• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.10-13
• /
• 2010

세그먼트 자중 등에 의한 휨모멘트와 케이블 수직압축력에 의한 합성응력이 발생되고 바닥판 경간비가 변하는 사장교의 시공단계에서는 전단지연의 영향범위가 다를 수 있다. 이 연구에서는 1면 케이블 콘크리트 박스 사장교를 대상으로 시공단계시 보강형에 고려되어야 할 합성응력에 의한 유효플랜지폭을 분석하였다. 그 결과 바닥판 경간비가 0.38 이하의 범위에서 보강형의 전폭을 유효플랜지폭으로 적용할 수 있는 것으로 해석되었다. 따라서 시공단계시 변화되는 바닥판 경간비의 크기에 관계없이 전폭을 유효플랜지폭으로 반영하는 실무관행은 안전측 설계가 되지 못할 수 가 있다. 바닥판 경간비가 작아짐에 따라서는 전폭과 캔틸레버 구조계로 유효플랜지폭을 결정하는 것이 타당하다. 이 연구에서는 수직력에 대한 도로교설계기준의 유효플랜지폭 규정에 대한 평가도 수행하였다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2009.05c
• /
• pp.99-102
• /
• 2009

This paper is to present the performance data for pressure setting method using some tile bonds for application on the Ondol-Heating floor system. For this purpose, powder and liquid tile bonds(Organic.Inorganic mixed tile bonds) were compared with the conventional tile cement for pressure setting method in the sight of the adhesive stability of porcelain tile. It tested for tiles after 14, 28days under standard condition and severe conditions. The severe conditions were water immersion and heat ageing($70^{\circ}C$). Another experimental factors concerned tile bond properties such as mixing ratio(in case of using liquid admixture), open time, which are supposed to affect the tensile strength of tile, were studied and discussed through the experiments.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2005.05a
• /
• pp.173-178
• /
• 2005

The tile construction methods for existing have been used materials within limit which adhesion by wet method in masonry wall and concrete structure. These existing adhesive tech can caused many problems in construction of large and reform tile, after that it can be happened loose scale, peel off, falling off tile by heat and vibration or impact. In according to, this study is to test tile for bond stability, adhesive property by impact, vibration. low property by heat and then, we have the results as below; (1) The tile adhesive stability can be effected as adhesive area between bond agent and tile, adhesive area can more wide and press enough to ensure property. (2) Existing adhesive strength and standard relative tile construction is limited to adjust performance tile on the concrete and masonry wall. In summary, It is necessary to establish standard of performance and test method to ensure tile adhesive salability in dry wall.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.265-268
• /
• 2008

In this paper behavior of U-Channel Bridge (UCB) and the slab design considering construction sequence was studied. The segments of UCB are produced in the factory and transported to the site by trailers, and the segments are fabricated in the construction field. In this sequence the supporting conditions are changed. Four steps that were the segment precasting step, the segment carrying step, the segment placed on the erection beam step, and the completion step were chosen by supporting condition. In each step model using the frame and plate elements was proposed and structural analysis was performed. Four construction steps were to be considered in the process of slab analysis. The design method of slab was proposed considering construction sequence.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1046-1047
• /
• 2015

기존에 시행 중인 도로교통 소음을 저감시키기 위한 방안인 방음벽과 저소음 포장은 보편적으로 사용되어 오고 있으나, 몇 가지 단점을 가지고 있다. 방음벽은 높은 시공으로 인한 도시 경관 저하, 과도한 시공비 및 유지비, 조류가 방음벽에 부딪혀 유발되는 생태계 교란 현상 등 여러 문제점을 가지고 있다. 또한, 저소음 배수성 포장은 타이어와 도로 포장간의 마찰 소음을 원천적으로 저감시키는 효율적인 공법이나, 시공 후 일정기간이 지나면 공극이 막혀 성능이 저하되어 유지 보수가 적절하게 필요한 단점이 있다. 수음점의 거리별 소음예측을 통하여 일반적인 원소음과 능동형 소음 저감 기술(ANC) 적용 후의 효과를 알아보고, 소음원의 제어 및 영향거리에 따른 저감 목표를 예측하고자 한다.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.219-220
• /
• 2012

