• 제목/요약/키워드: 파괴양상

Search Result 572, Processing Time 0.026 seconds

Fractographic Studies in Ballistically Damaged Polycrystalline Alumina (탄도충격으로 파괴된 다결정 Alumina의 파면조직)

  • 김종희
    • Journal of the Korean Ceramic Society
    • /
    • v.15 no.3
    • /
    • pp.127-134
    • /
    • 1978
  • 탄도충격에 의하여 파괴된 단결정 alumina의 파면조직을 광학 및 투과 전자현미경으로 연구 분석하였다. 파면의 주된 파괴 양상은 결정 입개면의 분리 또는 결정입내 파괴로 구성되어 있고 이러한 파괴과정은 복잡한 cleavage 양상과 결정입자 내에서의 소성변형을 수반하고 있다. 미세조직 관찰 결과에 의하면 alumina ceramics의 충격 파괴과정에서 에너지의 흡수가 국부적인 소성변형으로 나타나고 있음을 알 수 있었다.

  • PDF

A Numerical Simulation for the Dam-Break Wave from the Hypothetical Failure of Soyanggang Dam (소양강댐 가상 파괴파의 수치모의)

  • Lee, Sang Ho;Lee, Kil Seong
    • KSCE Journal of Civil and Environmental Engineering Research
    • /
    • v.12 no.2
    • /
    • pp.109-122
    • /
    • 1992
  • With the uncertainty of breaching mechanism, channel roughness, and elevation-discharge relationship at the downstream dam sites, the dam break wave from the hypothetical failure of Soyanggang dam is routed by DAMBRK. Simulation results show that lower region of Seoul will be flooded in 6~8 hours which has the elevation lower than 30~20m, and most part of Chuncheon will also be flooded. The peak discharge becomes approximately 70,000 CMS at Indogyo, and 220,000~340,000 CMS at Chuncheon. Sensitivity analysis shows that the inundation feature of Seoul will hardly be affected by the failure of downstream dams.

  • PDF

Theoretical Assessment of Limit Strengthening Ratio of Bridge Deck Based on the Failure Characteristic (교량 바닥판의 파괴형태를 고려한 임계보강재비의 이론적 산정)

  • 심종성;오홍섭;유재명
    • Journal of the Korea Concrete Institute
    • /
    • v.14 no.1
    • /
    • pp.110-117
    • /
    • 2002
  • In a strengthened bridge deck which received increased service loads, failure patterns of bridge deck vary depending on deck thickness, compressive strength of concrete, yielding strength of reinforcement, reinforcement ratio and additional strengthening ratio. General failure pattern that is most commonly reported as punching shear failure after the main rebar yields, followed by yielding of distributing rebar. In this paper, by Proposing a limit to the amount of strengthening material, a brittle failure can be prevented and a ductile failure mode similar to that developed in unstrengthened deck is derived. In order to calculated the limit strengthening ratio, the yield line theory and previously proposed plastic punching shear model have been used

Monitoring of Cut-Slope Behavior with Consideration of Rock Structure and Failure Mode (개착사면의 구조적 특성과 파괴양상을 고려한 계측 해석)

  • Cho, Tae-Chin;Park, So-Young;Lee, Sang-Bae;Lee, Geun-Ho;Won, Kyung-Sik
    • Tunnel and Underground Space
    • /
    • v.16 no.6 s.65
    • /
    • pp.451-466
    • /
    • 2006
  • Analysis of slope behavior concerning the structural characteristics of field rock mass can be processed by virtue of borehole information of joint orientation and position acquired from DOM drilled core. Anticipated sliding potential of pre-failed rock slope is analyzed and the regional slope instability is investigated by inspecting the hazardous joints and blocks the traces of which is projected on the cut-face. Cross section has been set at the center of rock slope and the traces of both joints and tetrahedral blocks, which potentially can induce the slope failure, are drawn to investigate the failure modes and the triggering mechanism. Automated monitoring system has been established to measure the slope movement and especially, inclinometer has been installed inside DOM borehole to analyze the slope movement by considering the internal rock structure. Algorithms for predicting the slope failure time have been reviewed and the significance of heavy rainfall on the slope behavior has been investigated.

