• The Journal of the Acoustical Society of Korea
• /
• v.33 no.3
• /
• pp.191-199
• /
• 2014

Wave reflection and transmission characteristics in waveguides are an important issue in many engineering applications. A combined spectral element and finite element (SE/FE) method is used to investigate the effects of local non-uniformities but limited at relatively low frequencies because the SE is formulated by using a beam theory. For higher frequency applications, a method named a combined spectral super element and finite element (SSE/FE) method was presented recently, replacing spectral elements with spectral super elements. This SSE/FE approach requires a long computing time due to the coupling of SSE and FE matrices. If a local non-uniformity has a uniform cross-section along its short length, the FE part could be further replaced by SSE, which improves performance of the combined SSE/FE method in terms of the modeling effort and computing time. In this paper SSEs are combined to investigate the characteristics of waves propagating along waveguides possessing geometric non-uniformities. Two models are regarded: a rail with a local defect and a periodically ribbed plate. In the case of the rail example, firstly, the results predicted by a combined SSE/FE method are compared with those from the combined SSEs in order to justify that the combined SSEs work properly. Then the SSEs are applied to a ribbed plate which has periodically repeated non-uniformities along its length. For the ribbed plate, the propagation characteristics are investigated in terms of the propagation constant.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.4
• /
• pp.287-292
• /
• 2012

In this study, Multi-Channel Magnetic Flux Leakage(MFL) sensor - based inspection system was applied to monitor the condition of cables. This inspection system measures magnetic flux to detect the local faults(LF) of steel cable. To verify the feasibility of the proposed damage detection technique, an 8-channel MFL sensor head prototype was designed and fabricated. A steel cable bunch specimen with several types of damage was fabricated and scanned by the MFL sensor head to measure the magnetic flux density of the specimen. To interpret the condition of the steel cable, magnetic flux signals were used to determine the locations of the flaws and the level of damage. Measured signals from the damaged specimen were compared with thresholds set for objective decision making. In addition, the magnetic flux density values measured from every channel were summed to focus on the detection of axial location. And, sum of flux density were displayed with threshold. Finally, the results were compared with information on actual inflicted damages to confirm the accuracy and effectiveness of the proposed cable monitoring method.

• Archives of design research
• /
• v.19 no.2 s.64
• /
• pp.73-80
• /
• 2006

The main purpose of this study is to help develop the productional system of the three dimensional digital animation domestically. Many 30 digital animation projects are being developed and finished with foreign computer graphics technology. However, the 3D animation market in Korea is not as good as the ones in other countries. One of the most significant problems is the lack of a program of study in Korea concerning productional systems used to create 3D animation. We previously imported an advanced productional system from the U.S., which was adaptable to big projects, and consequently, expanded the international digital animation market. Now, we need to develop a new production system which is fully adaptable to the Korean market. A non-sequential system of 3D digital animation tailored for small projects is more adaptable to domestic industry than the sequential system known as the 'Pipeline system.' A non-sequential system is good for small productions that are trying to create animation on a limited budget. The workers in this system can learn to make animation fast and effectively. They can also learn how to discuss with the others in order to avoid duplication of action. In contrast, in the Pipeline System, many workers repeat confirmation steps during the process for the same animations. The benefit of the non-sequential system is that the worker's interest and education can speed up production, because he/she can quickly learn every step of the animation process instead of just doing a particular job which does not allow him/her to observe the other steps involved. The 'animatic' step is the most important in the non-sequential system. The final animation is produced from the animatic. It is developed from scratch through to the final product but only after the agreement of all the workers, including a director.

• The Journal of the Korea Contents Association
• /
• v.11 no.6
• /
• pp.135-143
• /
• 2011

Visual effect production by computer graphics techniques has become more important in these days. However, there are three problems in the domestic contents production environments. First of all, most Korean film companies have insufficient generally potential to maintain and support their R&D (Research and Development) teams. Secondly, they are much dependent on the abroad commercial software tools. Finally, many people have to participate in the image production pipeline, called the labor-intensive pipeline. In producing a demonstration work, "The Sixty -miles-an-hour man", we have evaluated the usefulness of the developed camera tracking and image composition methods and then examined various production consideration elements. In addition, in order to develop a productive technical element and write a competitive film script, mutual understanding between the developers and the production users should be achieved. Also, this paper describes a role of the technical supervisor to direct the production environment in detail.

