• Journal of the Korean Society for Railway
• /
• v.12 no.4
• /
• pp.590-596
• /
• 2009

In this study, the failure modes and energy absorption characteristics of four different kinds of circular tubes made of carbon, glass, Kevlar and carbon-Kevlar hybrid fibres composites with epoxy resin have been evaluated. To achieve these goals, compressive tests were conducted for the tubes under 10mm/min loading speed. Based on the test results, the carbon/epoxy tube showed the best energy absorption capability, while carbon-Kevlar/epoxy tubes were worst. In the failure mode during crushing, both of the carbon/epoxy tubes and the glass/epoxy tubes were crushed by brittle fracturing mode. The Kevlar/epoxy tubes were collapsed by local buckling mode like steel, while the carbon-Kevlar hybrid tubes were collapsed by mixed mode of local buckling and lamina bending.

• The tire
• /
• s.116
• /
• pp.22-30
• /
• 1985

전년 9~10월호에서는 케블라의 종류,용도, 경제성,미세구조, 제법, 내열성 ,치수안전성 등에 대해 설명하였으나, 이번 호에서는 습ㆍ건열열화, 피로성, 동적점탄성 등에 대해서 살펴보고자 한다.

• The tire
• /
• s.114
• /
• pp.37-46
• /
• 1984

• Proceedings of the Korean Fiber Society Conference
• /
• 1991.06b
• /
• pp.75-75
• /
• 1991

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.10b
• /
• pp.215-216
• /
• 2003

섬유강화 복합재료(FRC:Fiber Reinforced Composites)는 기존의 금속재료에 비해 높은 비강도, 비강성의 특성으로 인해 자동차, 항공산업 등 폭 넓은 응용 범위에 적용되고 있다. 특히 직물 복합재료(Fibric Composites)는 취급이 용이하고, 유연성이 높기 때문에 복잡한 형상을 가지는 금형에 적용하기가 수월하다. 하지만 아직까지는 금형의 형상에 있어서 제약을 받고 있다. (중략)

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.403-404
• /
• 2001

In conventional heating, the heat source causes the molecules to react from the surface toward the center so that successive layers of molecules heat in turn. In the microwave heating, which is produced a volume heating effect, all molecules are set in action at the same time. And, It also evens temperature gradients without the concern of material thickness. (omitted)

• Composites Research
• /
• v.20 no.3
• /
• pp.17-24
• /
• 2007

In this study, the failure modes by ballistic impacts were studied both for a neat Kevlar woven fabric and a Kevlar liquid armor impregnated with shear thickening fluid (STF) containing silica particles. These two materials showed quite different failure modes macroscopically in ballistic impacts tests used by Cal.22 FSP and 9mm FMJ bullet. Yarn pull-out for the neat Kevlar woven fabric and yarn fracture occurred partially through all plies from 1st ply to last one for the STF-Kevlar are an important energy absorption mechanisms. The results observed by S.E.M showed commonly fiber damage which are torn skin in the longitudinal fiber direction, fiber split axially and fiber fracture for two materials. The reasons why STF-kevlar liquid armor material exhibits excellent ballistic performance are as follow: firstly the increased friction forces between yarn-yarn and fabric-fabric covered with silica particles and secondary the evolution of shear thickening phenomenmon resulting in suppression of yarn mobility.

• Composites Research
• /
• v.22 no.6
• /
• pp.32-38
• /
• 2009

In this study, the energy absorption capabilities and failure modes of four different kinds of circular tubes made of carbon, Kevlar and carbon-Kevlar hybrid composites with epoxy resin have been evaluated. In order to achieve these goals, these tubes were fabricated with unidirectional prepregs and compressive tests were conducted for the tubes under 10mm/min loading speed. From the test results, carbon/epoxy tubes were collapsed by brittle fracturing mode and showed the best energy absorption capabilities, while Kevlar/epoxy tubes were crushed by local buckling mode and worst. The hybrid [$90_C/0_K$] tubes were failed in a local bucking mode and showed good post crushing integrity, whereas [$90_K/0_C$] tubes were failed in a lamina bending mode and bad post crushing integrity.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.128-134
• /
• 2014

A Experimental study on frequency characteristics of the microphone array covered with Kevlar in closed test section wind tunnel. Microphones that are flush mounted in a closed test section wall of wind tunnel are subject to very high flow noise resulting from the turbulence in the wall boundary layer. At this time the microphones measure the strong hydrodynamic fluctuations generated by the flow. The phenomena are referred to a microphone self-noise and a method for reducing this has studied. In this paper the array that covered with acoustically transparent Kevlar sheet was designed and made to reduce the flow-induced self-noise. For the validation frequency characteristics of the Kevlar, the microphone array was installed on the wall and test was performed for white noise and sine wave of several frequencies using loudspeaker. In addition, the paper compared the signals as a tension of Kevlar. The results were presented that tend to decrease the sound pressure level at high frequency above 3500Hz according to existence of Kevlar.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2002.05a
• /
• pp.48-52
• /
• 2002

This paper describes the need for a ductile Fiber Reinforced Plastic(FRP) reinforcement for Concrete Structures. Using the material hybrid and geometric hybrid, it is demonstrated that the pseudo-ductility Characteristic can be generated in FRP rebar. Ductile hybrid FRP bars were successfully fabricated at Ø3mm and Ø10mm nominal diameters using the braidtrusion process. Tensile and bending specimens from these bars were tested and compared with behavior of stress-strain of steel bar and GFRP rebar