• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.413-421
• /
• 2004

In this paper, a structural analysis for the pressurized water reactor(PWR) spent nuclear fuel disposal canister which is deposited under the 500m deep underground is carried out to predict the creep deformation of the canister while the underground water and swelling bentonite pressure are applied on the canister. Usually the creep deformation may be caused due to the Pressure and the high heat applied to the canister even though additional external loads are not applied to the canister. These creep deformations depend on the time. In this paper, oかy the underground water and bentonite swelling Pressure are considered for the creep deformation analysis of the canister, because the heat distribution inside canister due the spent fuel is not simple and depends on time. A proper creep function is adopted for the creep analysis. The creep analysis is carried out during $10^8$ seconds. The creep analysis results show that the creep strains are very small and these strains occur usually in the lid and bottom of the canister not in the cast iron insert. A much smaller strain is found in the cast iron insert. Hence, the creep deformation doesn't affect the structural safety of the canister, and also the creep stress which shows the stress relaxation phenomenon doesn't affect the structural safety of the canister.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.388-394
• /
• 2019

This paper describes a design of security system-on-chip (SoC) that integrates a Cortex-M0 CPU with an AAW (ARIA-AES- Whirlpool) crypto-core which implements two block cipher algorithms of ARIA and AES and a hash function Whirlpool into an unified hardware architecture. The AAW crypto-core was implemented in a small area through hardware sharing based on algorithmic characteristics of ARIA, AES and Whirlpool, and it supports key sizes of 128-bit and 256-bit. The designed security SoC was implemented on FPGA device and verified by hardware-software co-operation. The AAW crypto-core occupied 5,911 slices, and the AHB_Slave including the AAW crypto-core was implemented with 6,366 slices. The maximum clock frequency of the AHB_Slave was estimated at 36 MHz, the estimated throughputs of the ARIA-128 and the AES-128 was 83 Mbps and 78 Mbps respectively, and the throughput of the Whirlpool hash function of 512-bit block was 156 Mbps.

• Tunnel and Underground Space
• /
• v.14 no.1
• /
• pp.69-77
• /
• 2004

Investigation of the time-dependent behavior of rock and the associated mechanisms are of key interest in long-term stability analysis of many engineering applications. In this study, creep tests were performed on Daejeon granite samples of 25.4mm diameter under uniaxial compression at varying stress levels. The effect of moisture was investigated by testing both air-dried and fully water-saturated samples. The creep behavior of Daejeon granite exhibited three distinctive stages of primary, secondary and tertiary creep. The ultimate strength of granite under a constant stress decreased considerably with time. Saturation and immersion of the test specimen in water markedly increased the total creep strain as well as the secondary creep rate. The experimental creep curves are fitted to Burger's model as well as two other empirical models suggested by previous researchers. A number of the parameters determined for each model are dependent on stress and influenced by the presence of water. Based on the experimental results, an empirical relation between the applied stress and the time-dependent strain is established separately for each air-dried and fully water-saturated Daejeon granite.

• 한국지구물리탐사학회:학술대회논문집
• /
• 2006.06a
• /
• pp.195-200
• /
• 2006

Laboratory creep experiments show that compaction of unconsolidated shale is an irrecoverable process caused by viscous time-dependent deformation. Using Perzyna's viscoplasticity framework combined with the modified Cam-clay theory, we found the constitutive equation expressed in the form of strain rate as a power law function of the ratio between the sizes of dynamic and static yield surfaces. We derived the volumetric creep strain at a constant hydrostatic pressure level as a logarithmic function of time, which is in good agreement with experimental results. The determined material constants indicate that the yield stress of the shale increases by 6% as strain rate rises by an order of magnitude. This demonstrates that the laboratory-based prediction of yield stress (and porosity) may result in a significant error in estimating the properties in situ.