• Journal of Energy Engineering
• /
• v.22 no.4
• /
• pp.362-369
• /
• 2013

Two-phase flow is frequently observed in many industries such as nuclear power plants and oil transportation. Two-phase flow regime depends on the flow rates, the fluid properties and the structure of flow channels. Since the identification of the flow regime is of great importance in the system design and the safety analysis, a number of theoretical and experimental investigations have been performed. This paper presents a basic research on the characteristics of each flow regime and transition boundary in the two-phase flows. The flow regime of the upward air-water flow in the vertical tube, 30 mm in the inner diameter, is distinguished by using the high-speed camera and the Wire-mesh sensor(WMS). The identified experimental data are compared with the flow regime maps proposed by Taitel et al, Mishima and Ishii. Even though there is slight difference in the transition boundary, the experimental data show general agreement with these flow regime maps.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.3
• /
• pp.94-100
• /
• 2021

To improve the productivity of cargo containment construction for a membrane LNG carrier, it is important to shorten the installation period and process of the scaffolding system, which is a construction workbench of a cargo containment for a membrane LNG carrier. As an effective method, opinions are being gathered to enlarge the lifting unit from the existing two stages to eight stages. On the other hand, the stresses around the pin and hole will increase significantly because of the increase in lifting load according to the large size of the module. The purpose of this study was to establish a new large module-lifting plan by introducing TRIZ to solve these problems. This study adopted a method to utilize 40 inventive principles, which is one of the various problem-solving tools of TRIZ. First, technical contradictions were derived, the engineering parameters were selected. Second, efficient inventive principles were selected to overcome the technical contradictions using a contradiction matrix. Finally, the general and specific solutions were derived through the selected inventive principle, and structural analysis confirmed that the stress generated in the structure was low. The utility of TRIZ was confirmed by the successful lifting of large modules using the established lifting method.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.3
• /
• pp.83-97
• /
• 1999

This paper presents the results of a parametric study on the interaction between buried pipes and surface load using the finite element method of analysis. A series of laboratory model tests were also performed in order to validate the adopted finite element model and to capture essential features of the physical behavior of buried pipes subjected to surface load. In the parametric study, a wide range of boundary conditions were analyzed with emphasis on the response of the buried pipes to surface load. The results of analysis such as contact stress distribution at the soil/pipe interface and axial thrust of the pipe were thoroughly analyzed, and a database on the response of buried pipe under surface load was established for future development of a semi-empirical design/analysis method. The results indicated that the degree of interaction between buried pipes and surface load significantly varies with the vertical and lateral location of pipe with respect to surface load, and that the current design method, which does not consider soil-structure interaction, cannot correctly capture the pipe response to surface loading. Furthermore, based on the results of analysis, a semi-empirical equation was suggested, which estimates the maximum pipe thrust due to surface load for flexible buried pipes.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.13 no.3
• /
• pp.187-197
• /
• 2010

Carbon dioxide Capture and Storage(CCS) is regarded as one of the most promising options to response climate change. CCS is a three-stage process consisting of the capture of carbon dioxide($CO_2$), the transport of $CO_2$ to a storage location, and the long term isolation of $CO_2$ from the atmosphere for the purpose of carbon emission mitigation. Up to now, process design for this $CO_2$ marine geological storage has been carried out mainly on pure $CO_2$. Unfortunately the $CO_2$ mixture captured from the power plants and steel making plants contains many impurities such as $N_2$, $O_2$, Ar, $H_2O$, $SO_2$, $H_2S$. A small amount of impurities can change the thermodynamic properties and then significantly affect the compression, purification, transport and injection processes. In order to design a reliable $CO_2$ marine geological storage system, it is necessary to analyze the impact of these impurities on the whole CCS process at initial design stage. The purpose of the present paper is to compare and analyse the relevant physical property models including BWRS, PR, PRBM, RKS and SRK equations of state, and NRTL-RK model which are crucial numerical process simulation tools. To evaluate the predictive accuracy of the equation of the state for $CO_2-SO_2$ mixture, we compared numerical calculation results with reference experimental data. In addition, optimum binary parameter to consider the interaction of $CO_2$ and $SO_2$ molecules was suggested based on the mean absolute percent error. In conclusion, we suggest the most reliable physical property model with optimized binary parameter in designing the $CO_2-SO_2$ mixture marine geological storage process.

• Proceedings of the Mineralogical Society of Korea Conference
• /
• 2001.06a
• /
• pp.115-115
• /
• 2001

