• Geophysics and Geophysical Exploration
• /
• v.13 no.4
• /
• pp.307-314
• /
• 2010

Although conventional seismic data processing is based on the assumption that the media are isotropic, the subsurface is often anisotropy in shale formation or carbonate with cracks and fractures. This paper presents the anisotropic parameter and seismic modeling in transversely isotropic media with a vertical symmetry axis using seismic physical modeling. The experiment was successfully carried out with VTI media, laminated bakelite material, using contact transducer of p and s-wave transmission. The variation of velocities with angle of incidence was clearly shown in anisotropic material. Comparing these velocities with the calculated phase velocities, the (P) and (S)-wave velocity observed in anisotropic material was a very good agreement with the calculated values. Anisotropic parameter ${\varepsilon}$, ${\delta}$, ${\gamma}$ was estimated by using Lame's constant calculated from the observed velocity. For the purpose of testing (S)-wave polarization, a birefringence experiment was carried out. The higher velocity was associated with the polarization parallel to the fracture, and the lower velocity was associated with the polarization perpendicular to the fracture.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.10 no.4 s.50
• /
• pp.1-13
• /
• 2006

Soil and rock dynamic properties such as shear wave velocity $(V_s)$, compressional wave velocity $(V_p)$ and corresponding Poisson's ratio (v) are very important geotechnical parameters in predicting deformational behavior of structures as well as practicing seismic design and performance evaluation. In an effort to measure the parameter efficiently and accurately, various bore-hole seismic testing techniques have been, thus, developed and used during past several decades. In this study, cross-hole seismic testing technique which is known as the most reliable seismic method was adopted for obtaining geotechnical dynamic properties. To perform successfully the cross-hole test for rock as well as soil layers regardless of the ground water level, spring-loaded source which impact laterally a subsurface ground in vertical bore-hole was developed and applied at three study areas, which contain four sites composed of two existing port sites and two new LNG storage facility sites. The geotechnical dynamic properties such as $V_s,\;V_p$ and v with depth from the soil surface to the engineering and seismic bedrock were efficiently determined from the laterally impacted cross-hole seismic tests at study sites, and were provided as the fundamental parameters for the seismic performance evaluation of the existing ports and the seismic design of the LNG storage facilities.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2005.09a
• /
• pp.155-175
• /
• 2005

Soil and rock dynamic properties such as shear wave velocity (VS), compressional wave velocity (VP) and corresponding Poisson's ratio ( v ) are very important geotechnical parameters in predicting deformational behavior of structures as well as practicing seismic design and performance evaluation. In an effort to measure the parameter efficiently and accurately, various bore-hole seismic testing techniques have been, thus, developed and used during past several decades. In this study, cross-hole seismic testing technique which is known as the most reliable seismic method was adopted for obtaining geotechnical dynamic properties. To perform successfully the cross-hole test for rock as well as soil layers regardless of the ground water level, spring-loaded source which impact laterally a subsurface ground in vertical bore-hole was developed and applied at three study areas, which contain four sites composed of two existing port sites and two new LNG storage facility sites. The geotechnical dynamic properties such as VS, VP and v with depth were efficiently determined from the laterally impacted cross-hole seismic tests at study sites, and were provided as the fundamental parameters for the seismic performance evaluation of the existing ports and the seismic design of the LNG storage facilities.

• Tunnel and Underground Space
• /
• v.28 no.3
• /
• pp.232-246
• /
• 2018

In this study, the relationship between in situ seismic wave velocities and RMR (rock mass rating) was investigated in a test bed for the examination of the basis of rock classification (RMR) based on seismic wave velocity. The seismic wave velocity showed a monotonous increase with depth. It was also found that there was no systematic correlation between the seismic wave velocity (Vp) and other parameters (RQD, joint spacing, UCS, rock core Vp, and RMR) collected at the same depth of the same borehole. However, correlative relation was observed among RMR, RQD, and joint spacing. On the other hand, when all the data in the borehole (three holes) are examined without considering the depth, Vp still shows no correlation with RMR parameters (e.g., correlative coefficient for uniaxial compressive strength and joint spacing are 0.039 and 0.091, respectively), but Vp shows weak correlative relation with RMR and RQD (correlative coefficient for RQD and RMR are 0.193 and 0.211, respectively). Thus, it is found that it is difficult to deduce physical properties of rock mass directly from seismic wave velocities, but the seismic wave velocity can be used as a tool to approximate rock mass properties because of weaker correlation between Vp and RMR with RQD. In addition, the velocity value of for soft and moderate rocks suggested by widely used construction standards is slower than that of the observed velocity, implying that the standards need to be examined and revised.

