• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.243-246
• /
• 2001

In this paper, we have proposed a novel trench electrode Base Resistance Thyristor(BRT) and trench electrode BRT with a intrinsic region. A new power BRTs have shown superior electrical characteristics including snab-back effict and forward blocking voltage more than the conventional BRT. Especially, the trench electrode BRT with intrinsic region has obtained high blocking voltage of 1600V. The blocking voltage of conventional BRT is about 400V at the same size. Because the breakdown mechanism of BRT is avalanch breakdown by impact ionization, the trench electrode BRT with intrinsic region has suppressed impact ionization, effectively. If we use this principle, we can develope super high voltage power devices and applicate to another power devices including IGBT, EST and etc.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.2023-2025
• /
• 2002

We have fabricated a novel vertical trench-Hall device sensitive to the magnetic field parallel to the sensor chip surface. The vertical trench-Hall device is built on SOI wafer which is produced by silicon direct bonding technology using bulk micromachining, where buried $SiO_2$ layer and surround trench define active device volume. Sensitivity up to 350 V/AT is measured.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.46 no.2
• /
• pp.93-103
• /
• 2004

In trench excavation, essential factor of earth-retaining temporary work structure should be easy taking to pieces and movement, and dead weight must be less. This paper studies about the light weight material and application as earth-retaining structure to prevent the slope failure of sand soil ground caused by the variation of groundwater level in trench excavation. That is, light weight earth-retaining structural is proposed and a simulation with FEM on application of proposed structural in sandy soil is presented. The results are summarized as follows; (1) The study proposed FRP H-shaped pannel for the light weight member, and also presented estimation method about stability. (2) Mechanical property (bending moment, shear force, axial force, displacement) were changed according to groundwater level, but these values had been within enough safety rate and allowable stress. Therefore, proposed light weight pannel with FRP is available for bracing structure in trench excavation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.12S
• /
• pp.1255-1260
• /
• 2003

In order to reduce driving power consumption, we propose and fabricate a new structure of asymmetric SOI 1${\times}$2 thermo-optic switch that has a back side silicon trenched structure. Compared to conventional SOI thermo optic switches without heat sink structure, it shows an improvement of switching power reduction from about 4 watt to 1.8 watt without sacrificing cross talk of about 20 ㏈ at the light wavelength of 1.55 $\mu\textrm{m}$. Here we also described the main design consideration and fabrication procedure for the proposed device.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.2
• /
• pp.230-234
• /
• 1996

A new trenched Hybrid Schottky INjection Field Effect Transistor (HSINFET) is proposed and verified by 2-D semiconductor device simulation. The feature of the proposed structure is that the hybrid Schottky injector is implemented at the trench sidewall and p-n junction injector at the upper sidewall and bottom of a trench. Two-dimensional simulation has been performed to compare the new HSINFET with the SINFET, conventional HSINFET and lateral insulated gate bipolar transistor(LIGBT). The numerical results shows that the current handling capability of the proposed HSINFET is significantly increased without sacrificing turn-off characteristics. The proposed HSINFET exhibits higher latch-up current density and much faster switching speed than the lateral IGBT. The forward voltage drop of the proposed HSINFET is 0.4 V lower than that of the conventional HSINFET and the turn-off time of the trenched HSINFET is much smaller than that of LIGBT.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.2
• /
• pp.249-255
• /
• 1996

A self-aligned latch-up suppressed IGBT has been proposed and the process method and the device characteristics of the IGBT have been verified by numerical simulation. As the source is laterally diffused through the sidewall of the trench in the middle of the body, the size of the source is small and the doping concentration of the source is lower than that of the p++ body and the emitter efficiency of the parasitic npn transistor is low so that latch-up may be suppressed. No additional mask steps for p++ region, source, and source contact are required so that small sized body can be obtained Latch-u current density higher than 10000 A/cm$^{2}$ have been achieved by adjusting the process conditions.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.243-246
• /
• 2001

In this paper, we have proposed a novel trench electrode Base Resistance Thyristor(BRT) and trench electrode BRT with a intrinsic region. A new power BRTs have shown superior electrical characteristics including snab-back effect and forward blocking voltage more than the conventional BRT. Especially, the trench electrode BRT with intrinsic region has obtained high blocking voltage of 1600V. The blocking voltage of conventional BRT is about 400V at the same size. Because the breakdown mechanism of BRT is avalanch breakdown by impact ionization, the trench electrode BRT with intrinsic region has suppressed impact ionization, effectively. If we use this principle, we can develope super high voltage power devices and applicate to another power devices including IGBT, EST and etc.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.437-437
• /
• 2010

