• Korean Journal of Remote Sensing
• /
• v.36 no.5_1
• /
• pp.679-692
• /
• 2020

We coupled a CFD model to the WRF-Chem model (WRF-CFD model) and investigated the characteristics of flows and carbon monoxide (CO) distributions in a building-congested district. We validated the simulated results against the measured wind speeds, wind directions, and CO concentrations. The WRF-Chem model simulated the winds from southwesterly to southeasterly, overestimating the measured wind speeds. The statistical validation showed that the WRF-CFD model simulated the measured wind speeds more realistically than the WRF-Chem model. The WRF-Chem model significantly underestimated the measured CO concentrations, and the WRF-CFD model improved the CO concentration prediction. Based on the statistical validation results, the WRF-CFD model improved the performance in predicting the CO concentrations by taking complicatedly distributed buildings and mobiles sources of CO into account. At 04 KST on May 22, there was a downdraft around the AQMS, and airflow with a relatively low CO concentration was advected from the upper layer. Resultantly, the CO concentration was lower at the AQMS than the surrounding area. At 15 KST on May 22, there was an updraft around the AQMS. This resulted in a slightly higher CO concentration than the surroundings. The WRF-CFD model transported CO emitted from the mobile sources to the AQMS measurement altitude, well reproducing the measured CO concentration. At 18 KST on May 22, the WRF-CFD model simulated high CO concentrations because of high CO emission, broad updraft area, and an increase in turbulent diffusion cause by wind-shear increase near the ground.

• Journal of Hydrogen and New Energy
• /
• v.7 no.1
• /
• pp.81-92
• /
• 1996

The Ar/Ar-$H_2$ plasma method was applied to reduce oxides and refine metals of V, Ta and B. In addition, the high temperature chemical reaction in Ar plasma and of the refining reaction in the Ar-(20%)$H_2$ plasma were analyzed. The crude V of 96wt% purity was obtained at the ratio of $C/V_{2}O_{5}=4.50$ by the Ar plasma reduction grade and the maximum reduction was obtained at $C/V_{2}O_{5}=4.50$ due to the $O_{2}$ loss from the thermal decomposition of vanadium oxide. In the Ar-(20%)$H_2$ plasma refining, the metallic V of 99.2wt% was produced at the ratio of $C/V_{2}O_{5}=4.40$. It was considered that a main refining reaction resulted from the chemical reaction between the residual carbon and residual oxygen. The metallic Ta of 99.8wt% was obtained at the ratio of $C/Ta_{2}O_{5}=5.10$ in a Ar plasma reduction and the Oz loss from the thermal decomposition of tantalum pentoxide did not take place. The deoxidation reaction was more significant than the decarburization reaction in the Ar-(20%)$H_2$ plasma refining and the metallic Ta of 99.9wt% was produced within the range of $C/Ta_{2}O_{5}$ ratio of 4.50 to 5.10. The Vickers hardness of Ta in the above mentioned range was about 220Hv due to the decrease in a residual oxygen by the deoxidation reaction. On the other hand, C is no suitable agent for the reduction of $B_{2}O_{3}$ by the Ar and Ar-$H_2$ plasma. But Fe-B-Si alloy was produced with the reduction of $B_{2}O_{3}$ in the melt when Fe, C, $B_{2}O_{3}$, and ferroboron mixtures were melted by the high frequency induction melting.