• Geophysics and Geophysical Exploration
• /
• v.5 no.3
• /
• pp.141-144
• /
• 2002

Three-dimensional seismic data, recorded with an interval of one year, indicate a velocity changes in the medium at the near surface. During that period of a year, the ground reinforcement work has been conducted at the railroad base in the study area. The time-thickness to the first reflector of the two data were picked and compared. The result showed that the velocity of the medium decreased at large part of the study area; however, no velocity decrease at the railroad base.

• Geophysics and Geophysical Exploration
• /
• v.14 no.4
• /
• pp.324-334
• /
• 2011

Seismic wave velocity change has been monitored due to the accumulation of micro-cracks by uniaxial loads on the rock samples from Seokmo Island with stepwise increase in 5 stages. After the load was applied up to 95% of UCS, P- and S-wave velocities varied in ranges of 0.9 ~ 18.3% and 2.8 ~ 14.8% of fresh rock sample velocities, respectively. Unlike seismic velocity of the dry rock samples that showed overall decreases after the loading, velocity changes of saturated rock samples were much more complicated. These seemed to be due to the mixture of two contradictory mechanisms; i.e. accumulation of micro-crack causes an increase in porosity and a decrease in wave velocity, while saturation causes an increase in wave velocity. Most of tested rocks showed a trend of velocity increase with low axial load and then velocity decrease at later stages. Starting stage of velocity decrease differs from samples to samples. After the failure of rock occurred, noticeable increases of porosity and decreases of wave velocity have been observed. It showed overall trend that the more the quartz contents and the lower the silicate, the higher the Young's modulus.

• Journal of the Korean Geotechnical Society
• /
• v.28 no.8
• /
• pp.55-63
• /
• 2012

The evaluation of shear modulus (or shear wave velocity) profile of the site is very important in various fields of geotechnical engineering and various surface wave methods have applied to determine the shear wave velocity profiles and showed good performance. Surface wave methods evaluate the dispersion curve in the field and determine the shear wave velocity profile through the inversion process. In this paper, the automated inversion process using the genetic algorithm is developed for HWAW method which is one of surface wave methods recently developed. The proposed method uses the error function based on the wavelength domain dispersion curve and can determine the reliable shear wave velocity profile not only in shallow depth but also in deep depth. To estimate the validity of the proposed method, numerical simulations and field test were performed and the proposed method was applied to determine the shear wave velocity profiles. Through the numerical simulations and field applications, the promising potential of the proposed method was verified.

• The Journal of Engineering Geology
• /
• v.18 no.4
• /
• pp.371-379
• /
• 2008

In this study, seismic elastic wave and dynamic elastic modulus properties are investigated by down-hole seismic tests that were applied to the 11 gneiss area. The research results show that the realtionship between the two properties are $V_s=0.5589{\times}V_p$ in gneiss. The relationship between the two properties are separated into two groups. Group 1 is influenced mainly by the specific gravity of rock, but group 2 is influenced mainly by the joint aperture. As weathering progresses, group 1 clearly shows a decreasing tendency. In fresh and slightly weathered rock-mass, correlations between $V_p$ and dynamic elastic modulus is expressed in linear line but in moderately-highly weathered rock-mass, correlations between $V_p$ and dynamic elastic modulus is expressed curve as a quadratic function. Correlations between $V_s$ and dynamic elastic modulus are analyzed similar with a $V_p$ case.

• The Korean Journal of Petroleum Geology
• /
• v.1 no.1 s.1
• /
• pp.29-35
• /
• 1993

Seismic reflection data can be used to extract information about the velocity structure of the earth. This process is called a velocity inversion of the seismic data. However, it is difficult to recover a broad band reflection coefficient series because the frequency band of seismic trace is limited. The linear programming method has been examined to find the simplest velocity model that has frequency components consistent with the usable frequencies of the seismic trace and interval velocity data. The velocity structure of the earth is displayed in pseudovelocity section. After the linear program had been tested with a synthetic seismic trace, it was applied to the seismic reflection data of the Block Ⅱ in the Yellow Sea. By comparing the pseudovelocity section with sonic logs obtained from the well in the same area, it was possible to define the lithostratigraphy and the boundaries of Cretaceous volcanics and Cretaceous metavolcanics.

• Geophysics and Geophysical Exploration
• /
• v.2 no.3
• /
• pp.137-141
• /
• 1999

In order to estimate the anisotropy of the medium, we deployed a series of 120-sources in a borehole, and simultaneously recorded 3-component seismic data at 5 locations on the surface. We have tried to estimate the directional velocities by comparing the first arrivals at different receivers. For that purpose, the receiver statics must be corrected prior to pick the first arrivals. However, in an IVSP with a limited number of receiver points, it may not possible to estimate a reliable receiver statics, therefore, instead of using individual first arrival times, we tried to estimate the move-out velocity at each records. From this analysis, we have found that there exists a measurable amount of difference in directional velocities, and confirmed that the velocity anisotropy agrees with the results of the previous studies conducted in this area.