• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.3
• /
• pp.24-33
• /
• 2012

The present work has suggested the design methods of the bolt body for making the anti-releasing bolts and provided the changed properties of the bolt body after explosion. To prove this work, two models of the anti-releasing bolts, M10 and M20, are produced and the expansion properties of each model are experimentally obtained. This study verify that the expansion of the bolt body is reproducible and the expansion rate could be controlled by the combination of the design factors and the anti-releasing characteristics could be quantified. It also could provide the data that would be needed to make the bolts with the anti-releasing effect.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.381-385
• /
• 2005

Recently, spacecraft technology trends can be expressed three words, i.e. 'faster, cheaper and smaller'. Among these systems, micro propulsion device is an essential component. Also micro nozzle is the most important part in the micro propulsion device. In case of cold-gas thruster, micro nozzle converts the stored energy in a pressurized gas into kinetic energy through expansion ratio. In this paper we report characteristics of micro nozzle with throat expansion ratio and ratio of specific heats. We measure thrusts using strain gauge based thrust measurement system. We can estimate the micro nozzle performance through experiments.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1141-1148
• /
• 2008

One of the methods to increase the efficiency of an engine is to expand pressures obtained from combustions equal to the pressure of atmosphere as much as possible and then convert thermal energy into mechanical energy also as much as possible. In this research, the Diesel cycle was thermodynamically interpreted to evaluate the possibility of high efficiency by converting Diesel engines to the Atkinson cycle, and general cycle features were analyzed after comparing these two cycles. In the case of fuel air the Diesel-Atkinson cycle considering intake and exhaust similar to real cycles, the value of thermal efficiency and average effective pressure increased, though their values were smaller than those of standard air amount cycle, when expansion compression ratio increased. When normal Diesel engines of which compression stroke and expansion stroke are all the same, was converted to the Atkinson cycle by changing the time of intake value close, combustion pressure reduced due to reduced expansion compression ratio and intake air amount due to decreased effective cycle volume.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.42-49
• /
• 2006

In this research. the diesel cycle was thermodynamically interpreted to evaluate the possibility of high efficiency by converting diesel engines to the high expansion diesel cycle, and general cycle features were analyzed after comparing these two cycles. Based on these analyses. an experimental single cylinder a long stroke with high expansion-diesel engine. of which S/B ratio was more than 3, was manufactured. After evaluating the base engine through basic experiments, a diesel engine was converted into the high expansion diesel engine by establish VCR device and VVT system Accordingly, the high expansion diesel cycle can be implemented when the quantity of intake air is compensated by supercharge and the effective compression ratio is maintained at its initial level through the reduction of the clearance volume. In this case, heat efficiency increased by $5.0\%$ at the same expansion-compression ratio when the apparent compression ratio was 20 and the fuel cut off ratio was 2. As explained above, when the atkinson cycle was used for diesel cycle, heat efficiency was improved. In order to realize high expansion through retarding the intake value closing time, the engine needs to be equipped with variable valve timing equipment, variable compression ratio equipment and supercharged pressure equipment. Then a high expansion diesel cycle engine is realized.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.382-385
• /
• 2008

박막형 태양전지 분야는 저가이고 가볍다는 특징을 가지고 있으며, 휘어지는 기판재를 적용하여 플렉서블 태양전지를 제조할 수도 있다는 장점을 가지고 있다. 본 연구에서 플렉서블 태양전지에 적합한 금속기판재를 제조하는 연구를 수행하였다. 일반적으로 기판재와 cell을 구성하는 반도체 층의 열팽창 거동 차이에 의한 열변형이 태양전지의 공정안정성에 영향을 주는 것으로 알려져 있었으며, cell을 구성하는 반도체 층과 열팽창 거동이 유사한 금속기판재의 적용이 필요하다. 이러한 특성을 쉽게 제어할 수 있는 금속기판재를 얇게 제조하기에 적절한 방법은 전주법이다. 전주법을 적용하여 조성 및 두께가 다른Ni 계 합금의 열팽창 거동을 TMA 장비를 사용하여 측정하였으며, 태양전지 제조에 사용되는 고온공정시 안정성 확보를 위하여 열처리후에 금속기판재의 열팽창 거동을 측정하였다. 그리고 전산해석tool 을 활용하여 가상의 CIS 플렉서블 태양전지 제조공정을 설정하고 고온공정온도에서 상온으로 냉각시 발생되는 층간 열변형 연구를 수행하였다. 그리고 플렉서블 태양전지용 기판재로 Ni 계 합금표면에 절연체인 $SiO_2$ 증착 연구를 수행하여 Fe-52Ni 합금에서 안정적인 절연층을 얻을 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.40-45
• /
• 2011

