• Tunnel and Underground Space
• /
• v.13 no.6
• /
• pp.444-454
• /
• 2003

Rock fragmentation technique by cutter penetration has widely been used in the mechanical tunnel excavation. Microcracks propagate and interact because of locally concentrated high stress induced by cutter penetration. which is caused by heterogeneity of rocks. In this study Weibull distribution function and degradation index are used to consider the strength heterogeneity of a rock and the degradation of rock properties after failure. Through the numerical analyses, it is shown that the lateral pressure has an important influence on the rock fragmentation. In the single cutter penetration, large chips are formed as lateral pressure increase. The cutter spacing is also an important factor that affects the rock fragmentation in the double cutter penetration. The fragmentation efficiency of the double cutter penetration is better when cutter spacing is 70 mm than 40 mm and 100 mm. From the results, it is expected that this study can be applied to a TBM tunnel design by understanding of chipping process and mechanism of rock due to cutter penetration.

• Tunnel and Underground Space
• /
• v.24 no.4
• /
• pp.325-333
• /
• 2014

Hydraulic fracturing is the key technology for production of shale gas, which is one of the major unconventional resources. Brittleness index is one of the most important mechanical properties which determine the efficiency of hydraulic fracturing. It was required that the production of shale gas increases with more brittle behavior. Confusingly, there are numerous definitions available for brittleness of rock. This paper summarizes various definitions of brittleness index, and presents correlation analysis of the brittleness indices by using the laboratory experimental results of 48 shale specimens in Korea. Generally, it shows a very weak positive correlation between the brittleness index ($B_1$) which is the ratio of uniaxial compressive strength to tensile strength and the brittleness index ($B_3$) which is calculated by using the Youngs modulus and Poisson's ratio. In addition, the role of Poissons ratio is not clear in defining brittleness indices. In conclusion, standardization of definition for brittleness index is required to apply it to hydraulic fracturing as a parameter for predicting the efficiency.

• Tunnel and Underground Space
• /
• v.31 no.6
• /
• pp.520-533
• /
• 2021

It is necessary to increase the blasting efficiency in order to minimize the economic loss caused when the excavation cross section is reduced due to the stability problem of underground mining development, and for this, a new blasting design is proposed. In this study, the blasting efficiency of the general design in the field, the suggestion designI, which added two columns to production blasting, and the suggestion design II, which added one column to create asymmetry, is compared. Advance rate and fragmentation were selected as the evaluation index of the blasting efficiency. In the case of advance rate, compared to the normal, the suggestionI improved by 6.07% and the suggestionII improved by 4.65%. In the case of fragmentation, based on P80, compared to the normal, the suggestionI reduced about 58% and the suggestionII was about 47%. Accoording to the evaluation index, the suggestion designI shows better blasting efficiency than the suggestion designII. But considering the additional work time and cost required for the suggestion designI due to the insignificant difference in the evaluation index results, the asymmetry V-cut, the suggestion designII, is judged to be a more suitable blasting design for the site.

• Korean Journal of Soil Science and Fertilizer
• /
• v.32 no.3
• /
• pp.254-260
• /
• 1999

This experiment was carried out to evaluate the effect of improvement of soil physical property such as deep plowing and chiseling and diagnostic application of N, P, K fetilizers. Latex Coated Urea(LCU), compost, sillicate for increasing yielding and enchancing N-use efficiency in puddled-soil drill seeding of Rice. The soil physical properties, such as bulk density, hardness and porosity were increased by deep plowing and chiseling, as well as chemical propeties were highly enhanced soil productivity due to increase the content of organic matter, available $P_2O_5$ and K as compare with control. The amount of $NH_4-N$ in soil was highly increased by diagnostic fertilization and chiseling, while recovery rate of V fertilizer was the highest at LCU 80% applied with chiseling. The rice yield increased by 23% under the diagnositic application of LCU 80% applied base with chiseling.

• Journal of Korea Foundry Society
• /
• v.41 no.2
• /
• pp.132-138
• /
• 2021

In this study, the power basic units to produce cast iron by using the press and shredded scrap are compared in 16t/h low-frequency induction melting furnace. Charging the shredded scrap instead of the press scrap was confirmed that the power basic unit is improved by about 5%. The energy characteristics according to the shape and size of scrap steel and the effect of the furnace size were investigated. Finally, the strategy to improve the utilization of this technology was proposed.

