• The Journal of Engineering Geology
• /
• v.34 no.2
• /
• pp.317-327
• /
• 2024

When a non-persistent joint system is formed in a large-scale rock slope, slope failure may occur due to presence of a the stepped sliding surface. Such a surface can be divided into joint-to-joint sliding surfaces or joint-to-rock bridge sliding surfaces. In the latter case, the rock bridge provides shear resistance parallel to the joint and tensile resistance perpendicular to the joint. The load of the sliding rock can lead to failure of the rock bridge, thereby connecting the two joints at each ends of the bridge and resulting in step-path failure of the slope. If each rock bridge on a slope has the same length, the tensile strength is lower than the shear strength, resulting in the rock bridges oriented perpendicular to the joint being more prone to failure. In addition, the smaller the ratio of discontinuity spacing to length, the greater the likelihood of step-path failure. To assess the risk of stepped sliding on a rock slope with non-persistent joints, stability analysis can be performed using limit equilibrium analysis or numerical analysis. This involves constructing a step-path failure surface through a systematic discontinuity survey and analysis.

• Journal of the Korea Concrete Institute
• /
• v.16 no.1 s.79
• /
• pp.10-17
• /
• 2004

Shear tests were performed on four ends of full scale U-type beams which were designed by optimum process for the depth with a live load of 4903Pa. The ratio of width to depth of full scale 10.5 m-span, composite U-type beams with topping concrete was greater than 2. Following conclusions were obtained from the evaluation on the shear performance of these precast prestressed beams. 1) Those composite U-type beams performed homogeneously up to the failure load, and conformed to ACI Strength design methods in shear and flexural behaviors. 2) The anchorage requirements on development length of strand In the ACI Provisions preyed to be a standard to determine a failure pattern within the limited test results of the shallow U-type beams. 3) Those all shear crackings developed from the end of the beams did not lead to anchorage failure. However, initiated strand slip may leads the bond failure by increasing the size of diagonal shear crackings. 4) The flexural mild reinforcement around the vertical center of beam section was effective for developments of a ductile failure.

• Journal of the Korea Concrete Institute
• /
• v.22 no.5
• /
• pp.675-684
• /
• 2010

The reinforced concrete members are designed to fail in flexural to lead ductile fracture. In the building structures, the failure is typically imposed on beams to prevent damages in columns. However, progression of plastic collapse mechanism may ultimately develop, a plastic hinge at the bottem end of the first floor column, which then can be subjected to shear or bond finally due to large axial force and small shear span-to-depth ratio. In this study, 10 RC column specimens failed in shear after flexural yielding was investigated to determine the factors affecting the plastic hinge length. The findings of this study showed that the most effective factor affecting the plastic hinge length was an axial force. As an axial force increase, an axial strain and a ductility ratio were decreased obviously. The test also shows the observed plastic hinge length was about 0.8~1.2d and the this result has difference compared with forward research.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.5A
• /
• pp.485-493
• /
• 2010

GFRP rebar with ribs resemble those of deformed steel rebar was developed in 2005. It was reported that ribs of the GFRP rebar were sheared off due to the lower shear strength of polymer. In this study, the basic development length of the GFRP rebar was investigated through pull-out tests, models specified in ACI440.1R-03 and -06, and empirical model derived by Cosenza et al. (2002). As a results of pull-out tests, the critical embeddment length, which is defined as the length when failure mode is changed from pull-out to bar fracture, was 20 times of bar diameter for GFRP rebar and was 15 times for steel rebar. It is believed that the basic development of the GFRP rebar is 21 times of bar diameter, which is determined from the application of average bond strength into the model equation specified in ACI440.1R-03. Compared to the model equation in ACI440.1R-06, that in ACI440.1R-03 is recommendable for design purpose. The Cosenza et al.'s model underestimates the basic development length of the GFRP rebar.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.25-25
• /
• 2021

