• International Journal of Highway Engineering
• /
• v.5 no.1 s.15
• /
• pp.11-18
• /
• 2003

Road roughness, as the key factor influencing not only drivers' ride quality and safety but also pavement deterioration, is one of the most important pavement performance indicator to be evaluated by users' subjective assessment. For this reason, a specific number of the pavement roughness has been adopted to monitor the condition of a road for pavement management systems and to evaluate the quality of newly constructed sections, however, none of the unified methodology was internationally accepted. In Korea highway network, road roughness has been used mainly to evaluate newly placed pavement by using 7.6m CP (California Profile meter) to calculate PrI (Profile Index). But this instrument is manually operated to measure road profiles by traffic closure and their interpretation depends on personal bias. Therefore, problems arisen from the manually operated instrument will be overcome by using the APL (Longitudinal Profile Analyzer) which can be operated in the speed of 80km per hour. A study was conducted to correlate the relation from both concrete and asphalt pavement between IRI (measured by APL) and PrI (measured by 7.6m CP). Test results showed that there was a good correlation between IRI and PrI.

• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.167-175
• /
• 2011

Evaluation of fuel consumption for the various road condition and vehicle type is necessary to perform the economic analysis of road construction which is important for the efficient design and management of road. Economic analysis of road should consider the social cost which can be divided into agency cost including initial construction expense, maintenance cost, and so on, and user cost consisting of vehicle operating cost, congestion cost, etc. Since vehicle operating cost depends on the traffic volume, fuel consumption that is a major part of vehicle operating cost will change by traffic volume as well. Fuel consumption is significantly affected by vehicle speed and road condition, especially the roughness. Thus, fuel consumption should be evaluated in terms of road condition, which is not currently considered. In this study, the estimation model of fuel consumption for the passenger cars in Korea has been developed by considering the road condition. First, the relationship between vehicle speed and fuel consumption that is used to calculate the vehicle operating cost for investment evaluation of transportation facility and the initial feasibility study of road construction was investigated. Second, with the consideration of road roughness, fuel consumption of the passenger car was measured. From the measurement, it was found that fuel consumption increased by $80m{\ell}$ per 100km driving as the roughness increased by 1m/km. Therefore, it is recommended that for the economic analysis of road design and management, the fuel consumption should be a function of road roughness.

• 한국방재학회:학술대회논문집
• /
• 2010.02a
• /
• pp.89.2-89.2
• /
• 2010

고속도로에서 주행속도가 높아지게 되면, 도로의 노면 상태에 따라 차량의 안전과 쾌적한 운전자의 환경이 변화될 수 있다. 이처럼 도로의 노면 상태를 결정하는 주된 인자는 도로의 평탄성과 소성변형에 의한 노면의 요철이라고 할 수 있다. 평탄하지 못한 도로를 자동차가 고속으로 주행하게 되면, 자동차의 속도에 의한 도로와의 마찰이 발생하여 자동차에는 매우 큰 흔들림이 발생하게 된다. 또한, 도로의 경우에도 자동차의 차축과 도로면에서 발생하는 충격에 의해 미세한 진동이 발생하게 된다. 그리고 광섬유 브래그 격자(FBG)센서는 외부에서 작용하는 매우 미세한 물리량에 의한 변화의 측정이 가능한 매우 우수한 계측 센서로 사용이 가능하기 때문에 온도보상형 광섬유진동센서를 제작하였고, 이를 고속도로 포장면의 평탄성 모니터링에 활용하고자 하였다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.39 no.1
• /
• pp.55-63
• /
• 2021

The roughness of the road is an important factor directly connected to the ride comfort, and is an evaluation item for functional evaluation and pavement quality management of the road. In this study, data on the road surface were acquired using the latest 3D geospatial information construction technology of ground LiDAR, drone photogrammetry, and drone LiDAR, and the accuracy and roughness of each method were analyzed. As a result of the accuracy evaluation, the average accuracy of terrestrial LiDAR were 0.039m, 0.042m, 0.039m RMSE in X, Y, Z direction, and drone photogrammetry and drone LiDAR represent 0.072~0.076m, 0.060~0.068m RMSE, respectively. In addition, for the roughness analysis, the longitudinal and lateral slopes of the target section were extracted from the 3D geospatial information constructed by each method, and the design values were compared. As a result of roughness analysis, the ground LiDAR showed the same slope as the design value, and the drone photogrammetry and drone LiDAR showed a slight difference from the design value. Research is needed to improve the accuracy of drone photogrammetry and drone LiDAR in measurement fields such as road roughness analysis. If the usability through improved accuracy can be presented in the future, the time required for acquisition can be greatly reduced by utilizing drone photogrammetry and drone LiDAR, so it will be possible to improve related work efficiency.