Failure Mechanism and Ultimate Strength of Headed Bar Anchored in Deep Beam Using Truss Models (트러스 모델을 이용한 춤이 깊은 보에 정착된 헤드 철근의 파괴 메커니즘과 극한 내력 해석)

  • Cheon, Sung-Chul;Hong, Sung-Gul
    • Proceedings of the Korea Concrete Institute Conference
    • /
    • 2005.05a
    • /
    • pp.143-146
    • /
    • 2005
  • 최근 들어 90도 표준갈고리의 대안으로 정착판을 지니는 헤드 철근(headed bar)에 대한 관심이 높아지고 있다. 헤드 철근의 정착내력은, 정착판의 지압력과 위험단면에서 헤드까지 정착길이의 부착력으로 발현된다. 실제 구조물에서는 정착되는 부재의 재료 및 기하학적 물성에 의해 다양한 파괴가 발생된다. 따라서 헤드 철근의 정착내력은 단순히 지압력과 부착력의 합으로 산정될 수 없으며, 발생 가능한 모든 파괴양상을 고려한 최소 내력으로 결정되어야 한다. 헤드 철근의 정착내력을 산정하기 위한 기본적인 해석모델로, CCT 절점에 정착된 헤드 철근의 트러스 모델을 제안하였다. 제안된 트러스 모델의 파괴는 부착파괴와 콘크리트의 압축파괴로 구분되며, 재료 및 기하학적 물성에 의해 파괴 양상이 결정된다. 이러한 트러스 모델은 외부 보-기둥 접합부와 같이 보다 복잡한 부위에 정착된 헤드철근의 정착 기구를 설명하는데 활용될 수 있다.

  • PDF

Numerical Analysis of Load Bearing Behavior of Shallow Foundations (얕은기초의 하중지지거동에 관한 수치해석)

  • Lee, Seung-Hyun;Lee, Su-Hyung
    • Journal of the Korea Academia-Industrial cooperation Society
    • /
    • v.15 no.10
    • /
    • pp.6322-6328
    • /
    • 2014
  • Finite element analyses were performed to find out the load bearing behavior of three kinds of shallow foundations. The analysis results for strip footing showed that local shear failure mode could be observed for a zero dilatancy angle and general shear failure mode could be seen for non-zero dilatancy angles. The ultimate bearing loads for non-zero dilatancy angles were approximately 1.5 times higher than that of a zero dilatancy angle. General shear failure mode was observed for circular footing and square footing regardless of the dilatancy angle. The ultimate bearing loads for a non-zero dilatancy angle were slightly greater than that for a zero dilatancy angle. A comparison of the load-settlement curves for three kinds of footing showed that the load bearing capacities for non-zero dilatancy angle were greater than those for a zero-dilatancy angle.

Structural Behavior of Polymer Mortar Sandwich Panels with Simply Supported Four Edges (4변이 단순지지된 폴리머 모프터 샌드위치 패널의 구조적 거동)

  • 연규석;김광우;김기성;황진용
    • Magazine of the Korea Concrete Institute
    • /
    • v.5 no.1
    • /
    • pp.145-155
    • /
    • 1993
  • 본 연구에서는 표면부를 에폭시 폴리머 모르터로 하고 , 중심부를 발포 폴리스티렌으로 하는샌드위치 패널을 제조하여, 표면부를 용접철강으로 보강한 경우와 보강하지 않은 경우에 대하여 4강 단순지지 조건에서의 정적 차 통해 하중-처짐, 휨모멘트-변형률, 파괴양상 등을 구명하였다. 단위중량, 극한가중, 휨모멘트는 중심부의 두께보다 표면부 두께에 더 큰 영향을 받으며 극한처짐은 보강안된 경우 표면부 보다 중심부 두께의 영향이 월등히 컸으마 보당된 경우는 표면부나 중심부 두께의 영향이 비슷하였다. 그러나 용접철망의 보강은 샌드위치 패널의 처짐억제 보다 인성증가에 기여도가 높은 것으로 나타났다. 샌드위치 패널의 파괴양상은 보강하지 않은 경우 선형파괴가 일어난데 비해 보강한 경우에는 방사상의 파괴가 일어났다.

