• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.17 no.1
• /
• pp.116-123
• /
• 2003

In this paper, interleaved boost converter is applied as a pre-regulator in switched mode power supply. The pre-regulator plays a role to improve power factor. Interleaved Boost Power Factor Corrector(IBPFC) can reduce input current ripple as a single voltage control loop only without inner current loop, because input current is divided each 50% by two switching devices. Each converter cell is also operated in discontinuous current mode and inductor current of each converter is discontinuous. Total input current which is composed by each converter cell is continuous current. Thus, IBPFC is able to improve input current ripple. IBPFC operating in discontinuous current mode can be classified as six modes from switching state and be carried out state space averaging small signal modeling. A control transfer function is obtained according to the modeling. Single voltage control loop is also constructed by the control transfer function. From experimental result, improvement of power factor and input current ripple are verified.

• Korean Chemical Engineering Research
• /
• v.55 no.3
• /
• pp.307-312
• /
• 2017

In this study, the electrochemical performance of surface modified carbon using the PFO (pyrolyzed fuel oil) was investigated by chemical activation with KOH and $K_2CO_3$. PFO was heat treated at $390{\sim}400^{\circ}C$ for 1~3h to prepared the pitch. Three carbon precursors (pitch) prepared by the thermal reaction were 3903 (at $390^{\circ}C$ for 3h), 4001(at $400^{\circ}C$ for 1h) and 4002 (at $400^{\circ}C$ for 2h). Also, the effect of chemical activation catalysts and mixing time on the development of porosity during carbonization was investigated. The prepared carbon was analyzed by BET and FE-SEM. It was shown that chemical activation with KOH could be successfully used to develop carbon with specific surface area ($3.12m^2/g$) and mean pore size (22 nm). The electrochemical characteristics of modified carbon as the anode were investigated by constant current charge/discharge, cyclic voltammetry and electrochemical impedance tests. The coin cell using pitch (4002) modified by KOH has better initial capacity (318 mAh/g) than that of other pitch coin cells. Also, this prepared carbon anode appeared a high initial efficiency of 80% and the retention rate capability of 2C/0.1 C was 92%. It is found that modified carbon anode showed improved cycling and rate capacity performance.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2002.11a
• /
• pp.63-63
• /
• 2002

현재 기계적 합금화법에서는 주로 합금을 구성하는 성분원소 분말을 불활성분위기에서 볼밀처리 함으로써 함금화를 시키거나 모합금에 산화물을 분산시켜 복합화시키는 공정을 통하여 각종 화합물, 비정질상 및 과포화고용체등의 준안정상의 합성 뿐만이 아니라 초미세조직의 생성에 관한 폭 넓은 분야의 연구가 행하여지고 있다. 한편 MA에서는 볼멀처리중 기계적 에너지의 투여에 의하여 실제 반응온도보다 낮은 온도에서 발생하는 특이한 화학반응 즉 Mechanochemical 반응을 일으키 기도 한다. 본 연구에서는 헤마타이트($Fe_20_3$)와 금속윈소인 Ti의 MA처리에 의하여 고상환원반응 을 유기시켜 $Fe-TiO_2$계 nanocomposite 분말재료를 제조하고자 한다. 특히 MA 공정에 있어서 자기 물성의 변화와 X선 회절을 통하여 고상환원반응에 의한 복합분말의 생성과정을 조사하였다. 출발원료는 $Fe_20_3$(고순도화학제,99.9%, 평균입경 0.1$\mu\textrm{m}$)와 금속원소인 Ti(99.9%, 명균업경 150$\mu\textrm{m}$)을 몰비 2:3의 조성이 되도록 하여 MA를 실시하였다. 볼멀은 고에너지 유성형 볼밀장치(독일 제, Fritsch P-5)를 이용하였으며 진공치환형 용기에 원료분말을 장입하여 2회정도 진공배기한 후 아르곤 가스를 충전하여 볼밀을 행하였다. 얻어진 분말시료에 대하여 x-선 회절장치, 전자현미경 (SEM) 및 진동시료형자력계(VSM)를 통하여 결정구조, 미셰조직 빛 자기특성을 조사하였다. $Fe_2O_3-Ti$ 혼합분말의 MA처리 에 의하여 초기단계부터 환원반응과 함께 $Fe_3TIO_{lO}$ 중간상이 관찰 되었으나 30hrs의 MA처리 후 Fe와 산화물 $TiO_2$로 모두 환원되어 $Fe-TiO_2$계 나노복합분말이 얻어짐을 알 수 있었다. 이 때 X션 회절피크의 line broadening으로부터 복합분말의 Fe 명균 결정립 크기는 24nm로 초미세 결정럽의 분말합금이었다. 포화자화값은 볼밀처리에 따라 점점 증가하여 MA 30시간에는 20.3emu/g로 포화됨을 알 수 있었다. 또한 보자력 Hc는 MA초기단계에 350e로 매우 낮으나 30시간 후에는 Hc값이 2600e로 매우 큰 값을 나타내었다. 이것은 환원반응결과 초기에 생성된 Fe의 결정립이 비교적 크고 결정결함이 적으나 볼밀처리를 30시간까지 행하면 Fe 결정렵의 미세화 빛 strain 증가로 magnetic hardening이 일어나기 때문인 것으로 사료된다.