• Journal of Life Science
• /
• v.30 no.4
• /
• pp.370-378
• /
• 2020

This study aimed to investigate the hepatoprotective effect of Dendropanax morbifera (D. morbifera) leaf hot-water extract on carbon tetrachloride (CCl₄)-treated HepG2 cells. Treatment with D. morbifera leaf hot-water extract increased the cell viability of CCl₄-treated HepG2 cells without inducing cytotoxicity. The levels of alanine transaminase (ALT) and aspartate transaminase (AST) released by CCl₄-treated cells were 27.6 U/L and 52.4 U/L, respectively, and were significantly higher than those in untreated control cells (10.0 U/L and 15.2 U/L, respectively). Moreover, the level of γ-glutamyl transpeptidase (GGT) was 5.4 times higher, while that of glutathione was 44.0% lower in CCl₄-treated cells than in control cells. However, treatment with D. morbifera leaf hot-water extract resulted in a dose-dependent decrease in the levels of ALT, AST, and GGT, and an increase in the level of glutathione. Moreover, the malondialdehyde (MDA) content in CCl₄-treated HepG2 cells was effectively reduced after treatment with D. morbifera leaf hot-water extract. Additionally, overproduction of intracellular lipids induced by CCl₄ treatment was effectively inhibited by D. morbifera leaf hot-water extract treatment. Furthermore, DCFDA staining showed that overproduction of reactive oxygen species (ROS) induced by CCl₄ treatment was effectively reduced by treatment with D. morbifera leaf hot-water extract. Our results indicate that owing to its beneficial effects, D. morbifera leaf extract has considerable potential as a functional food material for liver protection.

• Korean Journal of Heritage: History & Science
• /
• v.53 no.4
• /
• pp.100-117
• /
• 2020

National Treasure no. 101, the stupa of State Preceptor Jigwang from the Beopcheonsa Temple Site in Wonju has been transferred from place to place and reassembled several times since it was built. In particular, overall dismantling and repair was carried out in 1957 to restore parts damaged by bombing during the Korean War. Documented information on the repair process and materials used at that time does not exist. However, various types of metal materials used for this stupa have been identified during conservation work. Besides clamps anchor bolts, 9mm-thick circular rebars were mainly used for joining the parts of this stupa, while circular rebars and wires of various thicknesses were used for joining the parts with mortar restoration materials. Although deformed bars are typically used for stone pagodas classified as architectural structures, smooth circular rebars were used in this case. In terms of restoration using mortar, material shapes were transformed, bound alternately, and twisted irregularly to improve bonding strength and coherence in order to insert restoration materials and to bolster structural weaknesses. In addition, metallographic analysis showed the material to be hypo-eutectoid steel with low carbon content. Many non-metallic inclusions in the shape of drops of different sizes were included, which do not affect the whole elemental composition due to the very small quantities involved. Qualitative and EPMA analysis of Mn and S, which were not identified by SEM-EDS area analysis, established an even distribution of MnS in crystal grains of the microstructure, regardless of the shape of the samples. It is presumed that secondary homogenization and softening might have been conducted after manufacturing to facilitate the working process. Furthermore, in consideration of properties indicating that the thinner the steel is, the less carbon content contained and the greater the elasticity and elongation, it is judged that restoration work was ordered.

• Journal of Life Science
• /
• v.28 no.5
• /
• pp.577-586
• /
• 2018

We recently reported the potential probiotic properties of Lactobacillus brevis SBB07 isolated from blueberries. The present study investigates the effect of culture conditions such as temperature, initial pH, culture time, and medium constituent for industrial application. The ingredients of the medium to improve cell growth were selected by Plackett-Burman design (PBD) and central composite design (CCD) within a desirable range. The PBD was applied with 19 factors: seven carbon sources, six nitrogen sources, and six microelements. Protease peptone, corn steep powder (CSP), and yeast extract were found to be significant factors for the growth of SBB07. The CCD was then applied with three variables found from the PBD at five levels, and the optimum values were decided for the three variables: protease peptone, CSP, and yeast extract. In the case of the growth of SBB07, the proposed optimal media contained 2.0% protease peptone, 2.5% CSP, and 2.0% yeast extract, and the maximum dried-cell weight was predicted to be 2.93963 g/l. By the model verification, it was confirmed that the predicted and actual results are similar. Finally, the study investigated the effects of incubation temperature and initial pH at the optimized medium. It was confirmed that the dried-cell weight increased from $2.2933{\pm}0.0601g/l$ to $3.85{\pm}0.0265g/l$ when compared to the basal medium at $37^{\circ}C$ and initial pH 8.0. Establishing the optimal culture condition for SBB07 provides good potential for applications in probiotics and can serve as the foundation for the industrialization of materials.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.5
• /
• pp.563-572
• /
• 2006

