• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05c
• /
• pp.284-289
• /
• 1996

국산 원자로 압력용기강(ASME SA508 cl.3)을 대상으로 표준 샤피충격시험편(2 mm V- notch)과 피로균열(precracked Charpy) 시험편을 제작하여 계장화(instrumented)충격시험을 실시하고, 충격시험시 하중점(load point)의 변위(displacement) 혹은 시간의 변화를 하중의 변화와 함께 측정하였다. 측정결과를 파괴현상 및 파괴역학과 연계시켜 해석하므로서, 가능한한 소량의 시험편(혹은 시험공정)을 사용하여 필요로 하는 인성평가 관련 정보를 획득할 수 있도록 시도하였다. 그 결과, 파괴과정을 나타내는 하중의 변화를 이용하여 Shear fraction 을 예측할 수 있었고, 하중의 변화와 관계된 변위로부터 Lateral expansion을 추정할 수 있었다. 피로균열 시험편 시험결과로 부터는 충격시의 항복하중, 항복변위, 최고하중 등을 획득하여 균열크기의 함수로 표시되는 시험편 Compliance 를 계산하였고, Equivalent energy 법과 J-integral 법을 적용하여 원자로 압력용기강의 탄소성 동적파괴인 성을 평가할 수 있었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.427-431
• /
• 1986

3점 굽힘 시험편, 중앙균열 인장 시험편, 콤팩트 인장 시험편에 대한 J적분식을 하나의 일반화된 형태로 유도한다. 이 일반식은 Eftis와 Liebowitz에 의해 제안된 하중과 하중점 변위 사이의 관계와 Sumpter에 의한 탄성과 소성성분 J적분의 중첩개념을 이용함으로써 유도된다. 일반식에 포함된 .eta.계수를 위 3가지 시험편에 대해서 결정한다. 위 3가지 시험편에 대한 J적분의 최종식은 하중과 하중점 변위곡선 아래의 면적을 측정하지 않아도 되는 형태로 나타난다. 본 연구의 결과식은 Landes등에 의한 실험치와 비교하여 매우 잘 일치함을 보인다.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.2
• /
• pp.119-128
• /
• 2008

In the case of a circular shaft, it is expected that asymmetric loads should apply on the surface rather than symmetric loads due to geographical factors and the non-homogeneity of the jointed rock masses. In this study, discontinuous numerical analysis was carried in order to analyze the characteristics of asymmetric load distribution on the wall of the circular shaft due to anisotropy caused by heterogeneity of rock masses affected by the discontinuities like as a Joint. And it was also analyzed that the effect of the mechanical properties varied with the rock mass rating and horizontal stress with depth had influence in the asymmetric load on the wall of the shaft. In the case of considering the effect of the joint as variable, asymmetric load ratio $(R_p)$, which was defined as the ratio of the load subtracted minimum from maximum to minimum, was below 25% in the hard rock. As regarding the variation of the rock mass rating with depth as variable, the value of $R_p$ was below than 25% in the hard rock, and the value between 30% and 40% in the soft rock. On the other hand, the $R_p$ of fractures rock was between $45{\sim}50%$ which value was much higher than that in better rock mass rating.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.4 s.97
• /
• pp.178-188
• /
• 1999

충격하중을 받는 시험편 높이의 1/4 길이의 notch를 가진 3점 굽힘시험편들의 기계적 거동에 관한 컴퓨터 시뮬레이션을 하고 이 시뮬레이션에 대한 실험적 검증도 하여 그 타당성을 입증하였다. 시험편들의 양쪽 가장자리(지지점)에서 작용되어지는 여러 가지의 하중속도에 대한 경우들과 탄소성 von Mises 재질인 모델들을 시뮬레이션에 포함시켰으며 이들에 대한 결과들을 간극 개구 변위, 반력, 크랙선단 개구 변위 및 변형률등이 속도에 의존되는 재질(점소성 재질)에 대한 시뮬레이션 결과와 비교하였다. 또한 여러가지의 동적 하중을 받는 상황하에서의 안정성이 본 연구의 시뮬레이션을 통하여 비교되었으며 그 차이점들이 규명되었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.4
• /
• pp.277-287
• /
• 1999

Quasi-static tests such as monotonic tension and loading/unloading tension were performed to investigate the bond characteristics and the failure processes for the T-joint specimens made from fiber/epoxy composite material. Two types of specimens, each consists of two components, e. g. skin and frame. were manufactured by co-curing and secondary bonding. During the monotonic tension test, AE instrument was used to predict AE signal at the initial and middle stage of the damage propagation. The damage initiation and progression were monitored optically using m (Charge Coupled Device) camera. And the internal crack front profile was examined using ultrasonic C-scan. The results indicate that the loads representing the abrupt increase of the AE signal are within the error range of 5 percent comparing to the loads shown in the load-time curve. Also it is shown that the initiation of crack occurred in the noodle region for both co-cured and secondarily bonded specimen. The final failure occurred in the noodle region for the co-cured specimen. but at the skin/frame termination point for the secondarily bonded specimen. Based on the results, it was found that two kinds of specimen show different failure modes depending on the manufacturing methods.

