• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.91-91
• /
• 2022

하천 합류부에서 수체의 흐름은 매우 역동적으로 변화하며 합류부의 복잡한 3차원 흐름과 난류 구조는 2차류(secondary currents)의 강도변화, 전단층(shear layer)의 뒤틀림 그리고 재순환구역(recirculation zone)의 발생 등 합류부에서의 독특한 특징을 형성한다. 이러한 특징들의 변화는 수체의 흐름구조 뿐만 아니라 하천으로 유입된 오염물의 거동에도 영향을 준다. 기존의 합류부 연구들은 주로 본류와 지류의 합류각이나 유량비에 차이를 두어 합류부의 특징 변화를 모의하였다. 하지만 실제 자연하천에서 홍수방지를 위한 수심확보, 건축자재의 골재수집 등 다양한 목적으로 수행되는 본류의 준설작업으로 인해 발생하는 본류와 지류의 하상면 단차 또한 합류부의 특성에 영향을 미치는 주요한 인자 중 하나이다. 단차가 커짐에 따라 증가하는 지류수체의 낙차는 이차류의 강화를 야기하며 이는 합류부에서의 유속구조를 변화시켜 흐름을 가속시키거나 지체시키며 오염물의 혼합에 영향을 미친다. 본 연구에서는 3차원 수치모의를 통해 90도로 합류되는 수로에서의 흐름구조와 오염물의 혼합에 단차비와 유량비가 미치는 영향을 모의하였다. 유동장 해석을 위해 3차원 RANS (Reynolds-averaged Navier-Stoke) 방정식을 사용하였으며 난류해석은 k-𝜔 SST 모델을 이용하였다. 본류의 경우 11.4m의 수로 연장을 갖고, 하폭은 0.3m이며 수심은 단차의 크기에 따라 변화한다. 지류의 경우는 수로연장 1m, 하폭 및 수로깊이는 0.1m이다. 수치결과의 검증을 위해 이주하(2013)이 수행한 실내 합류수로의 실험결과를 이용하였다. 모의결과를 통해 파악한 합류부의 흐름특성을 이용하여 적절한 2차원 분산계수를 산정한다. 자연하천에서 오염물의 혼합거동을 효과적으로 모의하기 위해 수심 평균된 2차원 이송-분산모형을 이용하는데 이때 적절한 분산계수의 산정이 필수적이다. 본 연구에서는 합류 후 흐름방향에 따라 분산특성이 상이한 구간을 구분하여 분산계수를 산정하였으며 이를 통해 오염물의 거동을 정확하게 모의하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.6
• /
• pp.482-489
• /
• 2020

This study conducted a prototype development and evaluation by performing die-casting mold design, mold manufacturing, and injection condition optimization based on flow and solidification analysis to meet the needs of the coupling parts produced by die casting. Through flow analysis, the injection conditions suitable for 100% filling in the cavity were found to be a molten metal temperature of 670 ℃, injection speed of 1.164 m/s, and filling pressure of 6.324~18.77 MPa. In addition, solidification close to 100 % occurred in all four cavities when the solidification rate was 69.47 %. A defect inspection on the surface and inside the product revealed defects, such as poor molding and pores. In addition, the dimensions of the injected product were within the target tolerance and showed good results. Through the feedback of the results of flow and solidification analysis, it was possible to optimize the mold design, and the injection optimization conditions were confirmed to be a total cycle time of approximately 6.5 seconds. Good quality carrier parts with an average surface hardness of approximately 45 mm from the gate measured at 97.48(Hv) could be produced.

• The Journal of Engineering Geology
• /
• v.18 no.2
• /
• pp.185-190
• /
• 2008

Nine wells have been developed for uses of thermal waters at the Icheon hot spa area. Drilling depths of those hot spring wells range from 166 to 294 m and their piezometric heads are located at about 50 m below the surface. Using the differences between the surface and bottom temperatures within all boreholes, we can simply estimate geothermal gradient in this area. Thus, we obtained the highest, lowest and average gradient values as $64^{\circ}C/km$ from SB-2 well, $45^{\circ}C/km$ from SB-1 well and approximately $54.28^{\circ}C/km$, respectively. However, observing the MRD-2 well additionally drilled into the depth of 996 m, we found out that this study area has widely experienced the temperature disturbance due to thermal groundwater penetration through the fracture systems within the depth of 720 m. Unlikely this phenomenon, we can conclude that the groundwater flow below the depth of 720 m does not exist. Therefore, using only those temperature data below the 720 m depth, we can estimate reasonable geo-thermal gradient values as $33^{\circ}C/km$ in this study area. Pumping test shows that outflowing temperature is $36^{\circ}C$ corresponding to the temperature logging data at 720 m depth.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.27 no.3
• /
• pp.38-46
• /
• 1990