• Journal of IKEEE
• /
• v.22 no.1
• /
• pp.38-45
• /
• 2018

An integrated cryptographic processor that efficiently integrates ARIA, AES block ciphers and Whirlpool hash function into a single hardware architecture is described. Based on the algorithm characteristics of ARIA, AES, and Whirlpool, we optimized the design so that the hardware resources of the substitution layer and the diffusion layer were shared. The round block was designed to operate in a time-division manner for the round transformation and the round key expansion of the Whirlpool hash, resulting in a lightweight hardware implementation. The hardware operation of the integrated ARIA-AES-Whirlpool crypto-processor was verified by Virtex5 FPGA implementation, and it occupied 68,531 gate equivalents (GEs) with a 0.18um CMOS cell library. When operating at 80 MHz clock frequency, it was estimated that the throughputs of ARIA, AES block ciphers, and Whirlpool hash were 602~787 Mbps, 682~930 Mbps, and 512 Mbps, respectively.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.1
• /
• pp.61-65
• /
• 2010

A commercially available soft PZT wafer that is poled in thickness direction is subjected to longitudinal tensile stress loading in both short and open-circuit conditions. Variations of electric displacement in thickness direction and in-plane strains are measured over time during the loading. Different material responses in the two electrical boundary conditions are explained by the effects of piezoelectrically produced internal electric field on linear material moduli and domain switching mechanisms. Finally, a free energy model of normal distribution is introduced to explain the observed creep behavior, and its predictions are compared with experimental observations.

• Proceedings of the Korea Multimedia Society Conference
• /
• 2002.05d
• /
• pp.781-785
• /
• 2002

다양한 정보들을 디지털화하여 여러 형태의 미디어로 표현함으로 인해 정보의 저장과 관리가 어렵고 이로 인해 자료의 처리효율이 떨어지거나 상호 교환과 편집 등이 용이하지 않다. 본 논문에서는 동영상 강의를 효율적으로 처리하기 위해 주 제어기, 어휘분석기, 마우스 및 구문 분석기, 변수 테이블, 명령어 관리기, 수치함수 관리기, 변수 관리기, 스크립터 편집기, 스크립터 브라우저 등을 체계적으로 정립하여 다양한 미디어 매체를 하나의 파일형식으로 변환함으로서 동영상 강의 시스템에서 미디어 자료 관리를 원활하게 하고, 미디어의 처리속도와 시스템의 부하를 줄이는 미디어 통합모듈의 알고리즘을 설계하고 구현한다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.12
• /
• pp.2165-2171
• /
• 1997

The analysis model is the infinite power law creep material containing the rigid inclusion with crack shape. The present analysis is performed using the complex pseudo-stress function method. The strain rate intensity factor is developed as new fracture mechanics parameter which represents the stress and strain rate distribution near a crack tip in power law creep material. The strain rate intensity factor is developed in terms of Kolosoff stress functions.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.408-415
• /
• 1998

The analysis model is the power law creep material containing an elliptical rigid inclusion subjected to the arbitrarily directional stress on infinite boudary. The stress analysis is performed using the conformal mapping function and complex pseudo-stress function. The stress distributions near an elliptical rigid inclusion are obtained with various ellipse shapes, strain hardening exponents and directions of applied stress.

• Nuclear Engineering and Technology
• /
• v.28 no.1
• /
• pp.17-26
• /
• 1996

The in-reactor fuel rod support conditions against the fretting wear-induced damage can be evaluated by residual spacer grid spring deflection or rod-to-grid gap. In order to evaluate the impact of fuel design parameters on the fretting wear-induced damage, a simulation methodology of the in-reactor fuel rod supporting conditions as a function of burnup has been developed and implemented in the GRIDFORCE program. The simulation methodology takes into account cladding creep rate, initial spring deflection, initial spring force, and spring force relaxation rate as the key fuel design parameters affecting the in-reactor fuel rod supporting conditions. Based on the parametric studies on these key parameters, it is found that the initial spring deflection, the spring force relaxation rate and cladding creepdown rate are in the order of the impact on the in-reactor fuel rod supporting conditions. Application of this simulation methodology to the fretting wear-induced failure experienced in a commercial plant indicates that this methodology can be utilized as an effective tool in evaluating the capability of newly developed cladding materials and/or new spacer grid designs against the fretting wear-induced damage.