The purpose of research is to understand the characteristics of refrigeration system having a liquid-vapor phase separator after expansion device and precooling heat exchanger. After expansion process of typical refrigerant of freezer, R134a, the cold vapor of the expanded refrigerant mixture is separated in the liquid-vapor separator and introduced in the precooling heat exchanger to enable the liquid refrigerant to be subcooled. The analysis results showed that the increasing rate of refrigeration capacity and COP can be 8.6% and 1.4%, each. The cause of these performance improvements is due to the difference of the slope of saturated vapor and saturated liquid lines in Mollier diagram of refrigerant.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.2
• /
• pp.155-161
• /
• 2008

The grounding systems provide a low resistance path for fault or normal currents into the earth. The material for reducing ground resistance is buried around the grounding electrode to increase its effective size of the electrode and thus to obtain low ground resistance. Increasing the contacting area with the grounding electrode is effective for lowering the ground resistance in soils. Using this idea the conductive expansion ground resistance reducing material was developed. In this paper experimental data has shown that the ground resistance reduction method using proposed material is superior to using a typically available commercial ground resistance reducing material.

• Journal of the Korean Chemical Society
• /
• v.41 no.3
• /
• pp.123-129
• /
• 1997

In order to consider the reduced mass effects on the out-of-plane ring inversion vibration of 1,3-CHD, the vector-based computer program has been written and the kinetic energy expansion function for the large amplitude ring inversion vibration has been calculated using this program. The structural parameters for the calculations have been determined from the ab initio HF/6-31G** calculation. The potential energy function for the out-of-plane ring inversion vibration of 1,3-CHD has been determined from the kinetic energy expansion function and previously reported low-frequency Raman data. The vibrational Hamiltonian calculation including kinetic energy expansion function made it possible to determine the more reliable out-of-plane potential energy function for the ring inversion of 1,3-CHD.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.201-204
• /
• 2008

The proposed method, capable of predicting various stress-strain responses in axially loaded concrete confined with FRP (Fiber Reinforced Polymers) composites in a rational manner, is based on the fact that the volumetric expansion due to progressive microcracking in mechanically loaded concrete is an important measure of the extent of damage in the material microstructure. The elastic modulus expressed as a function of area strain and concrete porosity, the energy-balance equation relating the dilating concrete to the confining device interactively, the varying confining pressure, and an incremental calculation algorithm are included in the solution procedure. This procedure enables the evaluation of lateral strains consecutively according to the related mechanical model and the energy-balance equation, rather than using an empirically derived equation for Poisson's ratio or dilation rate as in other analytical methods.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.311-317
• /
• 2003

The swelling index of clayey soil was examined by constant rate of strain(CRS) consolidation test. Four kinds of strain rate were applied during unloading. The strain rates are l/l, l/5, 1/10, l/l 5 of loading. The strain rates during loading are 0.05%/min and 0.03%/min. From the test results using standard consolidometer, the swelling indexes were much similar values in case of 1/5 or 1/10 of the strain rate during loading stage. In the relation between effective stress and excess pore water pressure ratio, it was found that the existence of cross point and the stress level can be separated into two zones according to the swelling index.