점착성 유사는 비점착성 유사에 비해 1차입자의 크기가 작아 1차입자간의 점착력이 중요한 역할을 하는 유사를 말한다. 점착성 유사는 비점착성 유사에 비해 크기가 작아 입자의 전자기적 점착력의 영향을 무시할 수 없으므로 점착력으로 인해 입자들은 서로 응집하는 동시에 입자들 간의 충돌에 의하여 파괴되는 과정을 거친다. 이러한 응집과 파괴가 지속되는 일련의 과정을 응집현상이라 한다. 점착성 유사는 응집과정을 통해 일차입자보다 크기가 크며 수십 개에서 수천 개의 일차입자와 물의 덩어리인 플럭을 형성하게 된다. 흐름 내 존재하는 플럭의 응집현상에 가장 지배적인 영향을 미치는 인자로 난류 거동이 알려진 바 있다. 본 연구에서는 난류 거동에 따른 점착성 플럭의 입도분포 변화를 살펴보고자 하였으며, 점착성 유사 입도분포 모형을 개발하였다. 수치모형의 개발은 확률과정(또는 추계과정)의 개념을 바탕으로 한다. 점착성 유사의 응집현상을 구성하는 응집과정은 다양한 연구를 통해 메커니즘들이 규명된 것과 달리 파괴과정은 난류로 인해 발생하며 무작위한 것으로 여겨진다. 무작위한 플럭의 파괴과정을 확률과정으로 가정하고 매개변수 중 하나를 대수정규분포를 따르는 난수로 고려하였다. 개발된 모형의 검증은 연안지역에서 점착성 플럭의 거동을 측정한 연구결과와의 비교를 통해 수행하였으며, 흐름 유속의 연직분포와 유사 농도의 연직분포, 응집현상 이후 플럭의 평형크기와 입도분포가 모두 합리적으로 계산되는 것이 확인되었다. 더불어 모의 결과에서는 대수정규분포를 따르는 동일한 난수를 적용하였음에도 불구하고 하상으로부터 거리가 가까워짐에 따라 플럭입도분포가 단봉분포(Unimodal Distribution)와 이봉분포(Bimodal Distribution)가 모두 계산되는 것으로 나타났다. 이는 모형의 개발과정에서 플럭의 가능 최대 크기를 콜모고로브 길이규모로 제한한 것과 관련이 있다. 난류 흐름 내 존재하는 플럭의 크기가 응집현상을 통해 난류의 콜모고로브 길이규모까지 성장하는 경우, 난류의 전단응력이 급격하게 증가하여 파괴과정이 활발해지고 응집과정이 저하된다는 것은 널리 알려진 사실이다. 이러한 사실을 바탕으로 플럭의 가능최대 크기를 콜모고로브 길이규모로 제한하였으며, 하상으로부터의 거리에 따라 콜모고로브 길이규모의 변화로 인해 콜모고로브 길이규모 부근에서 하나의 최빈값이 추가로 나타나는 것으로 이해된다. 수치모의 결과로부터 얻어진 콜모고로브 길이규모와 입도분포 형태의 상관관계를 보다 정확하게 이해하기 위해 실측 자료들을 검토해 본 결과, 균질한 재료를 이용한 실험실 실험결과에서 플럭 이봉분포의 최빈값이 콜모고로브 길이규모와 일치하는 것이 확인되었다. 연안지역에서 측정을 수행한 자료들에서도 이봉분포 또는 다봉분포와 콜모고로브 길이 규모와의 상관성을 찾아볼 수 있었다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.5
• /
• pp.28-33
• /
• 2001

This paper describes the effect of various conditions of the ribs on the breakdown characteristics when metal particle is attached to the spacer in GIS. More improved spacer shape in breakdown characteristics than conventional one is proposed by comparing the results acquired by varying location, length and thickness of the ribbed spacer. As a result, it was found that the electrical breakdown characteristics of the spacer with two ribs were generally better than that with only one rib or no ribs, and it was dependent on the rib length and rib thickness. Especially, it was also confirmed that the electrical breakdown characteristics were more improved by rounding the rib edge.

• Tunnel and Underground Space
• /
• v.20 no.3
• /
• pp.217-224
• /
• 2010

Three relatively homogeneous granitic rocks were studied to investigate the relationship between their microstructural properties and fracture toughness. Fracture toughness and ultrasonic velocity were varied with the orientation of mineral's long axis and microcrack, obtained from optical microscope. The lowest fracture toughness values are obtained, when the fracture propagates parallel to weakness planes which have the orientation of mineral's long axis and microcrack, in other words, when weakness planes develop perpendicular to the direction of tensile stress agrees with that of rift plane. The fracture toughness values, measured with the short rod method, varied from 1.63 to 2.62 MPa $m^{0.5}$, and their values are related with the average grain size and average microcrack length.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.23 no.1
• /
• pp.54-62
• /
• 2019

In this paper, a stress-strain model for high-strength confined concrete is proposed using compressive fracture energy. In the compression test performed by author in Reference [6], an acrylic bar with strain gauges was embedded in the center of the specimen to measure the local strain distribution. It was found from the test that the local strain measurement by this acrylic rod is very effective. The local fracture zone length was defined based on the local strain distribution measured by the acrylic rod. Specifically, it was defined as the length where the local strain increases more than twice of the strain corresponding to maximum stress. In addition, the stress-strain relationship of confined concrete with compressive fracture energy is proposed on the assumption that the amount of energy absorbed by the compressive members subjected to the given lateral confining pressure is constant regardless of the aspect ratio and size. The proposed model predicts even results from other researchers accurately.

• Journal of the Korean Society for Railway
• /
• v.15 no.3
• /
• pp.266-271
• /
• 2012

This study was carried out for the purpose of improving driving safety and comfort of the railways quickly becoming popular. To conducted gas pressure welding to ensure the strength safety of continuous welded rail and rotating bending test tensile test was conducted. The element to determine the tensile strength of gas pressure welds at experiments be attributed to more upsetting length than pressure, according to increases of upsetting length, from brittle fracture to ductile fracture was observed. Through the biopsy of the fracture surface, according to the presence of brittle fracture could be evaluated to strength safety. In addition, mechanical strength of gas pressure welding depending on changes in upsetting length was different. Rotary bending test results were obtained to the infinite life according to exhibited higher fatigue limit of 373MPa at upsetting length 25mm.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.4
• /
• pp.431-442
• /
• 2013

Most of previous studies have insufficiently investigated the shear behavior and fracturing characteristics, experimentally in respect to the change of size of tooth-shaped surface asperity such as length and slope angle in a broad range. This study investigates the influence of the length and slope angle of a tooth-shaped surface asperity on the fracturing characteristics and the interface shear strength by using direct shear test apparatus. A total of 36 interface direct shear tests were conducted by changing the three types of slope angle of surface asperity, four type of length, and three types of normal stress. The shape of fractured surface after the test was quantified by using a three-dimensional surface roughness measurement apparatus. Through the experimental test results, the characteristics of fractured shape of surface asperity according to the normal stress were investigated. In addition, fractured length and height were quantified at each slope angle of surface asperity under a certain normal stress condition.