• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.8
• /
• pp.178-184
• /
• 2014

In this study, we develop liquid density sensor by measuring of balanced position between gravity and bouyancy, corresponding to liquid density, using distance measuring by magnetostriction technology. For improvement of accuracy of liquid density sensor system. And we derive the related equation between liquid density and moving distance of density sensor, and make the calibration method for liquid density sensor by magnetostriction technology. Using fabricated liquid density sensing system and derived equation, have measured the density of several liquids. And compare it to measuring results using Oscillating U-tube type high accuracy density meter, having 0.000001 g/cc resolution. The deviation of results between two density measuring systems was less than 0.001 g/cc.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.05a
• /
• pp.292-297
• /
• 2005

This paper proposes a simple MPPT control scheme of a Current-Control-Loop Error system Based that can be obtains a lot of advantage to compare with another digital control method, P&O and IncCond algorithm, that is applied mostly a PV system. An existent method is needed an expensive processor such as DSP that calculated to change the measure power of a using current and voltage sensor at the once. Therefore, it is applied a small home power generation system that required many expenses. But, a proposed method is easy to solve the cost reduction and power unbalance problems that it is used by control scheme to limit error of a current control of common sensor. This proposed algorithm had verified through a simulation and an experiment on battery charger using PIC that is the microprocessor of a low price.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.1
• /
• pp.111-120
• /
• 2003

A new stress path test method, which is more suitable f3r evaluating settlements of clay deposits, was introduced. This new method is basically based on back pressure equalization concept and makes it possible to estimate deformations corresponding to all points on a specific stress path by only one test. As a result, deformation characteristics of a clay deposit can be predicted by a few tests and the more practical application of stress path method can be realized. In addition, anisotropic deformation behaviors following arbitrary stress paths also can be experimentally measured by this test method. Experimental applicability of the proposed method was confirmed by performing various stress path tests on remolded kaolinite samples and the actual process to evaluate overall deformation characteristics and settlements was also presented.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.163-173
• /
• 2003

In this paper, a numerical comparison of predictions by limit equilibrium analysis and 3D analysis is presented for slope/pile system. Special attention is given to the coupled analysis based on the explicit finite difference code, FLAC 3D. To this end, an internal routine (FISH) was developed to calculate a factor of safety for a file reinforced slope according to shear strength reduction technique. The case of coupled analyses was performed for stabilizing piles in slope in which the pile response and slope stability are considered simultaneously. In this study, by using these methods, the failure surfaces and factors of safety were compared and analyzed in several cases, such as toe, middle and top of the slope, respectively. Furthermore, the coupled method based on shear strength reduction technique was verified by the comparison with other analysis results.

• Journal of IKEEE
• /
• v.4 no.2 s.7
• /
• pp.241-248
• /
• 2000

A linear power amplifier is particular emphasized on the CDMA system using a linear modulation scheme, because intermodulation distortion which cause adjacent channel interference and co channel interference is mostly generated in a nonlinear power amplifier. In this paper, a new type of linearization technique proposed. It is presented that balanced MESFET predistortion linearizer added. Experimental result are present for Korea PCS(Personal Communication Service) frequency band. The implemented linearizer is applied to a 30dBm class A power amplifier for simulation Performance. The predistortion linearizer improves the 1dB compression point of the HPA about 2dBm, and intermoudulation distortion about 12.5dBc.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.7 no.3
• /
• pp.233-240
• /
• 1995

A large part of shoaling of navigation channel surrounded by fine sand is caused by suspended sediment in non-equilibrium state. We develop a numerical model for predicting shoaling of navigation channel where concentration of suspended sediment in such state is accurately simulated. In this study, effects of channel geometry on the shoaling of the channel are investigated numerically. A composite slope of navigation channel is also proposed to reduce non-equilibrium property of suspended sediment. It is found that the composite slope can effectively reduce non-equilibrium property of suspended sediment and the amount of sediment deposited in the main channel.

• Computational Structural Engineering
• /
• v.9 no.3
• /
• pp.209-216
• /
• 1996

The primary objective of this paper is to grasp many characteristics of buckling behavior of latticed spherical domes under various conditions. The Arc-Length Method proposed by E.Riks is used for the computation and evaluation of geometrically nonlinear fundamental equilibrium paths and bifurcation points. And the direction of the path after the bifurcation point is decided by means of Hosono's concept. Three different nonlinear stiffness matrices of the Slope-Deflection Method are derived for the system with rigid nodes and results of the numerical analysis are examined in regard to geometrical parameters such as slenderness ratio, half-open angle, boundary conditions, and various loading types. But in case of analytical model 2 (rigid node), the post-buckling path could not be surveyed because of Newton-Raphson iteration process being diversed on the critical point since many eigenvalues become zero simultaneously.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.13 no.2
• /
• pp.209-220
• /
• 2000

For non-linear analysis of stiffened shell structures, the total Lagrangian formulation is presented based upon the degenerated shell element. Geometrically correct formulation is developed by updating the direction of normal vectors and taking into account second order rotational terms in the incremental displacement field. Assumed strain concept is adopted in order to overcome shear locking phenomena and to eliminate spurious zero energy mode. The post-buckling behaviors of stiffened shell structures are traced by modeling the stiffener as a shell element and considering general transformation between the main structure and the stiffener at the connection node. Numerical examples to demonstrate the accuracy and the effectiveness of the proposed shell element are presented and compared with references' results.

• Computational Structural Engineering
• /
• v.11 no.4
• /
• pp.155-168
• /
• 1998

보강된 판 및 쉘구조의 안정성 및 후좌굴을 포함하는 기하학적 비선형 해석을 수행하기 위하여, total Lagrangian formulation에 근거한 연속체의 증분평형방정식으로부터 변형된 쉘요소인 유한요소이론을 제시하였다. 쉘구조의 곡률이 불연속적으로 변하거나 쉘부재들이 유한한 각도로 만나는 보강된 판 및 쉘구조의 비선형 해석이 가능하도록 주부재와 보강재 간의 연결점에 대한 일반적인 변환관계를 제시하였으며 좌굴해석 및 기하학적 비선형해석의 경우에 해의 정확성 및 수렴성을 개선시키기 위하여 접선강도행렬 산정시 회전각의 2차항을 포함시켰다. 또한, shear locking 현상을 극복하기 위하여 감차적분을 적용하였고 쉘구조의 좌굴해석에서는 power method를 적용하여 해석의 효율을 높였으며, 후좌굴해석에서는 변위 및 하중증분법을 적절히 결합시켜 보강된 쉘구조의 후좌굴 거동추적이 용이하였다. 또한, 입력자료를 손쉽게 준비하고 좌굴모드 및 후좌굴거동을 효율적으로 분석하기 위하여 전, 후 처리 프로그램을 개발하였고 다양한 해석예제를 통하여 다른 문헌의 해석결과를 비교함으로써 본 연구에서 개발된 유한요소 해석프로그램의 타당성 및 정확성을 입증하였다.

• Korean Journal of Crystallography
• /
• v.14 no.1
• /
• pp.35-38
• /
• 2003

A simple multistep-concentration setting in capillaries was used to control the water-evaporation rate in vapor-diffusion protein crystallization. In the method used, a variety of evaporation rate curves were obtained by using the secondary precipitant solution referred to as “regulatory solution”, which is not directly exposed to the protein solution. The curves were applied to the crystallization of lysozyme as a model protein. The results clearly showed that crystal growth is dependent on the evaporation rate. Especially, the decoupling curves in which precipitant concentration in protein solutions increases to a certain point and then decreases to the equilibrium concentration gave the best crystals.