• Journal of Satellite, Information and Communications
• /
• v.1 no.2
• /
• pp.63-70
• /
• 2006

This paper presents the results of Ka band qualification model multiplexers for COMS Payload to be launched in 2008. These are the input and output multiplexers of the satellite transponder to use available frequency resources effectively and the diplexer of the satellite antenna to use the same reflector for both transmitting and receiving frequency bands, respectively. The input multiplexer with four frequency channels has four(4) independent channel filters which consist of an 8-pole elliptic band-pass filter for high frequency selectivity and a 2-pole equalizer for group delay equalization. For low insertion loss, mass and volume reduction, manifold type os employed for output multiplexer. E-plane T-junction is used for either splitting or combining a frequency band into two sub-bands. Asymmetric inductive irises are used to tune the receiving filter easily. The electrical performance and environmental test such as vibration test, mechanical shock test, thermal vacuum test and EMC test are performed and the results of all qualification model multiplexers are compliant to the requirement of each multiplexer. Followed by this qualification, the flight model equipment will be developed.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.12
• /
• pp.1129-1134
• /
• 2007

Payload fairing protects satellites and electrical equipments from the external environment. Payload fairing is jettisoned before satellite separation. Assembly frame for the separation of payload fairing were assembled with shear bolts. The role of shear bolts is to support structural load during flight and they are cut by explosion of pyro. The assembly frame which is connected by shear bolts is separated after the cutting of shear bolts. In this paper, structural tests and analysis were done for the design of the shear bolt. Compression, bending and shear load apply to the hardware including assembly frame. Test results showed that design of the shear bolt satisfied both structural strength for the support of flight load and required low strength for the cutting of shear bolts.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.8
• /
• pp.55-63
• /
• 2018

In this paper, we measured the propagation path loss by a ground to air flight communication test at UHF band and analyzed the results. The ground receiving terminal was located at 1,100m above sea level in Cheju Island and the airborne transmit terminal flew at an altitude of 3.5km from 150 to 220km from the ground terminal. In this case, the ground terminal and the airborne terminal are on the Line of Sight. Therefore loss in this communications environment can be predicted based on Free Space Loss. However, in this test, the sea level exists between two terminals, and due to the very small angle of incidence on the reflecting surface due to the long-range communication environment, it is not possible to accurately predict the loss of free space only. Therefore, considering that there are no surrounding obstacles and that a line of sight is secured between the end of two terminals, we applied a plane earth reflection model and a spherical earth reflection model to estimate the propagation path loss and compared with the actual test results. As a result of the comparison, the predicted propagation path loss by a spherical earth reflection model were quite similar to the actual test values.

• Bulletin of the Korean Space Science Society
• /
• 2003.10a
• /
• pp.52-52
• /
• 2003

1996년 미국 버클리 대학의 Space Science Laboratory와 공동으로 고온 성간 물질의 관측에 대한 Conceptual Study로부터 시작되어 1998년 과학위성 1호의 주 탑재체로 선정되면서 본격적인 개발에 들어간 원자외선 분광기(FIMS: Far-ultraviolet IMaging Spectrograph)는 Engineering Model 개발, Qualification Model 개발, Flight Model의 개발 및 보정, 그리고 최종적으로 과학기술위성 1호 본체와의 조립 시험 및 환경시험을 거쳐 2003년 9월 26일 러시아의 플레세츠크에서 COSMOS-3M 발사체에 의해 발사된다. FIMS를 포함한 과학위성 1호는 현재 발사를 위해 러시아 현지에 이송되어 최종 시험을 진행 중이며, 발사 후 약 20일 가량은 위성의 운용 시험을 하게 되며, 이후 FIMS의 운용에 영향을 줄 수 있는 Out-gassing이 충분히 이루어진 후 FIMS의 Test 및 초기 운용이 이루어 진다. FIMS의 Detector로 사용되는 MCP(Micro Channel Plate)의 정상적 동작이 확인되면, 1년여에 걸쳐 FIMS의 주 임무인 원자외선 영역(900∼1750')의 은하계 전천 탐사를 수행하게 된다. 전천 탐사가 마무리 되면, 전천탐사의 결과를 바탕으로 개별 천체의 영상 및 분광 자료를 획득하게 되며, 동시에 원자외선 영역의 오로라 및 지구 대기광 측정을 수행한다.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.820-824
• /
• 2010