Structural Behavior of RC Beams Strengthened with Steel Plates (강판 휨보강된 철근콘크리트보의 구조적 거동)

  • 오병환;조재열;강동옥
    • Magazine of the Korea Concrete Institute
    • /
    • v.9 no.5
    • /
    • pp.233-244
    • /
    • 1997
  • 구조적으로 손상을 입은 구조물들에 대한 보강방법으로 강판, 카본쉬트, 아라미드섬유쉬트 등을 이용한 접착공법이 최근 들어 많이 사용되고 있으며 그 중 가장 널리 Tm이는 방법은 강판접착공법이다. 강판접착공법에 대해서는 많은 연구가 진행되어 오고 있으나, 보의 구조적 거동에 영향을 미치는 다양한 인자들의 영향이나 강성, 파괴양상등에 미치는 영향들에 대해서는 체계적인 평가가 이루어지지 않은 실정이며 특히 강판접착공법에서 파괴에 큰 영향을 미치는 박리하중에 대한 연구는 미흡한 실정이다. 따라서 본 연구에서는 일련의 철근콘크리트보부재를 대상으로 하여 주요실험변수로 선행하중의 크기, 강판의길이, 강판의 두께, 앵커볼트의 간격과 유무, 강판의 층수, 측면보강높이를 실험변수로 하여, 휨인장에 대해 강판잡착공법을 적용하여 포괄적인 실험을 수행하였다. 3등분점하중법의 실험결과를 이용하여 처짐, 인장 및 압축 철근의 변형도, 콘크리트와 강판의 변형도를 분석하였고, 이를 토대로 파괴양상과 파괴하중을 분석하였다.

A Study on Blasting Aspect of Steel Member and Concrete Member According to Separation distance of Explosives (폭약 이격에 따른 강판과 콘크리트 부재의 파괴양상 연구)

  • Yang, Hyung-Sik;Kim, Jung-Gyu;Ko, Young-Hun;Noh, You-Song;Shin, Myeong-Jin
    • Explosives and Blasting
    • /
    • v.32 no.1
    • /
    • pp.1-9
    • /
    • 2014
  • TNT was blasted on the surface of steel plates and concrete block to study the effect of separation distance between object and charge. The equation of US Army Corps of Engineers turned out to be rather conservative. Effect of separation distance is larger for steel plate than concrete block. Steel plate cannot be cut by standard or more charge in the case of 2 cm separation while the concrete block can be crushed with the same distance.

기초, 굴착

  • 정교철;오대열
    • Proceedings of the KSEG Conference
    • /
    • 2004.03a
    • /
    • pp.24001-24056
    • /
    • 2004
  • 암반 기초에서 발생 가능한 파괴형태로는 $\circled1$전단파괴(Shear failure) $\circled2$관입파괴(punch failure) $\circled3$붕락(Collapse) $\circled4$균열파괴 (cracking) $\circled5$분쇄상파괴 (crushing) $\circled6$쐐기상파괴 (wedging)를 들 수 있다. 그림 2.4-1에서 (a)는 연암층 내에서의 전형적인 전단파괴를 나타내고, (b)는 소성암반 상부에 강성암반이 놓였을 때의 전단파괴를 보여준다. (c)는 2층으로 구성된 지반에서의 전단파괴 양상이며, (d)는 편심하중이 작용할 때의 전단파괴이다. (e)는 사면 상에서의 활동에 의한 파괴유형이다. (f)는 절리가 발달한 풍화된 암반내로 진행되는 관입파괴를 보여주고 있다. (e)는 연암지반 내부로 강성암반이 관입되어 파괴된 모습이다. (h)는 풍화된 화강암에서의 관입파괴 유형이다. (i)는 석회암층 내부의 지하공동에 의한 붕락현상을 보여주고 있으며, (j)는 지하수의 유동에 의해 형성된 공동으로 인한 붕락파괴를 나타낸다. (k)는 균열파괴, (l)은 분쇄상 파괴, (m) 쐐기상 파괴, (n)은 단층선을 따른 파괴 유형이다. (중략)

  • PDF