In order to propose optimum in-situ treatment for reducing phosphorous release from sediment of stationary lakes, a series of column tests were performed. The sediment used in experiment was very fine clay with a mean grain site $7.7{\phi}$ and high $C_{org}$ contents(2.4%). Phosphorous releases were evaluated in two ways : in lake water(with microbial effect) and in distilled water(without microbial effect). As in-situ capping material, sand and loess were used while Fe-Gypsum and $SiO_2$-Gypsum were used for in-situ chemical treatment. In case of lake water considering the effect of microorganism, phosphorous concentration rapidly decreased in the early stage of experiment but it was gradually increased after 10 days. Flux of phosphorous release for control was $3.0mg/m^2{\cdot}d$. Whereas, those for sand layer capping(5 cm) and loess layer capping(5 cm) were $2.5mg/m^2{\cdot}d\;and\;1.8mg/m^2{\cdot}d$, respectively because the latter two were not consolidated sufficiently. For Fe-gypsum and $SiO_2$-gypsum the fluxes were $1.4mg/m^2{\cdot}d$ which meant that reduction efficiency of phosphorous release was more than 40% higher than that of control. The case capping with complex layer was $1.0mg/m^2{\cdot}d$, which showed high reduction efficiency over 60%. The addition of gypsum($CaSO_4{\cdot}2H_2O$) into the sediment reduced release of Phosphorus from the sediments. Gypsum acted as a slow-releasing source of sulphate in sediment, which enhanced the activity of SRB(sulfate reducing bacteria) and improved the overall mineralization rate of organic matter.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.11
• /
• pp.1180-1185
• /
• 2006

Lab-scale batch experiments using several 25-L transparent acrylic reactors were conducted to develop optimum capping materials that can reduce phosphorus released from polluted sediments. The sediment used in the experiment was very fine clay(8.8 $\Phi$ in mean grain size), and organic carbon($C_{org}$) content was as high as 2%. Four kinds of batches with different capping materials Brucite($Mg(OH)_2$), Sea sand($SiO_2$), Granular-gypsum($CaSO_4{\cdot}2H_2O$), Double layer(brucite+sand), and one control batch were operated for 30 days. Phosphorus fluxes released from bottom sediments in the control batch were estimated to be 14.6 $mg{\cdot}m^{-2}{\cdot}d^{-1}$, while 9.5 $mg{\cdot}m^{-2}{\cdot}d^{-1}$, 5.2 $mg{\cdot}m^{-2}{\cdot}d^{-1}$, 4.2 $mg{\cdot}m^{-2}{\cdot}d^{-1}$, and 3.1 $mg{\cdot}m^{-2}{\cdot}d^{-1}$ in the batch capped with Sea sand, Granular-gypsum, Double layer, and Brucite, respectively. The results obtained from lab-scale batch experiments show that there were 70% reduction of phosphorus for some materials such as Brucite, Double layer(brucite+sand), and whereas sea sand only about 35%. The pH range of surface sediment to which Brucite was applied showed about $8.0{\sim}9.5$ in the weak alkaline state. This effect can prevent liberation of $H_2O$. The addition of gypsum into the sediment can reduce the progress of methanogenesis because of fast early diagenesis and sufficient supply of $SO_4^{2-}$ to the sediments, stimulate the SRB highly. Therefore, the application of Brucite and Gypsum can reduce phosphorus release from the sediment as a result of formation of $Mg_5(OH)(PO_4)_3$, pyrite($FeS_x$), and apatite-mineral.