경주시 양남면의 4기 단층으로 추정되는 수렴단층에 의해 절단되는 해안단구 퇴적층 풍화단면에서 저결정질 광물인 앨로패인 교결층을 기재하였다. 이들은 자갈퇴적층 내에 협재하는 수조의 모래층에 한정되어 형성되어 있으며, 3-17 cm 두께로 연장성이 매우 좋다. 편광현미경 관찰에 의하면 모래층에는 사장석편들이 다량 함유되어 있으며 앨로패인은 광학적 등방성의 치밀한 점토집합체들로서 사장석 입자를 선택적으로 교대하거나 자갈과 모래입자들을 피복하고 있다. 앨로패인은 광학적 이방성인 상하위층의 고령토질 점토피복물과 명확히 구분된다. 앨로패인의 전자현미분석에 의하면, Al/Si 원자비가 1.3-1.7 범위이고 평균값은 1.5이다. X선회절분석 결과 3.49$\AA$과 2.26$\AA$에서 두 개의 넓은 회절대가 관찰된다. 주사 및 투과전자현미경관찰에 의하면 앨로패인을 특정한 입자형태 없이 치밀한 겔상태를 이루고 있다. 열분석에 의하면 96$^{\circ}C$에서 큰 흡열피크와 992$^{\circ}C$에서 발열피크가 관찰되며, 총 45% 정도의 중량감소를 보인다. 사장석의 평균조성은 An$_{87}$이며, 사장석내 유리포유물의 전자현미분석결과는 화산암 화학분류도에서 현무암 영역에 도시된다. 이 지역의 기반암은 현무암질 라필리응회암이나 사장석편을 제외하고 벤토나이트화되어 있다. 따라서 해빈환경에서 사장석이 벤토나이트에서 분리되어 퇴적한 것으로 보인다. 앨로패인 교결층은 해수면 강하로 단구퇴적층이 지표로 노출된 후, Al의 함량이 높고 비교적 풍화에 약한 사장석이 선택적으로 풍화되어 생성되었다. 앨로패인으로 피복된 모래층 내의 자갈은 풍화반응이 지체되어 상하위층의 자갈과 비교하여 풍화도에 있어서 현저한 차이를 보인다.. 파이프 중심에서 외곽부로 갈수록 전기석의 함량은 줄어들고 있고 장석들이 알바이트ㆍ칼스베드 쌍정을 보이며, 흑운모가 각섬석보다는 우세하게 나타나고 있다. 전기석은 주상 결정, 자형 내지 반자형의 입자로 다색성을 보이며, 결정 중심에서 가장자리로 갈수록 파란색과 황갈색의 광학적 누대구조를 관찰할 수 있다. 일광광산에서 산출되는 전기석에 대한 현미경 관찰은 열수기원임을 지시하고 있다. 야외조사와 현미경 관찰의 예비조사에 의하면 일광광산의 전기석이 형성된 환경은 다른2가지 화학적인 저장소의 혼합 효과의 결과로 생성되어진 것으로 예상된다. 일광의 화강암류를 만든 마그마는 전기석을 형성할 만큼의 Fe-Mg성분이 충분하지 않았을 것이다. 화강암 내에 흑운모와 각섬석의 결정작용에 의해 마그마의 Fe-Mg성분이 고갈되어지고 이로 인해 그 함량이 감소하며 상대적으로 마그마 내에 남은 붕소(B$_2$O$_3$)는 열수로 용리되고 흑운모, 각섬석과 평형을 유지하며 열수에 남아있게 된다. 잔류용융체에 남은 붕소의 함량은 전기석을 만들기에 충분함에도 불구하고, Fe-Mg 함량이 부족하여 마그마 기원의 전기석 결정을 만들 수가 없다가 광맥이 형성된 시기에 또 다른 열수가 공급되면서 이전의 평형이 깨지고 기존의 흑운모와 같은 염기성 광물이 붕소(B)를 함유한 새로운 열수와 반응하여 전기석을 형성한 것으로 예상한다. 앞으로 전암과 광물에 대해 지화학적 연구를 통해 화강암류와 전기석과의 지화학적 연관성, 주성분 원소와 열수의 특성과의 상관관계, 전기석의 기원(마그마 기원인지 열수기원인지)이 보다 정확하게 파악될 것이다. 마그마 진화에 따른 전기석의 성분변화와 기원을 이용하여 일광광산의 동광화대를 형성한 마그마 계에서 열수계로 이어지는 지질학적 과정을 이해할 수 있을 것이며, 암석 성인론적 지시자로서

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.11 no.4
• /
• pp.191-198
• /
• 2008

To design a reliable $CO_2$ marine geological storage system, it is necessary to perform numerical process simulation using thermodynamic equation of state. $CO_2$ capture process from the major point sources such as power plants, transport process from the capture sites to storage sites and storage process to inject $CO_2$ into the deep marine geological structure can be simulate with numerical modeling. The purpose of this paper is to compare and analyse the relevant equations of state including ideal, BWRS, PR, PRBM and SRK equation of state. We also studied the effect of thermodynamic equation of state in designing the compression and transport process. As a results of comparison of numerical calculations, all relevant equation of state excluding ideal equation of state showed similar compression behavior in pure $CO_2$. On the other hand, calculation results of BWRS, PR and PRBM showed totally different behavior in compression and transport process of captured $CO_2$ mixture from the oxy-fuel combustion coal-fired plants. It is recommended to use PR or PRBM in designing of compression and transport process of $CO_2$ mixture containing NO, Ar and $O_2$.