• Journal of Korean Society of Steel Construction
• /
• v.26 no.4
• /
• pp.277-288
• /
• 2014

In this study, the local displacement and moment characteristics of a plate stiffened with closed ribs are analyzed according to the dimensions of stiffened plates. The analyzed results of various stiffened plates under square distributed load show that the effect of the loading panel width to the local behavior is dominant but that of the next panel width is very small. And the local behavior of reference stiffened plates can be expressed by the angle between the plate and the rib, and that of other stiffened plates can be obtained by multiplying ratio functions of the loading panel width, plate thickness, rib thickness, rib height and next panel width and they give good results. Applying ratio functions to other loading sizes shows that the applicability of ratio functions except for the loading panel width is proved and the modified ratio functions of the loading panel width improve error ratios. Therefore, the local displacement and moments of a plate stiffened with closed ribs can easily achieve proper results regardless of the dimensions using ratio functions proposed in this study.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.3
• /
• pp.66-80
• /
• 1996

Recently, HT steel has been widely used in structure, and this enables to reduce the plate thickness. To use the HT steel effectively for a ship hull, the plate thickness becomes thin so that plate buckling may take place. Therefore, precise assessment of the behaviour of plat above primary buckling load is important. The plate under the load, that is called, secondary buckling load may undergo abrupt changes in wave form after primary buckling. This is very important when the collapse strength of the whole structures is considered. From this point of view, this paper discusses secondary buckling behaviour of thin plate under inplane compressive loading. A elastic large deflection analysis of plates with initial imperfection is performed assuming uniaxial compression, respectively, and the influence of secondary buckling is investigated. It is known that square plate is not influenced by non-symmetrical deflection coefficient but influenced by symmetrical deflection coefficient. Also, it has been found that rectangular plate($\alpha$=a/b) is influenced by all deflection coefficient, and the reduction of inplane stiffness of the plate after primary buckling is continued.

• Journal of the Korean Institute of Gas
• /
• v.8 no.2 s.23
• /
• pp.35-41
• /
• 2004

This paper presents the stress and deformation characteristics of $9\%$ nickel based inner tank bottom plate in full containment LNG storage tank. When a . maximum hydrostatic pressure applies the bottom plate of inner tank, the maximum = f stress and displacement distributions of the bottom plate have been analyzed as ' functions of inclined angle of the bottom plate, and the thickness and length of the annular plate between the shell plate and bottom one. The calculated results indicate that the taper of the bottom plate is recommended by 100${\~}$200 : 1 for $140,000m^3$ storage capacity of the inner tank. The results recommend that the thickness of the annular plate is around 20mm and the length is greater than 3m for a maximum hydrostatic pressure of $140,000m^3$ tank capacity.

• Composites Research
• /
• v.20 no.5
• /
• pp.1-6
• /
• 2007

This study was performed to make a comparison on low-velocity impact behavior between graphite/epoxy composite laminate and steel plate. In order to validate the proposed scheme fur the impact behavior of the plate, the Karas's impact model was used. The impact models for this comparative study are the graphite/epoxy composite plate having $[0/90/45/-45/-45/45/90/0]_{8S}$ laminate sequence and the steel plate with a steel ball impactor. The low-velocity impact behaviors for two types of plates were comparatively investigated and performed by considering different impactor velocities and weights respectively. In this investigation, it was found that the composite laminate has impact energy absorption effect due to more flexible behavior than the steel plate, and also it has better characteristics on impact damage and weight.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.12
• /
• pp.1233-1242
• /
• 2009

In this paper, a Base Station Antenna(BSA) utilizing Artificial Magnetic Conductor(AMC) as reflector instead of common conductive plate to improve radiation characteristics and achieve low-profile is proposed. In the case of the conventional BSA on conductive surface which acts as a reflector, a secondary radiation is caused at the corner of the conductive surface, and it increases the back-lobe of the antenna, resulting in deteriorating the radiation characteristic of the conventional BSA. However, using the AMC, the back-lobe of the BSA can be largely reduced by the surface wave suppression. And the Side-Lobe Level(SLL) is also improved, resulting in preventing the service area overlapped. Furthermore, due to the $0^{\circ}$ reflection phase on AMC, the profile of the BSA can be also reduced.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.3
• /
• pp.219-228
• /
• 2010