• Food Science and Industry
• /
• v.55 no.2
• /
• pp.188-202
• /
• 2022

In the insect industry, as the scope of application of insects is expanded from pet insects and natural enemies to feed, edible and medicinal insects, the demand for quality control of insect raw materials is increasing, and interest in securing the safety of insect products is increasing. In the process of expanding the industrial scale, controlling the temperature and humidity and air quality in the insect breeding room and preventing the spread of pathogens and other pollutants are important success factors. It requires a controlled environment under the operating system. European commercial insect breeding facilities have attracted considerable investor interest, and insect companies are building large-scale production facilities, which became possible after the EU approved the use of insect protein as feedstock for fish farming in July 2017. Other fields, such as food and medicine, have also accelerated the application of cutting-edge technology. In the future, the global insect industry will purchase eggs or small larvae from suppliers and a system that focuses on the larval fattening, i.e., production raw material, until the insects mature, and a system that handles the entire production process from egg laying, harvesting, and initial pre-treatment of larvae., increasingly subdivided into large-scale production systems that cover all stages of insect larvae production and further processing steps such as milling, fat removal and protein or fat fractionation. In Korea, research and development of insect smart factory farms using artificial intelligence and ICT is accelerating, so insects can be used as carbon-free materials in secondary industries such as natural plastics or natural molding materials as well as existing feed and food. A Korean-style customized breeding system for shortening the breeding period or enhancing functionality is expected to be developed soon.

• Applied Microscopy
• /
• v.39 no.4
• /
• pp.311-317
• /
• 2009

This study was performed using animals to confirm the effect of tourmaline-ionized water (TIW) the properties of which were changed by tourmaline energy and electric discharge. In the ICR mice fed high-fat diet, body weight increasing rate of the TIW-treated group (Exp) was generally decreased and moreover exhibited significance at 11th week (P<0.05) compared with the control (Con) group fed distilled water, although water intake of the Exp group was lower than that of the Con group. In the ICR mice with $CCl_4$-induced hepatotoxicity, AST and ALT activities of the Exp group were not significant but showed some decreasing trend, and histological damage of liver was less compared with thatof the Con group. On the study of ethanol-induced hangovers in Sprague-Dawley rat, blood alcohol concentration was significantly decreased (P<0.01), activity of GST, antioxidant enzyme related to the alcohol metabolism, was increased in liver tissue (P<0.05), and AST and ALT show a tendency to be decreasedin the Exp group. These results suggest that drinking TIWhas not only some obesity preventing effect but also an alcohol detoxification effect and liver protecting effect in vivo. It is supposed due to a structural change of water cluster and a property which maintains the changed structure through tourmaline energy and electric discharge. Therefore, TIW has a potentiality to be developed as functional water with several beneficial effects as well as for daily drinking, but further study on the mechanism related with efficacy will be necessary.

• Korean Chemical Engineering Research
• /
• v.50 no.4
• /
• pp.702-707
• /
• 2012

During the last few decades, toxic chemicals used in various industries have caused global pollution and the side products such as carbon dioxide and methane gas have contributed to global warming. Thus, it is desirable to develop new alternative solvents. It is well known that ionic liquids display a variety of environmentally friendly physical properties: nonvolatile, nonflammable, wide electrochemical windows, high inherent conductivities, wide thermal operating ranges, chemically inert, and limited miscibilities with organic solvents. Because of these characteristics, ionic liquids are promising candidates as solvents for synthetic chemistries, catalysis, and gas separations. In this study, we synthesized morpholiunium salts as N-ethyl-N-methylmorpholine Bromide, N-butyl-N-methylmorpholine Bromide, N-octyl-N-methylmorpholine Bromide, N-ethyl-N-methylmorpholine Tetrafluoroborate, N-butyl-N-methylmorpholine Tetrafluoroborate, N-octyl-N-methylmorpholine Tetrafluoroborate, N-ethyl-N-methylmorpholine Hexafluorophosphate, N-butyl-N-methylmorpholine Hexafluorophosphate, and N-octyl-N-methylmorpholine Hexafluorophosphate. The melting points, decomposition temperatures and electrochemical stabilities of the salts were measured by DSC, TGA, and CV, respectively. The salts with halide anion showed high melting points ($150{\sim}200^{\circ}C$), low decomposition temperatures ($200{\sim}230^{\circ}C$), narrow electrochemical stabilities (3.4~3.6 V). The synthesized salts with inorganic anions, on the other hand, presented low melting point ($50{\sim}110^{\circ}C$), high decomposition temperatures ($250{\sim}380^{\circ}C$), wide electrochemical stabilities (6.1~6.3 V). We also found that the properties depend on the length of the carbon chain.