한 micro blaster 공정은 식각 후 표면에 많은 particle과 crack을 형성시켜 태양전지용으로 사용하기에 단점을 가진다. 본 연구에서는 이러한 micro blaster를 이용한 태양전지용 재생 웨이퍼를 제작하기 위해 폐 실리콘 웨이퍼의 표면 물질을 식각하고, 식각 후 충돌에 의해 발생된 표면의 particle과 crack을 DRE(Damage Remove Etching)공정으로 제거하는 연구를 진행 하였다. 먼저 폐 실리콘 웨이퍼와 같은 표면을 형성하기 위하여 시편 표면에 각각 Al($2000{\AA}$), $Si_3N_4(3000{\AA})$, $SiO_2(1{\mu}m)$, AZ1512($1{\mu}m$)을 형성하고 micro blaster의 파우더 크기, 압력, 스캔 속도 등의 공정 조건에 따라 폐 실리콘 웨이퍼 표면 물질을 식각하였다. 식각 후 폐 실리콘 웨이퍼의 식각된 깊이와 표면 물질 잔량을 측정하고, 폐 실리콘 웨이퍼의 표면에 particle과 crack, 요철이 형성되어 있는지를 확인하였다. 그 결과 폐 실리콘 웨이퍼에 형성된 물질의 두께 이상으로 식각되었으며, 표면 물질의 잔량이 남아 있지 않았고, 표면에 많은 particle과 crack, 요철이 형성되었다. 표면에 형성된 요철은 유지하면서 많은 particle과 crack을 제거하기 위하여 micro blaster공정 후 DRE 공정으로 표면 개선이 필요하였다. 이때 남겨진 요철은 입사광량을 증가시키고, 표면 반사율을 감소시켜 태양전지내의 흡수하는 빛의 양을 증가시키는 태양전지 texturing 공정 효과로 작용하게 된다. 표면에 남은 particle과 crack을 완전히 제거하면서 요철은 유지할 수 있게 HNA 용액의 농도와 시간에 따른 식각 정도를 측정하였다. DRE 공정 후 표면 particle과 crack이 완전히 제거되어 표면이 개선됨을 확인하였다. Micro blaster를 이용하여 폐 실리콘 웨이퍼의 표면을 식각하고, DRE공정으로 표면을 개선함으로써 태양전지용 기판으로의 재생 가능성을 확인하였다.

• Clean Technology
• /
• v.12 no.4
• /
• pp.205-210
• /
• 2006

In this study, polystyrene hollow microspheres were prepared via optimized purifying steps for the reuse of waste polystyrene. PS/PVA double layered hollow microspheres were prepared using the multiple emulsion ($W_1/O/W_2$) method with recycled polystyrene. The sonication treatment at the first stage of $W_1/O$ emulsion formation was very important factor of control of particle size and its distribution. When sonication was treated for 20 seconds, the average particle size and distribution were $1.35{\mu}m$ and $0.8{\mu}m{\sim}2.8{\mu}m$, respectively. The double layered hollow microspheres that have smaller and uniformed particle size distribution were manufactured when gelatin or Tween 80 was used as surfactants in the $W_2$ phase.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.4
• /
• pp.57-66
• /
• 2013

In this study, pullout tests were carried out to evaluate pullout characteristics of waste fishing net (WFN), which added into bottom ash for recycling both bottom ash and WFN. Three different mesh size of WFN (WFN20:$20mm{\times}20mm$, WFN30:$30mm{\times}30mm$, WFN40:$40mm{\times}40mm$) and geogrid were added as a reinforcement. Pullout characteristics of waste fishing net were compared with those of the geogrid. Pullout test results showed that pullout strength and stiffness of WFN20 are a little less than those of geogrid. However, the pullout friction angle of WFN20 is similar to that of geogrid due to bearing resistance induced from transverse rib because thickness of WFN20 is greater than geogrid. Pullout test results also indicated that distribution of residual strain along reinforcement after test depends on overburden stress. Residual strain at the tip of reinforcement increased with an increase in overburden stress due to concentration of pullout force on the tip of reinforcement.

• Polymer(Korea)
• /
• v.28 no.6
• /
• pp.460-467
• /
• 2004

The polymer blends of waste poly(vinyl chloride) (RPVC) and waste polyethylene (RPE) were prepared by melt mixing. Their morphologies and rheological properties were investigated and torque changes were also measured. Comparing the torques calculated by the log additivity rule with measured torque changes, the polymer blends showed the large negative deviation behavior (NDB) due to their incompatibility. The shear viscosities of the blends decreased with increasing shear rates, showing shear thinning behavior. The shear viscosity of the blends with compatibilizer was larger than that of the blends without compatibilizer. SEM micrographs of the strands after measurement showed that the domain size of the blends was slightly enlarged with increasing the shear rate. Also, RPVC domain size was larger in the core-sections of the strands from capillary viscometer than in the surface region.

• Elastomers and Composites
• /
• v.39 no.2
• /
• pp.131-141
• /
• 2004

The recycling of waste XLPE(crosslinked polyethylene), which is a major source of scraps from high voltage power transmission cables, has been discussed. The waste XLPE scraps were ground into fine powder with various sizes from less than $100{\mu}m$ up to about $1000{\mu}m$ using two types of tailor-made pulverizers. The compounds were prepared in a modular intermeshing co-rotating twin screw extruder at various conditions such as different compositions, types and powder sizes of waste XLPE, screw configurations and various polymer matrices (LDPE, HDPE, PP, PS). The mechanical and rheological properties and the fracture surface or the compounds were investigated. It was found that an improved impact strength was obtained from the compound with white XLPE powder pulverized from the scraps without outer/inner semi-conductive layers. Generally, the impact strength increases with the content of XLPE but decreases with the size of XLPE. Especially for LDPE, the extrusion was possible up to 80 wt% loading of XLPE. Also, the impact strength increases with the number of kneading disc blocks in the given screw configurations. The melt viscosity of the compounds increases with increasing XLPE loading. However, the higher shear thinning behavior of the compounds at common shear rates implies proper processibility of the compounds. In addition, the impact strength for other polymer matrices used increases with XLPE and it is noticeable that the impact strength of PS/XLPE (80/20 wt%) compound was improved twice that of pure PS.

• Clean Technology
• /
• v.29 no.4
• /
• pp.272-278
• /
• 2023

There is a lot of interest in methods for pollutants using adsorption, and recent research is being conducted to show that biochar can be used to remove organic and inorganic pollutants. In particular, wood waste as waste biomass requires a biomass recycling method, and a method to increase the adsorption capacity of biochar produced using wood waste is needed. Biochar is created by Hydrothermal carbonization (HTC) using, which uses low temperature and high pressure, has low energy consumption and does not require moisture removal pretreatment, and biochar is created through chemical activation using KOH, NaOH, and ZnCl₂ chemicals. The adsorption characteristics of biochar were determined by analyzing iodine adsorptivity, specific surface area, pore diameter, pore volume, pore distribution, and SEM according to the activation. The results of analyzing the selecting biochar by activating the biochar produced at HTC 300℃, 4 hr by KOH, NaOH, and ZnCl₂ chemicals, the specific surface area was 774~1.387 m²/g, showing a high specific surface area similar to activated carbon, and it was confirmed that micropores with an average pore diameter in the range of 21~24 Å were formed. As a result of SEM observation, the surface was uniform with a certain shape depending on activation. It was confirmed that one pore was developed and the number of pores increased.