• Journal of the Society of Disaster Information
• /
• v.9 no.1
• /
• pp.22-29
• /
• 2013

Warm mix asphalt(WMA), which is produced at lower temperatures than hot mix asphalt, has advantages in reductions of fuel consumption and greenhouse-gas emission. In this study, field tests such as skid resistance, rutting(permanent deformation), and roughness were conducted for analysis of long-term field performance of modified warm mix asphalt pavement. Skid resistance after 20 months represents the result similar to initial performance results but rutting and roughness decreased somewhat depending on the period of performance. Measurement results of permanent deformation and roughness could be acceptable because measured pavement location is bus lane that a lot of buses pass and stop. There were no cracks after 11 months, but some minor cracks were observed after 20 months. These results were influenced by increased crack resistance due to fiber addition.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.762-768
• /
• 2003

This paper reports the effects of gain flatness for linearity improvement of feedforward power amplifier fur IMT-2000 band. To investigate the operational characteristics for gain flatness of each amplifier, WCDMA 4FA input signal was used and measured 10 W output power. Especially, linearity improvement for variation of gain flatness of each amplifier was investigated that have an effect on linearity improvement such as delay line, phase, and amplitude imbalances. Variation of gain flatness of main amplifier is 40 MHz and of error amplifier is 40 MHz and 80 MHz bandwidth, respectively. Measured results, gain flatness of main amplifier is less than 1.5 dB and of error amplifier is less than 0.5 dB for more than 20 dB improvement at 5 MHz offset. In addition to that results, the characteristics of feedforward amplifier are drastically varied by gain flatness of error amplifier and it is shown that gain flatness of error amplifier is more important factor for linearity improvement.

• 한국도로학회지:도로
• /
• v.13 no.4
• /
• pp.20-23
• /
• 2011

• International Journal of Highway Engineering
• /
• v.8 no.4 s.30
• /
• pp.25-36
• /
• 2006

Through field surveys and evaluation on several widened concrete pavements, issues on construction and design related problems are broken down into three categories to be discussed; poor smoothness, influence of traffic vibration on concrete curing, and poor connection to the existing pavement. There are many places where about 100mm only of the marginal strip is removed and where defects such as widening and faulting are observed. Also cracks arise again from the patched areas due to stress concentration near the joint. Roughness on the widened concrete pavement was evaluated and there are some stations where the smoothness limit is over passed. For design consideration, shortage of the required force in the tie-bar is expected in case of road widening specially from 3 lanes to 4 lanes. Finally the average pull-out force of specimens made from the current practice was about 57% of the required force. New connecting methods were suggested in this study.

• International Journal of Highway Engineering
• /
• v.14 no.2
• /
• pp.29-36
• /
• 2012

In this study, frequently passing vehicles with two, three, four, and five axles were chosen through traffic volume analysis in Kyung-In Expressway in order to analyze how the road roughness and vehicle speed affect on the dynamic loads for roads in various vehicle classes. Dynamic loads according to chosen vehicles are estimated by TruckSim program. Dynamic load amplification factor is ratio between dynamic and static loads, and it is also determined for each vehicle classes. From the result of dynamic loads estimated by the dynamic load amplification factor, it is shown that for three-axles vehicle, when IRI is 3.5 and vehicle speed is 100km/hr, asphalt pavements receive additional 36% of static loads in maximum. The analysis of the amplification factor according to each vehicle classes also indicates that the amplification factor increases as the distance between the axles becomes smaller and each axle receives more loads.

• Korean Journal of Construction Engineering and Management
• /
• v.24 no.4
• /
• pp.52-59
• /
• 2023

Flatness inspection of PC elements is normally conducted manually by inspectors at manufacturing sites. However, the manual inspection is error-prone and subjective, so it is necessary to develop a robust and efficient flatness measurement method. Recently, a few studies of laser scanner-based flatness inspection have been conducted. However, little attention on field applicability in terms of accuracy, time and cost has been paid. To tackle the limitation, this study aims to compare three sensing method including floor profiler, terrestrial laser scanner and total station for flatness inspection of PC elements. A series of experiments on two full-scale PC slabs were conducted and the results show that the laser scanning method is the most suitable for the PC elements flatness inspection in the aspects of accuracy, time and cost.