• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.3
• /
• pp.173-180
• /
• 2017

The main objective of a torque controller below rated wind speed is to extract maximum power from the potential wind energy. To do this, the torque control method, which adjusts the torque magnitude and makes it proportional to the square of the generator speed, has been applied. However, this method makes the response slower as the wind turbines are getting larger in size with multi-MW capacities. In this paper, a torque control method that uses the nonlinear parameter of rotor speed for aerodynamic torque as a control gain is discussed to improve the response by adjusting an additional torque magnitude. The nonlinear parameter of the rotor speed could be calculated both online and offline. It is shown that the offline case is more practical and effective in producing power through the numerical simulation of a 2MW wind turbine by considering the real turbulence wind speed.

• 유체기계공업학회:학술대회논문집
• /
• 2004.12a
• /
• pp.705-710
• /
• 2004

In the present study, a transient incompressible viscous turbulent flow is simulated for the automotive torque converter with moving mesh technique. For the analysis, entire torque converter flow passages are modeled. Computed torque ratio, capacity factor and efficiency show a good agreement with the experiment data. The flow instabilities characterized by back-flow and wake etc. appeared in some cascade passages are shown to be Propagating along tangential direction. These flow patterns are mainly influenced by the pump and turbine blade passing and can't be predicted through conventional steady simulation with a mixing plane approach. The understanding of the unsteady flow characteristics in a torque converter achieved in the present study may lead to the optimal design of a torque converter.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.5 s.38
• /
• pp.36-41
• /
• 2006

In the present study, a transient incompressible viscous turbulent flow is simulated for the automotive torque converter with moving mesh technique. For the analysis, entire torque converter flow passages are modeled. Computed torque ratio, capacity factor and efficiency show a good agreement with the experiment data. The flow instabilities characterized by back-flow and wake etc. appeared in some cascade passages are shown to be propagating along tangential direction. These flow patterns are mainly influenced by the pump and turbine blade passing and can't be predicted through conventional steady simulation with a mixing plane approach. The understanding of the unsteady flow characteristics in a torque converter achieved in the present study may lead to the optimal design of a torque converter.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.2
• /
• pp.355-362
• /
• 2021

Since coaxial magnetic gears use non-contact power transmission, friction, wear, noise, and heat generated in the power transmission process of existing mechanical gears can be minimized. Currently, research for application to various industries is being actively conducted, but among the characteristics of coaxial magnetic gears, the problem of rapidly decreasing torque density at a high gear ratio was discussed. This paper proposes a direction for multiple gear combination using low gear ratio coaxial magnetic gears with high torque density. In order to confirm the effectiveness of the method, the torque density was compared with a single high gear ratio model, and the combination and design direction of multiple coaxial magnetic gears were shown.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.717-718
• /
• 2015

전동기를 설계 시 자기등가회로법은 전동기의 세부 형상에 크게 구애를 받지 않기 때문에, 공간고조파법과 수치해석기법에 비해 유용하다. 이 논문에서는 Spoke type PMSM(Permanent Magnet Synchronous Motor)의 회전자 자기등가회로를 설계하였다. 회전자 자기등가회로를 통해, 마그네틱 토크 성분을 구성하는 공극자속밀도 수식을 이끌어 낼 수 있다. 이를 통해, Spoke type PMSM은 마그네틱 토크가 주 토크이기 때문에, 공극 자속밀도 및 형상치수비를 이용하여 전동기의 크기를 계산하였다.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.127-130
• /
• 2001

실의 잔류토크는 싱글저지 편성물에서 스파이럴러티를 일으키는 중요한 요소 중의 하나이다 실의 잔류토크를 감소시키거나 제거하기 위해서는 물리적으로 안정된 토크밸런스를 유지하도록 하는 방법과 퍼머넌트 세팅(permanent setting)방법 등을 택하고 있다. (중략)

• Journal of Dental Rehabilitation and Applied Science
• /
• v.24 no.2
• /
• pp.157-168
• /
• 2008

Tightening of the screws in implant restorations should be accurate and precise. If applied torque is too low, screw loosening would be occurred. With too high torque, the screw fracture might take place. Various torque generating devices are developed and employed to apply a proper torque. The purpose of this investigation was to determine and compare the accuracy of the torque controllers. In this study, 4 types of torque controllers were used; electronic torque controller, torque limiting device, torque indicating device and contra angle torque driver. Digital torque gauge was employed to measure the de-torque value. Thirty cycles of tightening and loosening were done with each torque controller. All implant torque controllers have shown slight errors and deviations. The torque liming device exhibited the most accurate data. No significant difference was found among the mean de-torque values of the electronic torque controller, torque indicating device and contra angle torque driver. In the limitation of this study, it would be recommended that the implant torque controllers should be checked whether uniformed and precise torque can be generated and a measuring error should be corrected.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.1
• /
• pp.35-41
• /
• 2013

Torque characteristics of a turbopump turbine was analyzed using the turbine performance test result. Specific torque of the subject turbine could be expressed as a linear function of corrected rotor speed at a fixed pressure ratio and it has been confirmed by the test result. It also found that corrected rotor speed-specific torque characteristics does not change anymore if the turbine pressure ratio is set bigger than a certain value. Using the turbine torque characteristics and pyro-starter performance test results, rotational speed development behavior of the turbopump was predicted. Prediction revealed that the lap time reaching 50% of turbopump design speed is less than 0.7 second. Effect of the thermal loss between pyro-starter and turbopump was negligible.

• Proceedings of the KIPE Conference
• /
• 2016.07a
• /
• pp.115-116
• /
• 2016

산업용 인버터에서 전차원 적응 자속 추정기를 적용하여 유도전동기 센서리스 제어를 하는 경우, 토크 제어 시 저속/저토크 영역에서 기동에 문제점을 보인다. 따라서 이를 해결하기 위해 본 논문에서는 동기 좌표계 상의 d축 전류의 크기를 토크에 따라 변동 시키는 방법을 제안한다. 주어진 토크 지령에 따라 발생되는 토크를 유지하기 위해, d축 전류 변동에 따라 q축 전류의 크기를 변화 시킨다. 운전 조건에 따른 d축 전류 크기의 변동 범위를 식을 통해 도출하였고, 복잡한 연산을 저 성능제어기에 적용할 수 있도록, d축 전류 크기를 간략히 설정하는 방법을 제안한다. 실제 인버터에 제안하는 방법을 적용하여 기존에 비해 훨씬 더 작은 토크만으로 기동 및 재 기동하는 것을 확인하였다.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.836-837
• /
• 2008

현재 화석에너지 고갈에 따른 다양한 신재생에너지의 활용에 대한 연구가 활발히 진행되고 있다. 본 논문은 영구자석을 사용한 수력용 영구자석 다극형 동기발전기의 기동토크 저감을 위한 최적설계 방안에 대해 연구를 수행하였다. 먼저 FEA 해석기법을 이용한 수력용 영구자석 다극형 동기발전기의 설계 및 발전기 기동토크에 가장 큰 영향을 주는 코깅토크 저감 방안에 대해 연구하였다. 코깅토크 저감을 위해 고정자 skew비에 따른 코깅토크의 변화를 FEA해석기법을 통해 알아보았으며, 실제 고정자에 skew를 적용하였을 때, 코깅토크의 최소화에 가장 적합함을 알 수 있었다. 또한 실제 설계된 영구자석 다극형 동발전기의 출력 및 코깅토크 측정 결과와 FEA해석결과를 비교 및 분석하여 FEA해석방법의 타당성을 입증하였다.