• Environmental and Resource Economics Review
• /
• v.20 no.1
• /
• pp.1-31
• /
• 2011

By employing Environmental Input-Output Table 2005, which has 76 intermediate sector and 21 energy sources, this paper analyses the flow of energy demand and $CO_2$ after estimating an induced $CO_2$ emissions from 76 industrial sectors. Index of $CO_2$ intensity($CO_2/GDP$) and other index of $CO_2$ intensity($CO_2/calory$) showed that final demand sector uses more high calory energy source. Intermediate sector used less environmental friendly energy source and emit more $CO_2$ at same calory. Industries those has high induced $CO_2$ emissions are Thermal Power($32.587CO_2-g/Won$), Cement($10.370CO_2-g/Won$), Road Transportation($7.255CO_2-g/Won$), Cokes and Other Coal Products($5.791CO_2-g/Won$), Steam and Hot water supply, Sewage, Sanitary services($4.575CO_2-g/Won$). It is shown that industry such as Iron and Steel which has low $CO_2$ intensity, high backward linkage effect and high forward linkage effect makes high induced $CO_2$ emissions. Environmental load and $CO_2$ emissions in overall economy will decrease when not high $CO_2$ intensity industry but also low $CO_2$ intensity industry makes lower $CO_2$ intensity.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.7
• /
• pp.31-38
• /
• 2013

After debris flow caused damage during recent years, many scholars and engineers have thrown their effort into analyzing risk from debris flow in Korea. But it is hard to predict damage by debris flow taken place in wide area. Recently, SINMAP program is widely well used to estimate the amount of debris flow and its' range. In order to make frequent use of it, the most important thing is selection of accurate input parameters. In-situ experiments, which are avaliable in the mountain, is to be suggested to get dependable input parameters for SINMAP. Those are permeability, cohesion, density, friction angle and thickness in SINMAP. To get those, test pit, block sampling, in-situ density test, auger boring, permeability test on ground surface, borehole shear test and dynamic cone test and so forth were selected. In addition, the reliability of the results will be increased through comparing with those by laboratory tests. Hence, the experiments are hard to enter the sites without temporary road and, if possible, licensing and many times are needed, too. Small size experiments are indeed necessary to get accurate parameters.

• Journal of the Korean Society for Railway
• /
• v.14 no.5
• /
• pp.433-441
• /
• 2011

It is a fact that the straightening of track alignment is one of the undoubted ways to improve the train speed on conventional lines, while that requires huge investment resources. Therefore, the operation of a tilting train as well as the minimum improvement of track is suggested as an effective and economical alternative way for the speed-up of conventional lines. Since a driving mechanism of tilting train is different from those of existing trains, in order to make sure its operation safety and stability on conventional line, the performance of track and roadbed must be preferentially evaluated on the conventional line. Furthermore, it is necessary to estimate the tilting-train-induced roadbed response in detail since the roadbed settlement can lead to the track deformation and even derailment. In this research, the patterns of wheel load and lateral force were monitored and analyzed through the field tests, and the derailment coefficient and degree of wheel off-loading were calculated in order to evaluate the tilting train running safety depending on the running speeds (120km~180km) on the conventional line. Moreover, roadbed pressure, settlement and acceleration were also observed as tilting-train-induced roadbed responses in order to estimate the roadbed stability depending on the running speeds. Consequently, the measured derailment coefficient and degree of wheel off-loading were satisfied with their own required limits, and all of the roadbed responses were less than those of existing high-speed train (KTX) over an entire running speed range considered in this study. As a result of this study, the tilting train which will be operated in combination with existing trains is expected to give no adverse impact on the conventional line even with its improved running speed.

• Journal of Korean Society of Environmental Engineers
• /
• v.37 no.1
• /
• pp.7-13
• /
• 2015

In this study, the effective treatment reducing geosmin and dosage of PAC was suggested when taste & odor compounds flow in. The removal efficiency of geosmin was evaluated with types of chlorination. In case of low geosmin concentration below 25 ng/L, removal efficiency of geosmin was estimated at 46% by combined treatment of pre and intermediate-chlorination. But, in the exclusive intermediate-chlorination treatment, removal efficiency of geosmin was increased to 57%. In the medium geosmin concentration (25~79 ng/L), removal efficiency of geosmin was estimated at 59% by combined treatment. But, in the exclusive intermediate-chlorination treatment, removal efficiency of geosmin was increased to 87%. When high geosmin concentration above 80 ng/L flows in, removal efficiency of geosmin was estimated at 69% by combined treatment. However, in the exclusive intermediate-chlorination treatment, removal efficiency of geosmin was increased to 95%. Then, the exclusive intermediate-chlorination has an important effect on removal of geosmin. After correlation of geosmin concentration and dosage of PAC was analyzed, the coefficient of determination was estimated at 0.96. And, the proper PAC dosage chart was proposed. Also, at a initial occurrence of geosmin, when the combined treatment by intermediate-chlorination and PAC was applied, particle-bound geosmin should be removed continuously. Finally, it is proved that the combined treatment was effective to remove the geosmin by threshold levels as well as to reduce the dosage of PAC.

• The Journal of Engineering Research
• /
• v.4 no.1
• /
• pp.69-85
• /
• 2002

The chemical composition of bottle glass is consisted of Na2O-CaO-SiO2. However the cullet is mornally used in order to decrease the melting tsmperature. This induce the productivity of bottle and decreases the cost. The addition of plate glass decreases the Al2O3 content and in fluence the stone phenomenon and devitification in botle glass. Tus the Feldspar is added in order to increase the Al2O3 content when plate cullet was added in melting. The Tridymite crystal was observed over 7.5% Al2O3 contents, which shown as white crystal in appearance. It is Supposed that the Wollastonite Would be occurred in more over 7.5% Al2O3. This fad id well consised With the Litertctures.

