• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.866-869
• /
• 2015

In this paper, we propose a device for detect front object using low-price the CW Doppler sensor to prevent safety accident such as a bicycle, an electric wheelchair users. For this propose, we develop a signal process board and the object motion detect algorithm using to analyzing output signal of the CW Doppler sensor. Output signal from CW Doppler sensor is analog I and analog Q. The CW Doppler sensor shows phase I and phase Q of object differently when the object approach, stop, drop by sensor. We develop an algorithm that can detect object by discrimination information of phase using the CW Doppler sensor. The verification use firmware of applied hardware and algorithm. Then, the motion information can be confirming output depending on motion object by experiment normally. As a result, we check that the sensing information output by following motion of object and confirm an algorithm and motion of signal processing board.

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.43 no.4 s.310
• /
• pp.15-22
• /
• 2006

Nowadays, there is called energy saving, that it is accomplished with a lot study and application development as according to demand of all around world. It is using to network device of wire or wireless such as internet, lan, plc, and zigbee and that we should be accomplished to study about method that spending a little cost to fatal error in control system that be expected of frequent occurrence on network, and that have method to do construction a little bit tried out. Also, in that such a embedded system with network function case, there is important thing that it is remote management to network node and control methods to trust because firmware upgrade have the advantage of more than the other device. In this paper, we have verified through a result of experiment for efficient remote management and control method as previously stated in this paper, that it is area of the PLC for sensor node and doing management to relay, and implementation of the LACC which is core part of the ESS, and in order to get a result to trust from doing analysis of capacity and test.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.6
• /
• pp.65-73
• /
• 2012

Wrist wearable device for the measurement of pulse rate, ECG, and activity during normal daily life, which could be used for the continuous monitoring and remote transmission of acquired data, was developed. Pressure sensor, device attached electrodes, and 3-degree accelerometer were used. Analysis algorithm and firmware program were established for providing diagnostic information for the users. Results of this study, possible for the management of health report and transmission of the results through bluetooth by wearing simple personal wrist device, could be used for the development of portable device in the u-healthcare environment.

• Journal of the Korea Society of Computer and Information
• /
• v.20 no.4
• /
• pp.33-40
• /
• 2015

This paper presents the design and implementation of the educational remote controlled robot system including remote sensing in the embedded environment. The design of sensing information processing, software design and template design mechanism for the programming practice are introduced. LPC1769 using Cortex-M3 core as CPU, LPCXPRESSO as debugging environment, C language as firmware development language and FreeRTOS as OS are used in development environment. The control command is received via RF communication by the server and the robot system which is operated by driving the various sensors. The educational procedure is from robot demo operation program as hands-on practice and then compiling, loading of the basic robot operation program, already supplied. Thereafter the verification is checked by using the basic robot operation to allow demo operation such as hands-on-training procedure. The original protocol is designed via RF communication between server and robot system, and the satisfied performance result is presented by analyzing the robot sensing data processing.

• Journal of Korea Multimedia Society
• /
• v.5 no.2
• /
• pp.215-221
• /
• 2002

In high speed optical disc devices, the vibration caused by unbalanced displacement leads the focus and tracking servo systems to be unstable, and increases the data search time. In this paper, we propose a new scheme to solve the unbalanced displacement problem. The proposed method detects the unbalanced rate by differential amplifying optical power received at photo diode and converts it into an electrical signal. controlling the speed of spindle motor, according to the detected unbalanced rate, makes it possible to improve the performance of tracking and data searching tasks. Also, we analyze the dynamic characteristics of focus and tracking servo systems in high speed mode and provide the firmware and hardware architecture that the proposed method can be installed as an add-on- module in the existing system.