The purpose of this study is to develop basic technology of hybrid rocket vehicle by constructed and launched. This small hybrid rocket using HDPE/LN2O and Aluminium steel for its body (weight : 12.5 kg, diameter : 114 mm, height : 1.8 m) was designed. The fuel grain and injector were designed for 50 kgf thrust and burning time 2.5 sec. This rocket was loaded the data acquisition device for obtaining data of pressure and velocity during its flying and equiped an automatic ejector system using spring/motor and timer to collect the rocket more safely after launching. It was launched successfully, but found some problem that the rocket's weight was heavier than expected and the thrust was not enough to reach the designed altitude and analyzed its flight path way.

• Aerospace Engineering and Technology
• /
• v.6 no.1
• /
• pp.157-164
• /
• 2007

For a GPS antenna to normally receive GPS satellite signals during full flight mission of a satellite launch vehicle, it should be installed on skin of the vehicle. The surface of a launch vehicle is drastically heated up due to aerodynamic heating effect during flight, so that the GPS antenna mounted on surface of the launch vehicle is directly exposed to extremely hot temperature environment. Hot temperature test specification of the GPS antenna, therefore, is severer than inner components. This paper describes that procedures and results of performance analysis of the GPS antenna for KSLV-I under hot temperature environment. The GPS antenna was not deformed physically and inner LNA(Low Noise Amplifier) operated normally without performance degradation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.4
• /
• pp.359-366
• /
• 2009

MATLAB Autocode generation is a feature that converts a block diagram model in Simulink to a c program. Utilizing this function makes MATLAB/Simulink an integrated developing environment, from controller design to implementation. It can reduce development cost and time significantly. However, this automated process requires high reliability on the software, especially the original Simulink block diagram model. And thus, the verification of the codes becomes important. In this study, a UAV flight program which is generated with Simulink is validated and modified according to DO-178B. As a result of applying the procedures, the final program not only satisfied the functional requirement but is also verified with structural point of view with Decision Coverage 93%, Condition Coverage 95% and MC/DC 90%.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.4
• /
• pp.393-398
• /
• 2008

This paper suggests a GPS/INS navigation computer architecture that can be applied to small satellites. In order to implement a GPS/INS navigation system on a small satellite, the extreme environment in space such as radiation, micro-gravity, vacuum, etc. must be considered. In addition, a real-time processing ability is required for the GPS/INS navigation system since the formation flying of multiple small satellites is the ultimate goal. The developed navigation electronics utilizes a PowerPC-type MPC860T that has space environment heritage, and a pair of Atmega128s that has been implemented in KAUSAT-2 and has completed the space environment verification tests. The navigation algorithm is designed to work in VxWorks environment, ported in MPC860T.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.544-547
• /
• 2011

This paper describes on hardware simulation of passive power control of propulsion system for electric propulsion aircraft of KARI. The propulsion system uses hybrid power system that is composed of solar cell, fuel cell and battery. The fuel cell is replaces by simulator due to its difficulty in handling while the other components are the same as that will be used on board. As the result, reliable power supply for propulsion is confirmed and each power source is well operated showing its characteristics.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.97-100
• /
• 2008

A hybrid sounding rocket carrying about 10kg payload reaching up to 15km altitude has been designed. The commercial seamless aluminium tube and liquid ${N_2}O$ without pressurization devices were chosen as rocket motor case and oxidizer supply system respectively. A hybrid rocket engine performing required propulsion impulse is designed with time dependent internal ballistic scheme. Engine performance, aerodynamic characteristics, and trajectory were predicted by a integral technique of internal ballistics and external ballistics. The design results were evaluated by comparison with previous experimental data, technical reports, and literatures.