• Journal of Embryo Transfer
• /
• v.29 no.1
• /
• pp.7-12
• /
• 2014

This work was conducted to study the improvement of reproduction rate from the breeding data collected from four farms from January 2007 to October 2010. The average numbers of service per conception were 1) A farm $1.7{\pm}0.1$ times, 2) B farm $1.5{\pm}0.1$ times, 3) C farm $1.5{\pm}0.1$ times, 4) D farm $1.4{\pm}0.1$ times. The average days from calving to conception was $77.4{\pm}4.8$ days in A farm, $150.8{\pm}11.2$ days in B farm, $90.4{\pm}4.5$ days in C farm, and $71.4{\pm}2.5$ days in D farm. Number of artificial insemination (AI) service per conception was higher at the 30 days before first AI ($2.1{\pm}0.2$ times) than at the 31 days after first AI, and the days from calving to conception were shorter at the 90 days before first AI than at the 91 days after first AI. After timed AI (TAI) treatment, the pregnancy rate was 60.3% for the 58 cows with reproductive disorder. In order to improvement of reproduction rates, the farms has to improve the accuracy of estrus detection, pregnancy diagnosis, check-up for reproductive health, and control of day for first AI periods after calving. The result suggests that farmers need the careful management and reproductive examination of farm animals to improve of reproductive efficiency.

• Membrane Journal
• /
• v.14 no.3
• /
• pp.218-229
• /
• 2004

We prepared monodispersed calcium alginate microspheres by controlling various conditions of emulsification procedure using a lab-scale batch type membrane emulsification system equipped with SPG (Shirasu porous glass) tubular membranes. We determined the effects of process parameters of membrane emulsification (ratio of dispersed phase to continuous phase, alginate concentration, emulsifier concentration, type and concentration of stabilizer, transmembrane pressure, concentration of crosslinking agent, stirring speed and membrane pore size) on the mean size and size distribution of alginate microspheres. The increase of the ratio of dispersed phase to continuous phase, transmembrane pressure and alginate concentration led to the increase in the mean size of alginate microspheres. On the contrary, the increase in emulsifier concentration, stirring speed of the continuous phase and concentration of the crosslinking agent caused the reduction of the mean size of microspheres. Through controlling these parameters, monodisperse alginate microspheres with about $6{\mu}{\textrm{m}}$ of the mean size and 1.1 of the size distribution value were finally prepared in case of the using SPC membrane with the pore size of $2.9{\mu}{\textrm{m}}$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.6
• /
• pp.246-252
• /
• 2011

