• 대한기계학회논문집A
• /
• 제35권4호
• /
• pp.447-452
• /
• 2011

일반적으로 화력발전 터빈 로터나 케이싱과 같이 고온 고압에서 운전되는 설비의 경우 크리프 및 피로 손상이 주된 손상기구로 알려져 있다. 터빈 설비의 수명을 정확하게 예측하기 위해서 크리프 및 피로 손상 기구를 복합적으로 고려해야 하지만 500MW 급 대용량 터빈 설비의 경우 기저 부하를 담당하기 때문에 기동횟수가 많지 않고 고온에서 장시간 동안 안정적인 운전을 하므로 잔여수명을 결정할 때 크리프 수명을 주로 사용한다. 국내에서 20 년 넘게 운전되고 있는 대용량 터빈의 경우 대부분 니켈, 크롬, 몰리브덴, 바나듐 성분이 포함한 재료로 되어 있다. 본 논문에서는 대용량 터빈의 크리프 수명을 예측하기 위하여 1Cr1Mo1/4V 터빈 로터강에 대한 크리프 손상 모델을 제안하고자 한다.

• 한국압력기기공학회 논문집
• /
• 제11권1호
• /
• pp.33-38
• /
• 2015

The effects of post weld heat treatment(PWHT) on the mechanical properties of 2.25Cr-1Mo steels were investigated. As the PWHT temperature or holding time increased, the strength of low alloy steels progressively decreased due to softening process. After the conventional PWHT, the strength was larger than the minimum value of materials specification. The Charpy impact energy was hardly affected by the conventional PWHT. The trend of mechanical properties was analyzed in terms of tempering parameter. Most materials replaced from a power plant met the requirements of materials specification except for one heat. Same heat of materials with low impact energy were attributed to the voids formed during casting process.

• 한국생산제조학회지
• /
• 제19권5호
• /
• pp.631-636
• /
• 2010

SNCM420 steel is one of the cam shaft materials which are used in the supply unit for ship engine cam shaft. In this study the assessment of cutting behavior was conducted for the SNCM 420 steel and SM45C steel with various cutting conditions as depth of cut 0.5, 1.0, 1.5, 2.0mm and feed rate 0.1~0.3m/rev. The controlled chip was produced in feed rate 0.2, depth of cut 1.0 for SNCM420 and feed rate 0.2, depth of cut 2.0 for SM45C. There is no difference cutting force between SM45C and SNCM420 steels.

• 한국기계가공학회지
• /
• 제17권3호
• /
• pp.148-154
• /
• 2018

When shooting small arms, the inner surface temperature is heated up to about $700{\sim}1,000^{\circ}C$ by the friction of the bullet and the inner wall of the barrel and the combustion of propellant. High-temperature propellant gas and high-speed movement of the bullet cause corrosion of the inner wall, which is noticeable immediately in front of the chamber. In this study, the mechanical properties of Cr-Mo-V steel, which is the base material, were tested using Taguchi experimental design to find the best nitriding treatment conditions. For the nitriding process, the working time, salt bath temperature, and salt concentration were combined as three conditions and placed in the $L_9(3^4)$, orthogonal array table. The thicknesses of the white layer and the nitrogen diffusion layer were measured after nitriding under each condition in a salt bath furnace. Durability was evaluated by measuring the degree of dispersion through actual shooting because it was difficult to evaluate the mechanical properties of the cylinder inner structure. As a result, it was confirmed that the durability was optimal at $565^{\circ}C$, 1 hour, 0.5%. These optimal conditions were selected by the statistical analysis of the Minitab program(ver.17).

• 한국해양공학회지
• /
• 제19권1호
• /
• pp.49-56
• /
• 2005

In spite of the merits of laser welding being able to obtain the high welding quality such as smaller width of melting and heat affected zone, smaller welding deformation and fine grains of weldment compared to arc welding, laser welding is mainly used in joining of thin steel parts of electronics industry. Laser welding is getting widely used in joining thick plate and special kinds of steel due to its high power. While the arc welding is still applied for 2.25Cr-1Mo steel which is the essential material of atomic power generation equipment, the laser welding is not yet applied despite its high quality. So it has a trial to a special case demanding high welding quality such as atomic power plant. Accordingly, in this research, the mechanical properties of weldments by arc and laser welding were investigated using FEM to confirm the applicability of laser welding to 2.25Cr-1Mo steel. The Charphy test was carried out to understand the effect on the fracture toughness of weldments. The results of examination and test of the mechanical properties showed the validity of this research.

• 한국산학기술학회논문지
• /
• 제16권3호
• /
• pp.1645-1651
• /
• 2015

본 연구에서는 선삭 작업에서 가공 여유각 변경에 따른 피삭재의 형상정밀도가 어떻게 변화되는지 분석하고자 하였다. 피삭재는 3가지로 SM45C(기계구조용탄소강), SCM415(크롬몰리브덴강), STS303(스테인리스강)을 선택하여 정해진 가공조건인 회전속도 2,500 rpm으로 시작하여 이송속도 0.07 mm/rev와 0.10 mm/rev를 기준으로 가공깊이 0.1 mm, 0.2 mm, 0.3 mm 그리고, 절인 경사각인 네거티브 경사각 $0.0^{\circ}(-6.0^{\circ})$, $0.3^{\circ}(-6.3^{\circ})$, $0.9^{\circ}(-6.9^{\circ})$의 3가지 형태로 가공하였을 경우, 재료별 가공정밀도, 원통도, 동축도, 진원도 등의 결과를 비교 분석하였다. 피삭재의 재질별로 알아본 원통도의 정밀도는 $0.0^{\circ}{\rightarrow}0.3^{\circ}{\rightarrow}0.9^{\circ}$의 순으로 $0.9^{\circ}$일 경우가 가장 좋은 원통도 값을 나타냈다. 결과적으로 바이트의 네거티브 경사각이 커지면 정밀도가 특정 부분에서 재질에 관계없이 좋아져서 가공성이 향상됨을 알 수 있었다. 또한, 이송속도와 절삭 깊이에 따라 가공형상이 변화한다는 것과 재질에 따라 다르게 적용되어야 한다는 것을 확인하게 되었다.