This paper describes an experimental research on the structural behavior and the ultimate strength of longitudinally stiffened plates subjected to local, distortional, or mixed-mode buckling under compression. The stiffened plate undergoes local, distortional, or interactive local-distortional buckling according to the flexural rigidity of the plate's longitudinal stiffeners and the width-thickness ratios of the sub-panels of the stiffened plate. A significant post-buckling strength in the local and distortional modes affects the ultimate strength of the longitudinally stiffened plate. Compression tests were conducted on stiffened plates that were fabricated from 4mm-thick SM400 steel plates with a nominal yield stress of 235MPa. A simple strength formula for the Direct Strength Method based on the test results was proposed. This paper proves that the Direct Strength Method can properly predict the ultimate strength of stiffened plates when the local buckling and distortional buckling occur simultaneously or nearly simultaneously.

• Journal of the Microelectronics and Packaging Society
• /
• v.2 no.1
• /
• pp.69-75
• /
• 1995

압전세라믹스를 제조하여 발음체 소자의 두께 직경등의 칫수 변화에 따른 압전발을 체 소자의 전기적 특성 및 압전세라믹스와 금속진동판의 상관관계를 조사하고 공명용 수지 case등을 고려하여 공진 주파수에서 효율좋은 음을 발생시킬수 있는 압전발음체를 설계하였 다. 본 실험에서 사용딘 압전세라믹스 (Pb0.95Sr0.05)(Zr0.53Ti0.47)O3+0.8wt%Nb2O5의 특성은 전 기기계 결합계수(KP)가 69%이며 기계적 품질계수(Qm)은 87 비유전율은 2100 tan$\delta$는 0.016이었다. 금속진동판의 공진주파수는 사용되는 재료의 stiffness와 관계가 있고 주파수 -impedance 특성은 재질의 음속, 밀도, Young율 등에 크게 의존하였다. 주파수 대역 2.0~ 2.2khz에서 공진시키기 위한 공명체의 설계에서 압전세라믹스의 외경과 두께가 각각 14mm, 0.1mm 이고 금속진동판의 그것이 각각 20mm, 0.1mmdlfEo 공명기는 방음공의 직경이 3.0mm, cavity의 직경이 18.5mm, cavity의 높이가 4.5mm의 구조로 설계되었을때가 최적조 건이었다.

• Journal of the Society of Naval Architects of Korea
• /
• v.33 no.1
• /
• pp.109-123
• /
• 1996

A series of quasi-static crushing tests were carried out on thin-walled square tube specimens with axial and/or circumferential stiffeners including unstiffened specimens. The effective crushing length and mean crushing strength of the test specimens were investigated. Using the equivalent plate thickness approach, a simplified analytical model for predicting the mean crushing strength of stiffened square tubes has been developed.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.1
• /
• pp.37-44
• /
• 1999

비등방성으로 적층된 복합판 및 쉘구조물에서 온도와 습도의 급격한 변화는 구조물의 강도와 성능을 저하시키는 중요한 원인이 된다. 더욱이 하중에 의한 역학적 변위와 조합될 때에는 좌굴, 대변형 혹은 고응력 상태를 유발하게 된다. 본 연구에서는 이중 퓨리에급수를 이용하여 3차의 전단변형함수로 가정된 평형방정석을 전개하고 폭-두께비, 형상비의 변화 그리고 재료의 성질에 따른 결과에 대하여 고찰하였다.

• Radiation Oncology Journal
• /
• v.14 no.4
• /
• pp.339-345
• /
• 1996

Purpose : This study was performed for adequate irradiating tumor area when 6 MV linear accerelator photon was used to treat the head and neck tumor. The skin surface dose and maximum build-up region was measured by using a spoiler which was located between skin surface and collimator. Methods : A spoiler was made of tissue equivalent material and the skin surface dose and maximum build-up region was measured varing with field size, thickness of spoiler and interval between skin and collimator. The results of skin surface dose and maximum build-up dose was represented as a build-up ratio and it was compared with dose distribution by using a bolus. Results : The skin surface dose was increased with appling spoiler and decreased by distance of the skin-spoiler separation. The maxium build-up region was 1.5 cm below the skin surface and it was markedly decreased near the skin surface. By using a 1.0-cm thickness spoiler, Dmax moved to 5, 10.2, 12.3 13.9 and 14.8 mm from the skin surface by separation of the spoiler from the skin 0, 5, 10, 15. 20 cm, respectively. Conclusion : The skin surface dose was increased and maximum build-up region was moved to the surface by using a spoiler. Therefore spoiler was useful in treating by high energy photon in the head and neck tumor.