The semiconducting $MnSi_{1.73}$ compound has been recognized as a thermoelectric material with excellent oxidation resistance and stable characteristics at elevated temperature. In the present work, we applied mechanical alloying (MA) technique to produce $MnSi_{1.73}$ compound using a mixture of elemental manganese and silicon powders. The mechanical alloying was carried out using a Fritsch P-5 planetary mill under Ar gas atmosphere. The MA powders were characterized by the X-ray diffraction with Cu-$K{\alpha}$ radiation, thermal analysis and scanning electron microscopy. Due to the observed larger loss of Si relative to Mn during mechanical alloying of $MnSi_{1.73}$, the starting composition of a mixture Mn-Si was modified to $MnSi_{1.83}$ and then $MnSi_{1.88}$. The single $MnSi_{1.73}$ phase has been obtained by mechanical alloying of $MnSi_{1.88}$ mixture powders for 200 hours. It is also found that the grain size of $MnSi_{1.73}$ compound powders analyzed by Hall plot method is reduced to 40 nm after 200 hours of milling.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.12
• /
• pp.6980-6985
• /
• 2014

A micro-conductive pattern was fabricated on an insulating substrate ($SiO_2$) surface using a laser direct writing method. In the LIFT process, when the laser beam irradiates a thin metal film, the photon energy is absorbed by the film and converted to thermal energy, and the thermal decomposition reaction produced by the resulting heat conduction forms a deposit on the substrate. The resistivity of the micro-electrodes deposited through LIFT process with and without polymer coating was measured. The results showed that the electric conductivity of the micro-pattern and micro-structure can be increased approximatly two times when the deposited micropattern is fabricated through a LIFT process with a polymer coating, compared to the case without a polymer coating.

• Applied Chemistry for Engineering
• /
• v.28 no.6
• /
• pp.649-654
• /
• 2017

An activated carbon was prepared from waste citrus peel produced in large amounts in Jeju Island, Korea, using KOH activation and its characteristics was examined. Under the condition of the KOH ratio between 100 and 300%, activation temperature from 400 to $900^{\circ}C$ and activation time from 0.5 to 1.5 h, the iodine adsorptivity of the activated carbon prepared increased but the yield decreased with respect to the increase of each conditions. The iodine adsorptivity and yield of the activated carbon prepared at the activation time of more than 1.5 h were similar to those of using 1.5 h. In addition, as the KOH ratio increased, the specific surface area and pore volume of the activated carbon increased, but the pore diameter decreased. The activated carbon has an average pore diameter of $20{\sim}25{\AA}$. Also, the activated carbon prepared at 300% KOH and $900^{\circ}C$ for 1.5 h has the highest specific surface area of $1,527m^2/g$ and iodine adsorptivity of 1,246 mg/g.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.369-374
• /
• 2005

In this work, the calcium alginate microcapsules containing lemon oil were prepared by emulsification-internal gelation and their potential use as aromatherapy was examined by the controlled release system. The lemon oil encapsulated in the alginate was successfully observed by Fourier transform (FT-IR) spectroscopy and differential scanning calorimeter (DSC) measurements. Analysis of the diameters and shapes of microcapsules was conducted by scanning electron microscopy (SEM). The mean diameters ranging from 4 to 7 um and encapsulation yield ranging from 50 to $85\%$ were obtained. The controlled release of the lemon oil at $37^{circ}$ was demonstrated by the infrared moisture determination (IMDB). It was found that the amount of released lemon oil decreased with increasing concentrations of alginate and $CaCl_2$ due to the higher the cross-linking density of the capsules prepared. The oil release from the capsule was measured as a function of physical force. We confirmed that the external factor could control the collapse of capsule wall and the release rate.

• Membrane Journal
• /
• v.19 no.2
• /
• pp.122-128
• /
• 2009

We prepared monodispersed spherical silica microgels by controlling various conditions of emulsification procedure using a lab-scale membrane emulsification system equipped with SPG (Shirasu porous glass) porous membrane having pore size of $1.5{\mu}m$. We determined the effects of process parameters of membrane emulsification (ratio of dispersed phase to continuous phase, sodium silicate concentration, emulsifier concentration, dispersed phase pressure, stirring speed) on the mean size and size distribution of silica microgels. The increase of the ratio of dispersed phase to continuous phase, dispersed phase pressure and sodium silicate concentration led to the increase in the mean size of microgels. On the contrary, the increase in emulsifier concentration and stirring speed of the continuous phase caused the reduction of the mean size of microgels. Through controlling these parameters, monodisperse spherical silica microgels with about $6{\mu}m$ of the mean size were finally prepared.