DC Hollow cathode 방전은 약 100여 년 전, Paschen에 의해 실험된 이후로 광원, 스퍼터링 공정, 이온빔 소스 등 다양한 분야에 이용되어 왔다. 최근 태양전지용 마이크로 결정질 실리콘 증착 시, RF CCP의 전극에 복수의 홀 혹은 트렌치 구조를 두어 Hollow cathode 방전 효과를 이용하여 향상된 공정 속도로 공정을 진행한다. 그러나 RF-MHCD (Multi hole cathode discharge) 공정을 위한 최적 규격의 홀 기에 관한 연구는 그 중요성과 응용성에도 불구하고 깊게 이루어지지 못한 바 있다. 그러므로 저자는 Capacitively Coupled Plasma (전극 간격 : 4cm, 전극 직경 : 14cm) 장비에서 평면 전극과 10mm 깊이와 각각 3.5mm, 5mm, 7mm, 10mm 직경의 홀이 있는 4개의 전극을 이용하여 Argon RF-MHCD 방전을 관찰하여 조건 별 최적의 홀 전극 디자인을 도출하였다. 실험 조건은 64.5mTorr ~ 645mTorr압력 범위/ 1A~9A이며, 플라즈마는 전극 사이 중앙에 설치한 RF-compensated Langmuir Probe와, 전극과 전기적으로 접촉하는 1000:1 Probe 와 Voltage-Current Probe를 이용하여 측정되었다. 실험 결과 압력 조건 별로, 최적의 전자 밀도를 유도하는 전극 상 홀의 직경이 달라짐을 확인하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.10
• /
• pp.885-888
• /
• 2008

We present simulation results on DC characteristics of AlGaN/GaN HEMTs having trench shaped source/drain Ohmic electrodes. In order to reduce the contact resistance in the source and drain region of the conventional AlGaN/GaN HEMTs and thereby to increase their DC output power, we applied narrow-shaped-trench electrode schemes whose size varies from $0.5{\mu}m$ to $1{\mu}m$ to the standard AlGaN/GaN HEMT structure. As a result, we found that the drain current was increased by 13 % at the same gate bias condition and the transconductance (gm) was improved by 11 % for the proposed AlGaN/GaN HEMT, compared with those of the conventional AlGaN/GaN HEMTs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.110-110
• /
• 2011

현재 전력 반도체는 신재생/대체 에너지 시스템, 자동차/전기자동차, 디스플레이/LED 드라이브 IC 등과 같이 산업용뿐만 아니라 가정용에서도 그 수요가 급증하고 있다. 이러한 전력 반도체는 각 시스템에서 전력 변환, 분배 및 관리를 하는 역할을 하게 되는데, 이러한 전력 시스템에 적용되기 위해서는 고속 스위칭, 낮은 전력 손실 및 발열, 소형화 등의 특성이 요구되어진다. 이러한 특성을 만족하기 위해 현재 전력반도체는 수평형 소자에서 수직 형태로의 구조적 변경을 꽤하고 있으며, 또한 수직형 구조에서도 더욱 소형화와 고밀도 전류, 낮은 전력 손실 특성을 구현하기 위해 여러 가지 형태의 어레이 기술을 개발하고 있다. 본 연구에서는 사각 형태의 어레이 (square array, mesh type)를 가지는 수직형 TDMOS (Trench double diffused metal oxide effect transistor)에서 트렌치 부분을 중심으로 액티브 영역과 그 외각 영역의 도핑 농도와 접합 깊이의 변화에 따른 전기적 특성 변화를 파악함으로써 TDMOS의 안정적인 구동 영역을 확보하기 위한 연구를 수행하였다. 본 연구는 silvaco 시뮬레이션 툴을 이용하여 실제 소자 제작 공정과 유사한 형태로의 공정을 가상적으로 진행하고, 액티브 영역과 그 외각 영역의 도핑 및 접합 깊이를 결정하는 이온 주입량과, 후속 열처리의 온도와 시간 등을 변화함으로써 그 전기적 특성을 상호 비교하였다.