• Journal of Industrial Convergence
• /
• v.20 no.10
• /
• pp.17-24
• /
• 2022

Lora, a non-band network technology of the long-distance wireless standard LPWAN standard, uses ABP and OTTA methods and AES-128-based encryption algorithm (shared key) for internal terminal authentication and integrity verification. Lora's recent firmware tampering vulnerability and shared-key encryption algorithm structure make it difficult to defend against MITM attacks. In this study, the consensus algorithm(PBFT) is applied to the Lora network to enhance safety. It performs authentication and PBFT block chain creation by searching for node groups using the GPS module. As a result of the performance analysis, we established a new Lora trust network and proved that the latency of the consensus algorithm was improved. This study is a 4th industry convergence study and is intended to help improve the security technology of Lora devices in the future.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.38 no.6
• /
• pp.11-17
• /
• 2001

Design and implementation of the MAC protocol processor prototype for high speed wireless LAN, which has interface with 5GHz OFDM PHY layer, is presented. We analyze the IEEE 802.11 MAC protocol specification and then separate the MAC protocol functions to be implemented by hardware and firmware and define the interface in which frames can be exchanged. That is, it is considered that high speed queue processing and interfaces with RISC processor and OFDM PHY layer. Protocol control and transmission/reception functions of the MAC functions are implemented in hardware in order to guarantee high speed processing in MAC layer. The developed MAC hardware block operates at 10MHz main clock. Therefore, transmission rate in PHY layer is about 80Mbps because data transmission/reception between MAC layer and PHY layer is performed as unit of octet. The designed FPGA MAC function chip has been implemented in wireless LAN test board and it is verified that DCF function is operated correctly.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.5
• /
• pp.1-8
• /
• 2013

This paper implements an integrated vehicle chassis system of ACC(Adaptive Cruise Control) and LKS(Lane Keeping System) based on OSEK OS to vehicle operating system and analyzes its performance through experiments. In recent years active safety and advanced driver assistance system has discussed to improve safety of vehicle. Among the rest, We integrate ACC that controls longitudinal velocity of vehicle and LKS that assists a vehicle in maintaing its driving lane, then implement integrated control system in vehicle. Implemented control system uses OSEK/VDX proposed standard, which is aiming at reusability and safety of software for vehicle and removal hardware dependence of application software. Redesigned control system based on OSEK OS, which is supported by OSEK/VDX, can manage real-time task, process interrupt and manage shared resource. We show by results performed EILS(ECU-In-the-Loop Simulation) that OSEK OS-based integrated controller of ACC and LKS is equivalent conventional integrated controller of ACC and LKS.

• Journal of the Korean Geosynthetics Society
• /
• v.23 no.2
• /
• pp.43-52
• /
• 2024

Recent abnormal climate conditions have increased the risk of slope collapses, which frequently result in significant loss of life and property due to the absence of early prediction and warning dissemination. In this paper, we develop a slope condition analysis system using IoT sensors and AI-based camera to assess the condition of slopes. To develop the system, we conducted hardware and firmware design for measurement sensors considering the ground conditions of slopes, designed AI-based image analysis algorithms, and developed prediction and warning solutions and systems. We aimed to minimize errors in sensor data through the integration of IoT sensor data and AI camera image analysis, ultimately enhancing the reliability of the data. Additionally, we evaluated the accuracy (reliability) by applying it to actual slopes. As a result, sensor measurement errors were maintained within 0.1°, and the data transmission rate exceeded 95%. Moreover, the AI-based image analysis system demonstrated nighttime partial recognition rates of over 99%, indicating excellent performance even in low-light conditions. Through this research, it is anticipated that the analysis of slope conditions and smart maintenance management in various fields of Social Overhead Capital (SOC) facilities can be applied.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.4
• /
• pp.157-166
• /
• 2022

The most commonly used wireless communication technologies in IoT technology include ZigBee, WiFi, Bluetooth, and Z-Wave. In particular, Z-Wave is currently one of the preferred wireless communication technologies, with a global market share of 60 % of these technologies. In this research, a temperature and humidity sensor module using a Z-wave protocol was designed and manufactured by referring to the data sheet. Subsequently, the Z-Wave protocol was analyzed during the operation of the sensor module, and the firmware of the controller module was mounted and implemented. In addition, a program for monitoring the temperature and humidity information from the sensor module was developed and validated. Finally, the performance of the sensor module was validated through master distance and low power tests on it and its reception data success rate.