• Journal of the Korean Geosynthetics Society
• /
• v.18 no.4
• /
• pp.87-95
• /
• 2019

Earth-work calculation is the important data for estimating the optimal construction cost at the construction site. Earth-work calculations require the accurate terrain data and precise soil volume calculations. Drone surveying technology provides accurate topography in a short time and economic advantages. In this paper, a drone surveying technique was used to derive a high precision soil volume calculation system. Field demonstration were performed to verify the accuracy of the volume measurement system. The results of earth-work calculation using drone survey were compared with those of GPS surveying. In addition, the developed earth-work volume calculation algorithm is compared with the existing aerial survey software (Pix4D) to verify the accuracy.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.41 no.3
• /
• pp.317-325
• /
• 2021

Pine wilt disease first appeared in Busan in 1998; it is a serious disease that causes enormous damage to pine trees. The Korean government enacted a special law on the control of pine wilt disease in 2005, which controls and prohibits the movement of pine trees in affected areas. However, existing forecasting and control methods have physical and economic challenges in reducing pine wilt disease that occurs simultaneously and radically in mountainous terrain. In this study, the authors present the use of a deep learning object recognition and prediction method based on visual materials using an unmanned aerial vehicle (UAV) to effectively detect trees suspected of being infected with pine wilt disease. In order to observe pine wilt disease, an orthomosaic was produced using image data acquired through aerial shots. As a result, 198 damaged trees were identified, while 84 damaged trees were identified in field surveys that excluded areas with inaccessible steep slopes and cliffs. Analysis using image segmentation (SegNet) and image detection (YOLOv2) obtained a performance value of 0.57 and 0.77, respectively.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.43 no.2
• /
• pp.267-275
• /
• 2023

As aged infrastructures have been increased, the importance of accurate maintenance costs and proper budget allocation for infrastructure become prominent under limited resources. This study proposed a mapping algorithm between representative defects, repair methods, and the estimated maintenance costs for concrete bridges. In this regard, using BMS (Bridge Management System) data analysis, bridge repair methods were classified and matched with defects according to their locations, types, and sizes. In addition, the maintenance costs were estimated based on the amount of work-load and quantity per unit using CSPR (Cost Standard Production Rate). As a result, the level of accuracy was an average of 85.1 % compared with the actual bill of quantity for Seoul bridge maintenance. The accuracy of maintenance costs is expected to be enhanced by considering the various site conditions such as pier height, extra charge conditions, additional equipment, etc.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.27 no.5
• /
• pp.49-56
• /
• 2023

This study proposed a damage location estimation method for automated image-based port infrastructure inspection. Memory efficiency was improved by calculating the homography matrix using feature detection technology and outlier removal technology, without going through the 3D modeling process and storing only damage information. To develop an algorithm specialized for port infrastructure, the algorithm was optimized through ground-truth coordinate pairs created using images of port infrastructure. The location errors obtained by applying this to the sample and concrete wall were (X: 6.5cm, Y: 1.3cm) and (X: 12.7cm, Y: 6.4cm), respectively. In addition, by applying the algorithm to the concrete wall and displaying it in the form of an exterior damage map, the possibility of field application was demonstrated.

• Korean Journal of Construction Engineering and Management
• /
• v.23 no.2
• /
• pp.3-15
• /
• 2022

In this study, we develop a simulation model for Supply Chain Management (SCM) of modular construction based steel bridge. To this end, first, Factory Production/Site Construction system data for the steel bridge construction were collected, and supply chain, entities, resources, processes were defined based on the collected data. After that, a steel bridge supply chain simulation model was developed by creating data, flowchart, and animation modules using Arena software. Finally, verification and validation of the model were performed by using animation check, extreme condition check, average value test, Little' s law test, and actual case value test. As a result, the developed simulation model appropriately expressed the processes and characteristics of the steel bridge supply chain without any logical errors, and provided accurate performance evaluation values for the target system. In the future, we expect that the model will faithfully play a role as a performance evaluation platform in developing management techniques for optimally operating the steel bridge supply chain.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.6
• /
• pp.393-402
• /
• 2021

The first TBM introduced in Korea was the gripper TBM, which was applied to the Gudeok Waterway Tunnel in 1985. In the initial stage of the introduction of the gripper TBM, many applications were mainly focused on waterway tunnels (Tunnel Mechanized Construction Design, 2008). Currently, the construction range of gripper TBM in Korea is widely applied to not only waterway tunnels, but also subways, railway tunnels, and TBM+NATM expansion. Overseas, gripper TBM is generally applied, and even when NATM tunnel is applied, it is applied as an exploration tunnel because of the excellent advance rate of gripper TBM and used as an evacuation tunnel after completion. Due to the fast excavation speed, the application of the gripper TBM in the rock section of weathered rock or higher can minimize the environmental and civil complaints caused by creating a large number of work areas when planning long tunnels or mountain tunnels. In this study, the work process of the general gripper TBM was analyzed by analyzing the construction cycle and the gripper TBM with a diameter of 2.6~5.0 m, which was applied the most in Korea. Downtime was investigated and analyzed.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2023.05a
• /
• pp.86-86
• /
• 2023

