• 레미콘
• /
• no.4 s.55
• /
• pp.39-53
• /
• 1998

• Magazine of RCR
• /
• v.13 no.4
• /
• pp.54-60
• /
• 2018

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05c
• /
• pp.69-73
• /
• 2009

Plan of concrete pumpability test or the theoretical character knowledge in the mechanic is become accomplished with character. But the character knowledge of the concrete is not considered appropriately, The theoretical background and assumed fact is a little different representative characteristic of the concrete. Concrete pumping experiment result it leads consequently and is produced the coefficient of friction which in concrete type and sending in more pressure it follows changes must grasp the tendency which. But until currently the majority experiment and research did not pass by this process. Grasps the coefficient of friction change tendency which it follows in concrete type and when pumping concrete more pressure data fundamentally from the experimental research which it sees consequently under providing the man with underdeveloped genital organ.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.239-240
• /
• 2023

In this study, concrete pumpability was investigated using a sliding pipe rheometer when the slump was different, and the cause was analyzed by comparing the actual field pump pressure. As a result of the experiment, it was found that the concrete pumpability was greatly affected by the slump measurement value.

• Journal of Animal Environmental Science
• /
• v.11 no.1
• /
• pp.25-34
• /
• 2005

The study aimed to develop a tractor drawn animal slurry manure sub-soil injector for arable land and thus, can reduce the waste management cost through effective treatment and utilization of animal slurry manure. The application of animal slurry manure to agricultural land will probably be one of the most effective ways to enrich the soil with vital nutrients. However, some existing slurry manure spenders are not suitable in the field because of their adverse effects to the environment. Based on this premise, a prototype was designed and assembled using 5 sub-soiling standards attached to the sin injector device. The traction force of the Prototype measured in the depth of 10 cm and 15 cm from the ground surface of a paddy field was 1,062 kgf and 1,214 kgf, respectively. A unique feature of the machine was that there was an equal volume of slurry manure flowing from each delivery pipe and regulated by a pressurized container that was likewise synchronized with the speed of the tractor The sub-soiling manure injection system can mitigate or reduce the harmful emission of obnoxious gases and malodor during the injection operation.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.187-191
• /
• 2008

It is necessary to develop a technology for effectively controling explosive spalling of high strength concrete caused increasing construction of high rise building and putting up the fireproof standard of high strength concrete by MLTM (Ministry of Land, Transport and Maritime Affairs). Accordingly, it was investigated basic properties such as slump, air content and compressive strength, and fire resistance properties of high strength concrete using polypropylene fiber for field application as a countermeasure for explosive spalling of concrete on fire in this study, As a test result, it was confirmed that PP fiber is available as fire resistance method of high strength concrete.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2007.11a
• /
• pp.1-4
• /
• 2007

Because reinforced concrete structures were being high more and more in recent year, concrete was being demanded high performance of high strength and high fluidity. But various characteristics must be confirmed besides guarantee of demand strength in ultra-high strength concrete. In ultra-high strength concrete, autogenous shrinkage and drying shrinkage grow big because of a low water cement ratio and much quantity of binder. So dangerousness of crack generation grow big in early ages. And ultra-high strength concrete is influenced by use materials more than ordinary strength concrete. In this study we were examined mix design, atuogenous shrinkage and pumpability of ultra-high strength concrete to apply on the ground.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.12
• /
• pp.1119-1125
• /
• 2010

Most of the sludge pre-treatment methods to improve the anaerobic digestibility of sludge are not practied in the fields with low economical efficiency. The venturi cavitation system (VCS) adopting hydrodynamic cavitation is simple and requires low energy. This research was conducted to investigate the optimum design and operating conditions of the VCS. The experimental results indicated that the optimum number of venturi in series was three, and the suction mode operation of the pump yielded 1.6 times higher pre-treatment efficiency per unit energy consumption than the discharge mode. The combination of venturies with different throat sizes did not affect the pre-treatment efficiency. Also, the parallel installation of the three in series venture unit yielded 30% higher pre-treatment efficiency per unit energy consumption than the single unit. Under parallel conditions, the solubilization efficiency was 5.6 mg ${\Delta}SCOD/g$ TS/kWh, which is higher than the previously reported value.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.577-580
• /
• 2008

This paper was discussed about in-site application of heavyweight(or high density) concrete. Heavyweight concrete was placed with the method of conventional. Placement of conventionally mixed heavyweight concrete is subject to the same considerations of quality control as normal density concrete, except that it is far more susceptible to variations in quality due to improper handling. It is particularly subject to segregation during placement. Segregation of heavyweight concrete results not only in variation of strength but, far more importantly, in variation in density that are intolerable for work this type, since this adversely affects shielding properties. Heavyweight concrete materials and heavyweight concrete should be sampled and tested prior to and during construction to insure conformance with applicable standards and specifications.

• Journal of the Society of Disaster Information
• /
• v.20 no.1
• /
• pp.20-31
• /
• 2024

Purpose: Research and development of high-strength concrete enables high-rise buildings and reduces the self-weight of the structure by reducing the cross-section, thereby reducing the thickness of beams and slabs to build more floors. A large effective space can be secured and the amount of reinforcement and concrete used to designate the base surface can be reduced. Method: In terms of field construction and quality, the effect of reducing the occurrence of drying shrinkage can be confirmed by studying the combination of low water bonding ratio and minimizing bleeding on the concrete surface. Result: The ease of site construction was confirmed due to the high self-charging property due to the increased fluidity by using high-performance water reducing agents, and the advantage of shortening the time to remove the formwork by expressing the early strength of concrete was confirmed. These experimental results show that the field application of ultra-high-strength concrete with a design standard strength of 100 MPa or higher can be expanded in high-rise buildings. Through this study, we experimented and evaluated whether ultra-high-strength concrete with a strength of 130 MPa or higher, considering the applicability of high-rise buildings with more than 120 floors in Korea, could be applied in the field. Conclusion: This study found the optimal mixing ratio studied by various methods of indoor basic experiments to confirm the applicability of ultra-high strength, produced 130MPa ultra-high strength concrete at a ready-mixed concrete factory similar to the real size, and tested the applicability of concrete to the fluidity and strength expression and hydration heat.