A numerical solution method of the boundary integral equation for axisymmetric potential flows is presented. Those are represented by ring source and ring vorticity distribution. Strengths of ring source and ring vorticity are approximated by linear functions of a parameter $\zeta$ on a segment. The geometry of the body is represented by a cubic B-spline. Limiting integral expressions as the field point tends to the surface having ring source and ring vorticity distribution are derived upto the order of ${\zeta}ln{\zeta}$. In numerical calculations, the principal value integrals over the adjacent segments cancel each other exactly. Thus the singular part proportional to $\(\frac{1}{\zeta}\)$ can be subtracted off in the calculation of the induced velocity by singularities. And the terms proportional to $ln{\zeta}$ and ${\zeta}ln{\zeta}$ can be integrated analytically. Thus those are subtracted off in the numerical calculations and the numerical value obtained from the analytic integrations for $ln{\zeta}$ and ${\zeta}ln{\zeta}$ are added to the induced velocity. The four point Gaussian Quadrature formula was used to evaluate the higher order terms than ${\zeta}ln{\zeta}$ in the integration over the adjacent segments to the field points and the integral over the segments off the field points. The root mean square errors, $E_2$, are examined as a function of the number of nodes to determine convergence rates. The convergence rate of this method approaches 2.

• 한국지구과학회:학술대회논문집
• /
• 2010.04a
• /
• pp.98-98
• /
• 2010

그라우팅은 지반의 공학적인 강도증가를 통한 지지력 향상 및 암반의 투수성 저감을 통해 지하수 유동을 억제하기 위하여 대규모 토목공사 현장의 균열암반 및 댐 또는 제방 등의 지역에서 많이 시행되고 있다. 본 연구는 균열암반지역에서 그라우팅 효과 확인을 위하여 보통 포틀랜드 시멘트(OPC)와 마이크로 시멘트(MC)를 사용하여 그라우팅을 수행하였으며, 그라우팅 전후에 물리검층(시추공영상촬영, 초음파 텔레뷰어검층)을 이용하여 그라우팅 효과 정도를 파악하였다. 연구지역은 경상북도 영주시 평은면 지역으로, 지질은 선캠브리아기 안구상편마암에 시대미상의 흑운모 화강암이 관입을 하였고, 이를 제4기의 충적층이 부정합으로 피복되어 있다. 그라우팅은 일반구간과 단층대구간으로 구분하여 실시하였으며, 두 구간의 이격거리는 서로의 간섭을 피하기 위해 약 40m 간격으로 선정하였다. 주입재(OPC, MC)는 5개의 주입공에서 triangle 방향으로 주입하였으며, 주입정도를 확인하기 위하여 각 구간에 2공씩 확인시추를 하였다. 두 개의 site중 일반구간의 보통 포틀랜드시멘트 주입결과 평균주입량은 48.2kg/공이며 주입 1m당으로 환산하면 Lugeon값 10미만의 지층에서는 1.62kg/m이며, 마이크로시멘트의 평균주입량은 49.6kg/공이며 주입 1m당으로 환산하면 Lugeon값 10미만의 지층에서는 3.86kg/m로 나타났다. 단층대 구간에서는 보통 포틀랜드시멘트의 평균주입량이 40.0kg/공이며, 1m당으로 환산하면 Lugeon값 10미만의 지층에서는 2.75kg/m이며, 마이크로 시멘트는 평균주입량이 56.5kg/공, 주입 1m당으로 환산하면 Lugeon값 10미만의 지층에서는 3.15kg/m로 나타났다. 마이크로시멘트의 주입압은 보통 포틀랜드시멘트에 비해 상대적으로 낮았으며, 그라우팅 개선효과 역시 상대적으로 양호한 것으로 나타났다. 그라우팅 효과확인을 위한 물리검층의 초음파텔레뷰어 해석결과 상대암반강도는 주입전 $250{\sim}750\;kgf/cm^2$, 주입후는 $400{\sim}800\;kgf/cm^2$으로 그라우팅에 의한 암반강도의 상승을 확인할 수 있었고, 시추공영상촬영 분석에서는 시추코어만으로 얻기 힘든 시멘트 충진구간을 직접 확인할 수 있었다. 초음파텔레뷰어의 경우 파쇄대의 분포 및 암반강도 측정을 통한 그라우팅 파악은 가능하였으나 파쇄대 충진물을 확인할 수가 없는 단점이 있었고 이를 시추공영상촬영을 통해 보완할 수 있었다. 다만 물리검층의 경우 그라우팅에 의한 공의 손실로 동일공에 의한 반복 조사가 아닌 경우가 대부분이어서 그라우팅 효과에 대한 정확한 비교가 어려웠으며 추후 이를 보완하기 위한 계속적인 연구가 필요할 것으로 사료된다.

