• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.05a
• /
• pp.16-21
• /
• 2000

In this paper we design a GA-fuzzy controller for position control and anti-swing at the destination point. Applied genetic algorithm is used to complement the demerit such as the difficulty of the component selection of fuzzy controller namely scaling factor membership function and control rules. lagrange equation is used to represent the motion equation of trolley and load in order to obtain mathematical modelling. Simulation results show that the proposed control technique is superior to a conventional optimal control in destination point moving and modification.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2000.05a
• /
• pp.28-35
• /
• 2000

For the merit of a container in transportation and cargo handling the amount of container freight has been continuously on the increase. On the other hand container crane had got the bottle neck in cargo handling due to low productivity so that freight congestion had been often occurred at ports. in this paper A mathematical model for container crane system is represented a method for designing a fuzzy controller of container crane system for high productivity in cargo handling is presented. The fuzzy controller is compared with other optimal controller at the same condition. in the computer simulation the fuzzy controller obtained an excellent response to reference change better than the optimal controller. For disturbance such as a strong storm and parameter change due to change of cargo weight the result was also stable and robust than the optimal controller.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1471-1474
• /
• 2003

The correlation between the object function and the design parameter is shown on this paper by using the characteristic function for tile mixed result of the structure analysis. tile buckling analysis and the table of orthogonal array according to the original crane's dimensional change. About the above two object functions, the effective of design change according to the change of design parameters could be estimated. Also, the crane's weight is reduced up to 20.58 percent maintaining the structural stability according to the thickness of plate.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.5
• /
• pp.544-553
• /
• 2002

The recent amount of container freight continuously has been increased, but the low efficiency of container crane causes jamming frequently in transportation and cargo handling at port. It is required that the working velocity and safety are improved by control of moving the trolley as quick as possible without large overshoot and any residual swing motion of container at the destination. In this paper, a LQ controller for a container crane is proposed to accomplish an optimal design of improved control system for minimizing the swing motion at destination. In this scheme a mathematical model for the system is obtained in state space form. Finally, the effectiveness of the proposed controller is verified through computer simulation.

• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.4
• /
• pp.502-508
• /
• 2000

The amount of container freight is continuously increasing recently, but freight congestion problem frequently occurs at ports due to low efficiency of container crane in transportation and cargo handling. In this paper, a method for designing a fuzzy controller of the container crane system is presented. In this scheme a mathematical model for the system is obtained in state space representation. The response of the proposed fuzzy controller is compared with that of the optimal controller at the same condition. Through the simulation results, the performance of the fuzzy controller was observed better than that of optimal controller in respect of reference change, disturbances and parameter change. The fuzzy controller was also more stable and robust than the optimal controller.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.4
• /
• pp.624-629
• /
• 2008

This paper presents a scheme for designing a state observer for container cranes. If the system is completely observable with a given set of outputs, then it is possible to determine the states that are not directly measured. We consider the reduced-order states observer with only trolley position detection and with trolley position and container angle detection. The gain matrix of the each state observer is adjusted using a RCGAs. A set of simulation works is carried out to demonstrate the effectiveness of the proposed scheme.

• KIEAE Journal
• /
• v.7 no.6
• /
• pp.83-90
• /
• 2007

A mobile crane has been more frequently used to deal with the increased capital-intensive projects in line with the economic growth, but the operation is still heavily dependent on personal experience in the past, resulting in severe overturn accidents that cause the loss of lives and damage to the properties. A crane shall be installed in a systematic manner that proved to be safe in engineering aspect, and should the installation and operation be blindly dependent on experience alone, it would apparently cause a great risk. Particularly the mobile crane, among others, frequently causes a severe overturn accident due to poor ground-fixing device. The study therefore focused on fixing system of mobile crane and the outcome is highly expected to make a great commitment to selecting the optimal type of crane for the project as well as to securing the safety during construction.

• Journal of Navigation and Port Research
• /
• v.31 no.8
• /
• pp.705-710
• /
• 2007

The productivity of automated container terminals is significantly affected by not only the speed related performances of automated transfer cranes(ATCs) but also the sizes of container blocks. In this paper, it is discussed how to determine the size of import container blocks considering both the container handling times of an ATC and their storage space. Firstly, evaluation models are suggested for the container handling times of an ATC in a typical import container blocks. Secondly, three mathematical formulations are suggested to determine the size of import container blocks. Numerical experiments for the suggested models to determine the size of import container block are provided.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.6
• /
• pp.526-532
• /
• 2008

Structure evaluation for 70/15 $T{\times}105\;m$ LLC(Level Luffing Crane)'s boom was conducted by Finite Element Method. Boom modeled with beam element was fixed by luff rope and boom mount and was received loads from self weight, luff hoisting, traveling motion, slewing motion, and wind force, etc. These applied loads were calculated using various factors presented in the reference standards and were inputted in the analysis model after considering about the adverse conditions of LLC. In the research, deformation, stresses, buckling of boom were evaluated by ANSYS. Structural safety of boom was confirmed in the results of numerical analysis.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.19 no.6
• /
• pp.776-781
• /
• 2010

Optimum design of movable hydraulic crane's booms for weight reduction was performed in this study. Since the boom weight of the present used booms is very heavy, it is needed to make them lighter structure as possible as we can. Optimum design was performed for the booms by changing from the hexagonal cross section to triangular truss structure under the conditions, which are the allowable stress for the present cross section must be maintained, and the optimized weight must be minimized. CATIAV5 was used for stress analysis and design variables were established as the height and width of the triangular truss structure. As the results, it is found that the height of the truss structure is increased in proportion to the height of the booms and the maximum stress for optimal truss structure was obtained as 412MPa, which is lower than the allowable stress for the present hexagonal cross section. The optimized weight of the booms is reduced to about 19.88% comparing to the original weight.