• Explosives and Blasting
• /
• v.37 no.3
• /
• pp.34-42
• /
• 2019

An electronic initiation system that can support various types of field blasting works has been developed and put into practice. The newly developed equipment called Hanwha Electronic Blasting System (HEBS) II has three basic operation modes of scanning, logging, and tagging, among which the blaster can choose the most suitable one for the specific site conditions. In the present study, the work efficiency of the system in the scanning, logging and tagging modes was compared with that of the previous non-electric detonator. The results were estimated based on the aspects of the ground vibration, fragmentation, and digging time. It was found that the ground vibration, fragmentation, and digging time of the new system were decreased by about 45%, 31%, and 13%, respectively, with respect to the previous system. This result confirms that the new system is very efficient in the scanning, logging and tagging modes under the field conditions.

• The Journal of Engineering Geology
• /
• v.32 no.4
• /
• pp.725-733
• /
• 2022

This study applied a hydraulic rock splitting system equipped with a hybrid packer to the bench-cut method. The hybrid packer system is an improvement of the packer developed in previous studies; it is designed efficiently to reduce vibration and noise during rock excavation by combining the two functions of inducing hydraulic fractures using injection pressure and then expanding and extending them using a rubber packer. Field experiments assessed the efficiency of rock excavation with respect to the injection conditions; the adjusted experimental conditions included the distance from the free surface and the test holes drilled at the top of the slope and the injection settings. Using a separation of 5 m left some unexcavated parts, but using a separation of 1 m left no unexcavated parts. The hydraulic fractures generated by the injection pressure developed generally parallel to the free surface and expanded and extended as the rubber packer expanded, thus facilitating bench-cut excavation. For hydraulic rock splitting to be broadly applicable to bench-cut rock excavation, it is important to accumulate results from many field experiments conducted under varying experimental conditions for various types of rockmass.

• Tunnel and Underground Space
• /
• v.16 no.2 s.61
• /
• pp.156-165
• /
• 2006

Already, vari-stem, gas-bag, power deck, air ball etc. are used by various blasting methods to take the advantage of air decking technology in abroad. Air tube product has been used continuously in domestic and air ball product was made recently. In the case study, we analyzed about the application and the effect or air deck blasting method in domestic blasting area. As results or this case study, it was shown that blasting vibration was decreased about $21{\sim}41%$ and quantities or explosives was decreased about $17{\sim}30%$. Also, in the case of using air deck blasting method, fragmentation was shown to be smaller than common blasting method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.481-484
• /
• 2008

Recently, the recycling and reusing of construction and demolition waste concrete is urgently required because waste concrete is greatly increased according to the rapid increasing of urban redevelopment project, but the problem solution for demand and supply unbalance of fine aggregate is urgently required because of the restriction of collecting sea fine aggregate. So the utilization of high quality recycled fine aggregate using construction and demolition waste concrete as new fine aggregate for construction industry is urgently. Accordingly, In this study, As recycled fine aggregate manufacturing technology with exceeding in economical efficiency, reduction efficiency of environmental load and quality improvement effect of recycled fine aggregate, it is to develop dry manufacturing system composed specific gravity separator of high-speed rotation impact type and centrifugal Force Powder Collector, etc. And it is to examine mechanism of recycled sand dry manufacturing system.

• Journal of Korea Foundry Society
• /
• v.41 no.1
• /
• pp.11-15
• /
• 2021

Scrap steel used as a charge material in melting process of cast iron foundry is mostly press scrap. The press scrap usually causes several problems including energy loss, workability, safety, and so on. By charging the shredded scrap instead of the press scrap, it is expected that the above-mentioned problems can be solved. In this study, the power basic units to produce cast iron by using the press and shredded scrap are compared in 3t/h medium-frequency induction melting furnace. Charging the shredded scrap instead of the press scrap was confirmed that the power basic unit is improved by about 15%. The characteristics and restrictions of the usage according to the shape and size of scrap steel were considered.