• Journal of the Korean Geotechnical Society
• /
• v.34 no.12
• /
• pp.105-113
• /
• 2018

In this study, the engineering properties including bearing capacity of subgrades stabilized with a binder are analyzed by laboratory and field experiments. The main components of the binder are CaO and $SO_3$. After the binder was mixed with a low plasticity clay, the passing rates were relatively decreased as the sieve mesh size increased. Not only did the soil type change to silty sand, but engineering properties, such as the plasticity index and modified California bearing ratio (CBR), were improved for the subgrade. A comparison of the compaction curves of the stabilized subgrade and field soil compacted with the same energy demonstrated an increase of approximately 6% in the maximum dry unit weight, slight decrease in optimum moisture content, and considerable increase improvement in grain size. In the modified CBR test, the effect of unit weight and strength increase of the modified soil (with a specific amount of binder) was remarkably improved. As the proportion of granulated material increased after the addition of binder, the swelling was reduced by 3.3 times or more during initial compaction and 6.5 times by final compaction. The unconfined compressive strength of the specimens was maintained at the homogeneous value with a constant design strength. The stabilized subgrade was validated by applying it in the field under the same conditions; this test demonstrated that the bearing capacity coefficients at all six sites after one day of compaction exceeded the target value and exhibited good variability.

• Journal of Korean Elementary Science Education
• /
• v.40 no.4
• /
• pp.520-544
• /
• 2021

This study aims to develop a scientific creativity test for exploring the relationship between elementary students' creative process and product. For this, the researcher reviewed the literatures of scientific creativity and developed the items based on the constructs of creative process and product. After a review conducted by nine science education specialists, a pilot test, and additional revision and supplementation of observation test, the test, consisting of two sets-"animals" and "plants"-was finally conducted on 105 fifth-grade students. The test results were analyzed by using statistical analysis software. WinSteps, SPSS, and AMOS. The main findings from this study are as follows. First, when it comes to scientific creativity, creative process consists of science knowledge, inquiry skills, and creative thinking skills (divergent, convergent, and associative thinking skills). Creative product in science is a new and scientifically useful idea realized in a certain form. Second, observation, which was selected as a representative inquiry skill in this research, should not be related to creative thinking skills. Third, among the rest of the items, usefulness had the lowest averages, as it was, perhaps, difficult to satisfy the teachers' criteria for the scientific validity and usefulness. Fourth, the Spearman correlation coefficients between the items of "animals" and "plants" to find out the parallel-form reliability were significant, except for the item of originality. Fifth, the test was satisfactory with regard to the three aspects of construct validity-convergent, discriminant, and nomological. This study concludes by discussing the usefulness of this test, which has the possibility of exploring the relationship between creative process and product and of playing a role as an authentic evaluation tool in school.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.5
• /
• pp.517-529
• /
• 2021

This study analyzes changes in the efficiency of the Department of Early Childhood Education in Korea to examine the effectiveness of the National Evaluation for Teacher Education Institution. We provide policy implications from exploring factors influencing efficiency and comparing characteristics of efficient and inefficient departments. With 149 Department of Early Childhood Education in Korea, DEA was conducted to estimate the relative efficiency, and the Tobit model was applied to explore factors affecting efficiency. The results confirm that the Department of Early Childhood in Korea is run efficiently, though there was no change in scale efficiency and relative efficiency after the two phases of the National Evaluation for Teacher Education Institution. The results show the number of books per student was significantly lower despite a significantly higher employment rate. Efficiency of college departments, department greater than 60 (per cohort), and department in metropolitan city (except Seoul area) is confirmed greater. These results provide policy implications on developing evaluation measure and processes to improve education quality and efficiency.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.5
• /
• pp.329-334
• /
• 2023

This study attempted to examine the effect of corporate ESG activities perceived by college students on corporate loyalty and purchase intention. The results of the study are as follows. Looking at the average ESG activities recognized by college students, society 4.28 points, governance 4.25 points, and environment 4.12 points out of 5, and the average customer loyalty was 3.86 points when 3 points out of 5 points were median, and purchase intention was 3.84 points. Looking at the correlation between the factors of corporate ESG activities, customer loyalty, and purchase intention perceived by college students, it was confirmed that it had a static correlation coefficient. As a result of analyzing the effect of ESG activities perceived by college students on customer loyalty, the variable that significantly affects customer loyalty in [Model 1] is the major (β=.167p=).01) It was. Among the additional variables added to [Model 2], the variable that significantly affects customer loyalty is the environment (t=3.017, p<.).01), society ((t=4.365, p<.001), governance structure (t=-3.139, p<.01) was found to have a significant effect on customer loyalty. As a result of analyzing the effect of ESG activities perceived by college students on purchase intention, there was no significant effect on purchase intention in [Model 1]. Among the additional variables put into [Model 2], society (t=4.850, p<.001), governance structure (t=-3.452, p<.01) was found to have a significant effect on purchase intention.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.19 no.2
• /
• pp.43-53
• /
• 2017

This study aims to analyze the effect of typhoons on pear production. Pears are typical fruits that are vulnerable to typhoon damages, so typhoons are negatively associated with pear productivity. However, relatively less pear damages by typhoons in the main pear production area, comparing to the average in Korea, have been reported. The main production area seems to adopt better agricultural techniques or practices to cope with natural disasters such as typhoons. Thus, this study tests the hypothesis that there are differences of production losses due to typhoons between the main pear production area and the rest using the stochastic frontier analysis. The main production area is defined by Location Quotient Index (LQI), and we found that LQI had a significant effect to decrease the productivity losses in the main production areas, which shows that those production areas alleviated the pear production loss due to typhoons.