• Fire Science and Engineering
• /
• v.29 no.5
• /
• pp.42-50
• /
• 2015

Three simulation approaches for turbulence were applied for the computation of propane dispersion in a simplified real-scale urban area with one building:, Large Eddy Simulation (LES), Detached Eddy Simulation (DES), and Unsteady Reynolds Averaged Navier-Stokes (RANS). The computations were performed using FLUENT 14, and the grid system was made with ICEM-CFD. The propane distribution depended on the prediction performance of the three simulation approaches for the eddy structure around the building. LES and DES showed relatively similar results for the eddy structure and propane distribution, while the RANS prediction of the propane distribution was unrealistic. RANS was found to be inappropriate for computation of the gas dispersion process due to poor prediction performance for the unsteady turbulence. Considering the computational results and cost, DES is believed to be the optimal choice for computation of the gas dispersion in a real-scale space.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.5
• /
• pp.716-722
• /
• 2017

The present study numerically investigates the effect of obstacles located in the trajectory of fire plume flow on heat flow characteristics by using Fire Dynamics Simulation (FDS) software in an underground combined cycle power plant (CCPP). Fire size is taken as 10 MW and two different locations of fire source are selected depending on the presence of an obstacle. As the results, when the obstacle is in the trajectory of fire plume, hot plume arrives at the ceiling about 5 times slower in the upper of the fire in comparison to the results without obstacle. In addition, the average propagation time of ceiling jet increases by about 70 % with the distance from the ceiling in the upper of the fire, and it increases mainly about 4 times at the distance of 10 m. Consequently, it is noted that the analysis of heat flow characteristics in the underground CCPP considering fire scenarios is essential to develop the fire detection system for initial response on evacuation and disaster management.

• Korean Chemical Engineering Research
• /
• v.50 no.3
• /
• pp.516-521
• /
• 2012

This study developed a simple model to investigate effects of important operating parameters on performance of a bubbling-bed adsorber and regenerator system collecting $CO_2$ from flue gas. The chemical reaction rate was used with mean particles residence time of a reactor to determine the extent of conversion in both adsorber and regenerator reactors. Effects of process parameters - temperature, gas velocity, solid circulation rate, moisture content of feed gas - on $CO_2$ capture efficiency were investigated in a laboratory scale process. The $CO_2$ capture efficiency decreased with increasing temperature or gas velocity of the adsorber. However, it increased with increasing the moisture content of the flue gas or the regenerator temperature. The calculated $CO_2$ capture efficiency agreed to the measured value reasonably well. However the present model did not agree well to the effect of the solid circulation rate on $CO_2$ capture efficiency. Better understanding on contact efficiency between gas and particles was needed to interpret the effect properly.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.6 no.2
• /
• pp.49-62
• /
• 2001

Hydrographic surveys were carried out seven times during May 31, 1998 and September 24, 1998 in order to study the physical environments of the coastal area between Narodo Is. and Sorido Is. in the southern sea of Korea (the South Sea) where the occurrence of Cochlodinium polykrikoides red tide is frequently observed in summer. Temperature and salinity of the water column from the surface to the depth of 30 m exhibit large seasonal variations. Mean temperature of the water column increased by 6 and mean salinity of the water column decreased by 2.71 psu during the observation period. Both the freshwater supplied from the adjacent land and the precipitation over the study area cannot account for the observed salinity variations. The influx of the low salinity water from the offshore area is considered to be the main cause for the observed salinity changes. Surface salinity in the study area shows different spatial distribution in the period of outbreaking, mid-stage and disappearance of the red tide. Especially, salinity was abruptly lowered at the stage of disappearance of red tide as compared to salinity of the previous observation period. Vertical structure of water properties also became vertically homogeneous at the disappearance stage, while it was highly stratified in the previous observation. Such changes can only be explained by the inflow of low salinity water from the offshore, which is considered as the most possible cause for the disappearance of the red tide in the study area. This study suggests that exchanges of water, and chemical and biological factors between coastal areas and of shore area in the South Sea need to be studied in association with the general circulation of the South Sea in order for the better understanding of the occurrence and disappearance of the red tide in the coastal area of the South Sea.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.7
• /
• pp.391-398
• /
• 2020

If the lost energy produced by a propeller can be partially recovered, the propulsive efficiency can be increased, and the fuel consumption reduced. The devices installed for this purpose are called Energy Saving Devices, of which the Contra-Rotating Propeller system is one of the most effective devices. The first problem to be solved to install the Contra-Rotating Propeller system on a large ship is that the mean pressure generated in the journal bearing needs to meet the design criteria of the classifications. In Korea, however, the practical use is being delayed because it cannot overcome this step. The next step is to lower local pressure to increase the reliability. In this study, to solve the mean pressure problem as the first step of practical use, a product carrier with a short stern shape was selected to reduce the weight of the shafting system, and a suitable shafting-system design plan was proposed. Shaft analysis confirmed that the mean pressure of 0.8 MPa (8 bar), which is a design criterion of the classifications for a journal bearing lining material (white metal), was satisfied. In addition, the necessity of reducing the local pressure was also confirmed.