Steel method compared with conventional aluminum truss construction materials as the biggest difference, aluminum truss method by using an aluminum material construction of the existing steel truss compared with the welding operation is omitted, as the air operations will be reduced by about 40% do not need skilled workers in the existing portion of each tube and cost 11,233 to 13,173 won/㎡ cheap it was found.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.6
• /
• pp.105-111
• /
• 2009

Construction equipment is a very important factor for successful construction. Also, the cost for construction equipment is a major part of the cost of construction. Therefore, the estimation of the equipment cost is a critical task in construction planning. A formula for production rates shown in 'Standard Unit Labor' has been used to estimate construction equipment capability and cost. Although the performance of the equipment has improved over time, the variables in the formula have not been updated in a timely manner. Therefore, this paper has analyzed the preceding research, and performed several site visits to measure the cycle time of a backhoe and a loader. Construction equipment production rates were calculated with collected cycle times and variables given in 'Standard Unit Labor'. In addition,production rates were estimated considering the circumstances of various sites with the simulation program 'crystal ball.'

• Archives of design research
• /
• v.15 no.2
• /
• pp.213-222
• /
• 2002

A transfer paper, is needed in the third firing, is usually utilized for industrial ceramics in order to produce tablewares or promoting products. Products may have the same form, however; the price might be different by what kinds of design have transferred. We need to fully understand these methods in order to create high value and quality. Remodeling, the so-called second architecture, results from social Needs for renovation of structures and changing functions. Tile satisfying the need for a custom-made design which fits the features of a space. Most importantly, the remodeler must make an individual design ordered for the customer with an emphasis on economy and time efficiency. Tiles currently in the market are mass-produced using an automated system with a high-priced mold. It is difficult to find tiles of distinct design that are made in a small quantity. We need to develop a method for making various kinds of tile designs that would be marketed for the remodeling industry. In this study, after designing a certain wall with the tiffs in the space, 1 will talk about developing a method to make transfer paper to produce individual tiles for the space. 1 hope that the functional and aesthetic effect on remodeling will gain in popularity, and that we will foster a new demand for tiles in harmony with the other materials mentioned in this study.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1450-1451
• /
• 2015

우리나라는 지난 '96년 제정한 "전력기술관리법"에 따라 전력시설물 공사에 대한 설계와 감리업무를 실시하고 있지만 "전기공사업법", "정보통신공사업법" 등에서처럼 건축 등 타 분야와의 분리발주를 명확하게 명시하고 있지 않아 발주자, 시공자, 용역업자 등 업계의 혼란을 가중시키고 있어 많은 문제점을 야기시키고 있는 것이 현실이다. 분리발주는 통합발주에 비해 각 공정별 기술력을 확보하고 중소업체와 대형업체간의 공정한 경쟁을 유도함으로써 전력산업 시장경제의 건전성을 확보하는 등 통합발주로 인해 발생시키는 불법하도급, 업계의 혼란, 타 분야와의 경쟁력 약화 등 부정적인 요소를 해결할 수 있는 방안이다. 하지만 법상에서 명확하게 명시하고 있지 않아 모든 전기설계 감리 용역에 대해 분리발주가 되고 있지 않은 것이 현실이므로 거시적 관점에서 전력산업의 미래를 본다면 분리발주가 필요할 것으로 사료된다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.10
• /
• pp.143-150
• /
• 2009

The bar-shaped electrode is very popular in earth construction for its easy obtainments of the regulative grounding resistance values on power distribution systems in many countries. For these reason, a lots of researches are being proceeded on its deformation and materials. But the grounding construction has limit for improvement the grounding resistance characteristics not only by the improvement of the driven electrode, because that the grounding characteristics are very sensitive to soils(hard, soft). This study is about the construction methods on which the driven electrode can be serially or parallely connected using by hollow screw rod for obtaining the regulative grounding resistance values. The experimental results show that the grounding resistance values are reduced more than 30[%] comparing with the other construction methods under the same conditions(earth resistance, numbers of driven electrode, construction method of serial and parallel, chemicals for reducing grounding resistance, water).