• Journal of the Korean GEO-environmental Society
• /
• v.9 no.4
• /
• pp.63-76
• /
• 2008

This research was carried in order to improve design technique for the vertical shaft of which design guide has not been proposed clearly. The deformation tendency of vertical shaft and distribution of the earth pressure around shaft were reviewed with both of theoretical earth pressure distribution suggested in design criteria and measured data which had been gained from 2 constructing shaft. The distribution of earth pressure applied on the vertical shaft was similar with the result of previous theory for the earth pressure proposed by Shin (2007). Moreover it was observed that asymmetric deformation and earth pressure around vertical shaft were caused by inhomogeneity and anisotropy of the ground. The asymmetric earth pressure ratio ($R_p$) in soil and weathered rock were divergent according to the shape ratio. In addition, it is more reasonable that the value of asymmetric earth pressure ratio ($R_p$) is considered less than 0.35 in the case of constructing shaft under rock.

• Proceedings of the KAIS Fall Conference
• /
• 2012.05b
• /
• pp.646-648
• /
• 2012

본 연구에서 다루는 복합재료는 알루미늄 폼으로써 다공성 구조체로 고체 알루미늄 금속에 비하여 비중이 1/10 정도로 작고, 충격에너지 흡수가 우수하다. 본 연구에서는 다공성 심재를 갖는 복합재료 알루미늄 폼 코어의 충격실험을 실시하여 기계적 특성을 파악하였다. 시험편은 알루미늄 폼 코어를 갖는 복합재료로써 시험편에 50J의 저 충격에너지를 가하도록 하였다. 그 결과, 모든 실험에서 스트라이커가 상부면재 통과 시 최대하중이 나타났고, 이때의 최대하중 값은 약 5.5 KN으로 나타났다. 또한 최대 하중 발생 시간은 50J일 때 약 4.2 ms가 나왔다. 최대 하중이 발생한 후, 즉 상부 면재 통과 후에 실험에서는 약 10 mm정도를 더 뚫으면서 심재에 까지 손상을 주었지만 하부 면재에는 손상을 주지 못하였다. 이로써 스트라이커가 알루미늄 폼 코어 샌드위치 복합재료를 통과 할 때 상부면재 통과 시 최대 하중이 발생하고 심재를 지나며 서서히 감소되는 것을 볼 수 있었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.29 no.1
• /
• pp.21-26
• /
• 2009

In order to determine the effective way of measuring the Mode I stress intensity factor($K_1$) by means of the alternating current potential drop(ACPD) technique for a material containing a two-dimensional surface crack, the change in magnetic flux in the air due to load was studied theoretically and experimentally. The magnetic flux in the air between crack surfaces is uniform and is not changed by increasing the load in the specimen and experimental results are the same as those obtained from theoretical analysis. Therefore, the change in potential drop due to load in the measuring system which was designed to induce a large amount of electro-motive force was caused by the change in internal inductance of material and the change in the mutual inductance concerned with internal inductance of material.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.108-108
• /
• 2004

전동차의 차체는 최대승객하중의 운행조건 하에서 시스템의 기능을 만족하도록 강성 및 강도를 갖도록 되어 있으며, 수직하중 및 수평하중을 지지하는 언더프레임(Under Frame), 측벽의 하중을 지지하는 측면구조틀(Side Frame) 지붕을 구성하는 지붕구조틀(Roof Frame), 끝막이 골조(End Frame)로 구성되어 있다.(중략)

• Journal of the Korean Society for Nondestructive Testing
• /
• v.22 no.2
• /
• pp.125-131
• /
• 2002

we analyzed acoustic emission signals obtained from three kinds of brittle materials under compression load by Vickers hardness tester. The results obtained can be summarized as follows; The signal in each material could be divided into three signal based on the properties of load. All specimens were not detected acoustic emission signals in stage II which was load constant region., and were detected in stage I and stage III. Glass was detected high amplitude signals in stage III. $Al_2O_3\;and\;Al_2O_3/Sic$ were detected high amplitude signals in stage I.