• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.9
• /
• pp.863-871
• /
• 2013

Flow characteristics of velocity-control trim in a valve is investigated numerically with high pressure drop. A basic trim widely used for a valve in domestic powerplants is selected and designed for a baseline of velocity-control trim. The numerical analysis is focused on flow rate and cavitation with the basic trim. For a condition of high-pressure drop, pressure drop between inlet and outlet and fluid temperature are selected to be 18.1 MPa and $160^{\circ}C$, respectively, which are typical ones considering operating conditions adopted in powerplants. With this baseline model and condition, design changes are made for improvement of flow rate and cavitation phenomenon. For re-design, trim is divided into three zones in radial direction and design parameters of flow area, stage, and flow direction are considered in each zone. With these combined parameters applied to each zone, 4 models with design changes are proposed and their flow rates and cavitation areas are investigated. From comparison with those in the baseline model of a basic trim, proposed models show better performance in both flow rate and cavitation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.49 no.12
• /
• pp.1011-1018
• /
• 2021

This numerical study conducts the modeling and the hover performance analyses of coaxial co-rotating rotor(or stacked rotor), using a rotorcraft comprehensive analysis code, CAMRAD II. The important design parameters such as the index angle and axial spacing for the coaxial co-rotating rotor are varied in this simulation study. The coaxial co-rotating rotor is trimmed using the torque value of the upper rotor of the previous coaxial counter-rotating rotor or the total thrust value of the previous coaxial counter-rotating rotor in hover. The maximum increases in the rotor thrust is 1.84% for the index angle of -10° when using the torque trim approach. In addition, the maximum decreases in the rotor power is 4.53% for the index angle of 20° with the thrust trim method. Thus, the present study shows that the hover performance of the coaxial co-rotating rotor for e-VTOL aircraft can be changed by the index angle.

• Proceedings of KOSOMES biannual meeting
• /
• 2018.06a
• /
• pp.145-145
• /
• 2018

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.192-195
• /
• 2008

A sensor fault detection method for small turbo shaft engine considering multiple trim conditions is proposed. This engine is used in a helicopter. Firstly, under multiple trim conditions, we derive the linearized models from a nonlinear model which includes engine, rotor and feedback control loop. As a fault detection method, we adopt the Kalman filter based method. To keep continuity of estimates between the changes of trim conditions, we reconfigure the initial values of state variables at trim changes. We detect the faults with two steps that when the first filter does not alarm the faults for some sensors, the second filter is runned for other sensor. Via some simulations we show that the proposed method works well under multiple trim conditions.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.43 no.8
• /
• pp.706-711
• /
• 2015

The fighter aircraft uses several different loading configurations for air-to-surface and air-to-air combat missions. To maintain wings-level flight with an asymmetric weapon configuration, a pilot controls a roll trim system. However, it is difficult to apply an accurate roll trim input for wings-level flight in the actual flight under disturbance. The inaccurate roll trim input degrades the performance of the roll autopilot system. In this paper, to solve this problem, an integrator was additionally designed in the command part of the roll autopilot system. The initial transient response was improved by scheduling the limiter to restrict the roll attitude error. As a result of the evaluation of the simulation for the designed flight control law, the roll attitude following performance was found to be improved in the autopilot system operation under the inaccurate roll trim condition.

• Journal of Fisheries and Marine Sciences Education
• /
• v.9 no.2
• /
• pp.179-187
• /
• 1997

Doppler log and current meter are based on the measurment of the doppler effect. Ship's speed over the ground measured by means of doppler log effect of underwater ultrasonic intends to get infulence by the difference of sound velocity, the ship's course, the sea bottom inclination, the trim and tranducer installation etc. This paper investigated on the error of speed over the ground by change of the trim comparing the real speed obtained by the mile post with the speed of single beam type doppler log on the trainning ship Kyeongyangho. The results are as follows ; 1. Indicating speed of doppler log is very much greatly influenced on variation of trim, but the real speed is less affected variation by trim. 2. The range of variation and error of speed over ground are smallest when ship's trim is 2.15m trim by the stern.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.1
• /
• pp.31-39
• /
• 2013

A Quad Tilt Wing UAV is a new concept hybrid UAV having the advantages of both fixed-wing and rotary-wing aircraft. This paper presents longitudinal flight dynamic characteristics of a Quad Tilt Wing UAV. The designed Quad Tilt Wing UAV is a configuration of a tandem wing type aircraft with an actuating motor and propeller mounted at each wing. Momentum theory is used to calculate the thrust, and nonlinear modeling is performed considering lift and drag generated by slip stream effect of propellers. Also, Force and moment variation at each tilting angle is considered. Static trim on longitudinal axis is analyzed via numerical simulation. Componentwise force contribution was analyzed at each trim mode. Dynamic characteristics were evaluated through eigenvalue analysis for a linear model at each flight mode. It is verified that longitudinal dynamic characteristics are changing from unstable to stable state by continuous transition of dominant poles.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.6
• /
• pp.487-497
• /
• 2011

Numerical analysis has been performed to investigate the rotor speed and pitch range variations when the airspeed is increased in autorotation. Transient Simulation Method(TSM) was used to obtain the steady states of autorotation. The rotor blade was analyzed by the two-dimensional compressible Navier-Stokes solver in order to adapt to the airspeed increase and the results were used in the transient simulation method. Meanwhile, the Pitt/Peters inflow theory was used to supply the induced velocity fields. For the prescribed torque equilibrium state, the combinations of velocity, shaft angle, and pitch angle were produced to investigate the rotor speeds and variable ranges. The rotor tip Mach number and rotor speed were correlated and the trim range of pitch angle was observed with respect to the shaft angle decrease.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.3
• /
• pp.215-223
• /
• 2009

In this paper, the helicopter aerodynamics is simulated in hovering and forward flight. Also, an overlapped grid technique is applied in this simulation to consider the blade motion and moving effects. The Caradonna & Tung's rotor blade was selected to analyze the unsteady aerodynamics in hovering and non-lift forward flight. Also, the AH-1G rotor blade was selected in forward flight. In forward flight case, the numerical trim was applied to determine the cyclic pitching angles using Newton-Raphson method, and the numerical results were in good agreement with experimental data, especially, the BVI effects were well simulated in advancing side in comparison other numerical results. The governing equation is a three dimensional unsteady Euler equation, and the Riemann invariants condition is used for inflow and outflow at the boundary.

• Composites Research
• /
• v.34 no.6
• /
• pp.350-356
• /
• 2021

When a ship with a planing line operates or turns in a straight line, the floating position and trim change according to the speed, and a large resistance is generated on the hull. In this paper, the resistance to a planing line was estimated through the computational fluid dynamics of a leisure boat with improved hull weight and durability by applying a carbon composite material to the hull. The resistance performance of the bow and stern of the 18ft class leisure boat was checked and the flow field of the entire vessel was estimated, and the stability of the planing line was confirmed by comparing the resistance of each trim through numerical analysis. In addition, it was confirmed that the designed planing line could withstand it sufficiently because the force applied to the hull was not large, and The stability of the boat was analyzed by calculating the wavelength of the wave and the length of the ship as the ratio of gravity to the inertial force and checking how much force the rolling occurred.