• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.43-48
• /
• 2000

In this study, a small punch creep(SP-Creep) test using miniaturized specimen$(10{\times}10{\times}0.5mm)$ has been described for the development of the newly semi-destructive creep test method for high temperature structural components such as headers and tubes of boiler turbine casino and rotor and reactor vessel. The SP-Creep testing technique has been applied to 2.25Cr-1Mo(STBA24) steel used widely as boiler tube material and the creep test temperature are varied at $550^{\circ}C{\sim}600^{\circ}C$. The overall deformations of SP-Creep curves are definitely depended with applied load and creep test temperature and show the creep behaviors of three steps like conventional uniaxial creep curves. The steady state creep rate${\delta}_{ss}$ of SP-Creep curve for miniaturized specimen increases with increasing creep temperature, but the exponential value with creep loading is decreased. The activation energy$(Q_{spc})$ during SP-Creep deformation with various test temperatures shows 605.7kJ/mol that is g.eater than 467.4kJ/mol reported in uniaxial creep test. This may be caused by the difference of stress states during creep deformation In two creep test. But from the experimental results, e.g. SP-Creep curve behaviors, the steady state creep rate${\delta}_{ss}$ with creep temperature, and the exponential value(n) with creep loading, it can be summarized that the SP-Creep test may be a useful test method to evaluate the creep properties of the heat resisting material.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.1
• /
• pp.81-90
• /
• 2012

The indentation test, which is one of the testing methods for evaluating the mechanical properties of materials, can be applied to the evaluation of creep properties. Many studies related to the indentation creep test, however, have just focused on the characteristics of the steady-state creep, so there are wide discrepancies between the uniaxial test and the indentation test. To obtain accurate creep properties, it is therefore important to consider the effects of transient creep. In the present work, the Ogbonna et al.'s work on the spherical indentation test including the transient creep was expanded and applied to the conical indentation creep test. The characteristics of the transient creep were analyzed via finite element simulations and compared with those obtained through spherical indentation. Other effects, such as elastic strain, indenter shape, contact area, and representative strain, which have not been considered properly in prior studies on the creep test, are also discussed.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.3A
• /
• pp.221-228
• /
• 2010

External bonding of carbon fiber reinforced polymer (CFRP) sheets has been widely accepted as a popular method for strengthening of deteriorated RC structures. The long-term behavior of CFRP-strengthened RC structure is often affected by that of the interface between CFRP sheets and concrete. This study aims at applying a viscoelastic model to describe the creep behaviour of the adhesive layer bonding CFRP sheet to concrete, the CFRP-concrete interface. Reviews of available models on concrete creep behavior have been first carried out and then new FE analysis model is proposed. The proposed FE analysis model based on the maxwell model has been verified by previous experimental results. It is shown that the creep effect of interfacial adhesive layer is very important on the long-term behavior of concrete structures strengthened with CFRP.

• Tribology and Lubricants
• /
• v.14 no.3
• /
• pp.46-50
• /
• 1998

초고분자량 폴리에틸렌(Ultra-High Molecular Weight Polyethylene)은 인공관절 라이너에 쓰이는 대표적 생체재료이다. 초고분자량 폴리에틸렌의 변형과 마모에 영향을 주는 인자에 대한 기본적 연구를 위하여 본 연구에서는 미세구조 결정상의 정도와 결정구조 방향성에 따른 초고분자량 폴리에틸렌의 크리프 변형 및 마모 특성의 연구를 행하였다. 압출 제작된 초고분자량 폴리에틸렌 봉(extruded UHMWPE rod)단면의 중앙(center)부분과 원주(periphery)부분으로부터 각각 직사각형 및 원통형의 시편을 제작하여 크리프 실험과 마모 실험을 실시하였다. 원주 시편의 크리프 변형율은 중앙 시편의 크리프 변형율보다 11%크며(p<0.05), 마모량도 원주 시편이 중앙 시편보다 두 배나 큰 것으로 (p<0.05)관측되었다. 이 결고달로부터 초고분자량 폴리에틸렌의 크리프 변형과 마모가 미세 결정구조 방향성에 영향을 받는 것으로 나타났다.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.100-105
• /
• 1998