최근에 들어 환경보전과 지속가능한 하천관리의 중요성이 대두되고 있으며, 통합물관리에 있어 수리량과 수질을 연계한 통합 모니터링의 필요성이 커지고 있다. 수리량과 수질 분야에 대한 모니터링 기술은 지속적인 연구가 이루어져 왔으나, 각 분야의 개별적 연구로 인해 수리량과 수질을 통합하여 모니터링 하는 기술 개발은 미흡한 수준이다. 또한 수질 측정은 수질오염공정시험기준에 있는 채수 기준에 따라 채수하여 측정하고 있으며, 채수 지점은 하천의 수심별로 달리하여 정해진다. 수리 측정은 현장계측을 통한 2차원적 계측으로 진행하고 있어 수질 측정 시 채수지점과 수리 측정지점은 일치하지 않는다. 동일 지점에서의 수질과 수리량을 동시에 고려하고 있지 못한 모니터링은 본류와 지류의 혼합거동이 많은 국내 하천 특성을 반영하지 못한다. 또한 현재의 수질·수리 모니터링은 ADCP나 다항목수질측정기 같은 고가의 장비를 운영하며, 홍수기와 같은 고위험 계측 조건에서 인력을 통해 측정하고 있기에 고비용의 장비운영비와 인명 피해를 야기시키고 있다. 따라서 무인 원격 기술을 적용한 하천 모니터링 기술과 수질과 수리량의 데이터 연계를 통한 3차원 모니터링 기술의 확보는 하천관리에 있어 매우 필수적이다. 본 연구에서는 수중 무인 원격이동체인 ROV와 무인 원격이동체(USV)를 활용한 3차원 수질·수리 모니터링 기술 개발에 관한 연구를 수행하였다. 국내 하천 특성을 고려한 혼합거동을 분석하기 위해 ROV에 수중 GPS 장비와 수질센서를 부착시켜 수중 내 2차원으로 측정되는 수리량과 동일한 좌표를 가지는 수질자료를 계측하여 하천의 연직 분포와 수평적 분포를 통해 화학적 수리적 거동을 분석하여 하천의 3차원 혼합거동 양상을 판단할 수 있었다. 이와 같은 무인 원격이동체를 통한 3차원 수질·수리 모니터링 기술은 하천의 3차원 분석에서 수질·수리량 보간 자료로 활용 가능하며, 효율적인 모니터링을 통하여 하천 전반 및 통합물관리에 있어 크게 기여할 것이라 사료된다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.5
• /
• pp.639-650
• /
• 2022

In areas where large-scale sediment transport occurs, it is important to apply appropriate countermeasure method because the phenomenon tends to accelerate by time duration. Among the various countermeasure methods applied so far, beach nourishment needs to be reviewed as an erosion prevention measure because the erosion pattern is mitigated and environmentally friendly depending on the particle size. In the case of beach nourishment. a detailed review is required to determine the size, range, etc., of an appropriate particle diameter. In this study, we investigated the characteristics of the related topographic change using the change in the particle size of nourishment materials, the application of partial area, and the condition under the coexistence of waves and wind as variables because those factors are hard to be analyzed and interpreted within results and limitation of that the existing numerical models are not able to calculate and result out so that it is required that phenomenon or efforts are reviewed at the same time through physical model experiments, field monitoring and etc. So we attempt to reproduce the tendency of beach erosion and deposition and predict possible phenomena in the future using machine learning techniques for phenomena that it is not able to be interpreted by numerical models. we used the hydraulic experiment results for the training data, and the accuracy of the prediction results according to the change in the training method was simultaneously analyzed. As a result of the study it was found that topographic changes using machine learning tended to be similar to those of previous studies in short-term predictions, but we also found differences in the formation of scour and sandbars.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.7
• /
• pp.17-25
• /
• 2007

Various geotechnical problems due to insufficient bearing capacity or excessive settlement are likely to occur when constructing roads or large complexes on soft ground. Accurate predictions of the magnitude of settlement and the consolidation time provide numerous options of ground improvement methods and, thus, enable to save time and expense of the whole project. Asaoka's method is probably the most frequently used one for settlement prediction and the empirical formulae such as Hyperbolic method and Hoshino's method are also often used. To find an elaborate method of predicting the embankment settlement, two recurrent type neural network models, such as Jordan model and Elman-Jordan model, are adopted. The data sets of settlement measured at several domestic sites are analyzed to obtain the most suitable model structures. It was shown from the comparison between predicted and measured settlements that Jordan model provides better predictions than Elman-Jordan model does and that the predictions using CPT results are more accurate than those using SPT results. It is believed that RNN using cone penetration test results can be a highly efficient tool in predicting settlements if enough field data can be obtained.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.3
• /
• pp.10-18
• /
• 2024

Vehicle loading is one of the main causes of bridge deterioration. Although WiM (Weigh in Motion) can be used to measure vehicle loading on a bridge, it has disadvantage of high installation and maintenance cost due to its contactness. In this study, a non-contact method is proposed to estimate the vehicle loading history of bridges using deep learning and CCTV images. The proposed method recognizes the vehicle type using an object detection deep learning model and estimates the vehicle loading based on the load-based vehicle type classification table developed using the weights of empty vehicles of major domestic vehicle models. Faster R-CNN, an object detection deep learning model, was trained using vehicle images classified by the classification table. The performance of the model is verified using images of CCTVs on actual bridges. Finally, the vehicle loading history of an actual bridge was obtained for a specific time by continuously estimating the vehicle loadings on the bridge using the proposed method.