초고분자량 폴리에틸렌(Ultra-High Molecular Weight Polyethylene)은 인공관절 라이너에 쓰이는 대표적 생체재료이다. 초고분자량 폴리에틸렌의 변형과 마모에 영향을 주는 인자에 대한 기본적 연구를 위하여 본 연구에서는 미세구조 결정상의 정도와 결정구조 방향성에 따른 초고분자량 폴리에틸렌의 크리프 변형 및 마모 특성의 연구를 행하였다. 압출 제작된 초고분자량 폴리에틸렌 봉(extruded UHMWPE rod)단면의 중앙(center) 부분과 원주(periphery)부분으로부터 각각 직사각형 및 원통형의 시편을 제작하여 크리프 실험과 마모 실험을 실시하였다. 원주 시편의 크리프 변형율은 중앙 시편의 크리프 변형율보다 11% 크며 (p<0.05), 마모양도 원주 시편이 중앙 시편보다 두 배나 큰 것으로(p<0.05)관측되었다. 이 결과들로부터 초고분자량 폴리에틸렌의 크리프 변형과 마모가 미세 결정구조 방향성에 영향을 받는 것으로 나타났다.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.1
• /
• pp.47-52
• /
• 1996

This paper deals with a study on improvement of long-time creep life prediction of steam turbine rotor steels by using initial strain method as a new approach at high temperatures of 500 to 70$0^{\circ}C$ . The main result shows that the inital strain method could be reliably utilized to predict and evaluate the long-time creep life as creep rupture strength and that the predicting equation for long-time creep life under a certain creep stress at a certain high temperature could be empirically derived out from each initial instantaneous strain measured.

• Journal of the Korea Concrete Institute
• /
• v.16 no.2 s.80
• /
• pp.185-194
• /
• 2004

It is difficult to analyze and predict the long-term behavior of concrete structures and members under multiaxial stresses because most of existing researches on creep of concrete were mainly concerned about uniaxial stress state. Therefore, the main objective of this paper is the investigation of creep properties of concrete under multiaxial stresses. This paper presents experimental study on creep of concrete under multiaxial compression. Twenty seven cubic specimens($20{\times}20{\times}20 cm$) for three concrete mixes were tested under uniaxial, biaxial, and triaxial stress states. Creep strains were measured in three directions of principal stresses. Poisson's ratio at the initial loading was obtained, as was Poisson's ratio due to creep stain and Poisson's ratio due to the combined creep strain and elastic strain. These Poisson's ratios were approximately equal for each concrete mix. The Poisson's ratio at the initial loading and the Poisson's ratio for the combined strain Increased slightly as the strength of the concrete increased. In addition, the volumetric creep strain and deviatoric creep strain were linearly proportional to volumetric stress and deviatoric stress, respectively.

• Korean Journal of Materials Research
• /
• v.3 no.6
• /
• pp.575-584
• /
• 1993

The effects of atmosphere on the creep rupture properties of Ni-base superalloy Ren6 80 were investigated. Creep rupture tests were performed at $760^{\circ}C$, 657MPa and 982%, 157MPa under Ar gas atmospheres. Creep rupture mode and rupture properties (rupture life and elongation) were similar in two different atmospheres under the condition of $760^{\circ}C$, 657MPa. However, the results at $982^{\circ}C$, 157MPa showed different creep rupture mode and life between air and Ar gas atmospheres. In air, it was shown that creep cracks were initiated at surface-exposed grain boundaries and propagated along grain boundaries. In Ar gas atmosphere, the cracks were initiated at inner grain boundaries and coalesced to surface cracks which cause cup-and-cone type fracture. Due to protective oxide layer formation, air test showed longer rupture life than Ar test.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.291-299
• /
• 2003

The effect of temperature and soil confining stress on geosyntheic creep behaviour was studied by performing the temperature dependent confined creep tests for HDPE geogrid and geomembrane specimen. The visco-elastic creep coefficients of the geosynthetics were evaluated by the test results and it was proposed that the simple expressions for the instantaneous and limit creep strain of geosynthetics was considered as a function of temperature and confining stress on geosynthetics. Based on the time-temperature superposition principle, a master curve has been drawn for extrapolating tensile creep strains to longer time intervals(1$\times$10 $^7$min.∼1$\times$10$^{10}$min.). By using this master curves, the shift factors which can be used in establishing master curve considering confining stress on geosynthetics were carried out. Each tests was performed during 8,000∼12,000 min., with temperature ranging between 5$^{\circ}C$ and 4$0^{\circ}C$ and with confining stress ranging between 0 t/$m^2$ and 9 t/$m^2$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.4
• /
• pp.447-452
• /
• 2011

It is well known that the dominant damage mechanisms in high-temperature steam turbine facilities such as rotor and casing are creep and fatigue damages. Even though coupling of creep and fatigue should be considered while predicting the life of turbine facilities, the remaining life of large steam turbine facilities is generally determined on the basis of creep damage because the turbines must generate stable base-load power and because they are operated at a high temperature and pressure for a long time. Almost every large steam turbine in Korea has been operated for more than 20 years and is made of steel containing various amounts of principal alloying elements nickel, chromium, molybdenum, and vanadium. In this study, creep damage model of 1Cr1Mo1/4V steel for turbine rotor is proposed and that can assess the high temperature creep life of large steam turbine facilities is proposed.