• Food Science and Preservation
• /
• v.17 no.1
• /
• pp.151-159
• /
• 2010

Changes in volatile organic compounds were investigated during storage after electron beam irradiation. Grapes were irradiated at 0.25, 0.5, 0.75, and 1.0 kGy and stored for 1 month at $4^{\circ}C$. Butanol, hexanal, [E]-2-hexenal, hexanol, and 3-methyl-butanol were the major volatile organic compounds of grapes. The types of volatiles in irradiated grapes were similar to those of non-irradiated samples but concentration differed among treatments. Some volatile compounds decreased during storage, whereas others, especially the esters, increased. Concentration of most volatile compounds were higher in pre-stored grapes than in post-stored fruit (thus, during the 30 days after irradiation by e-beam). Consequently, concentration of volatile organic compounds either increased or decreased after e-beam irradiation but these changes did not correlate with irradiation dose.

• Journal of Power System Engineering
• /
• v.13 no.6
• /
• pp.88-94
• /
• 2009

In this paper, vibration characteristics after applying variable speed control to fans with a rated speed used in a power plant are studied by performing experiments and analyzing finite element models. Then the campbell diagram is presented to verify the reason of the abnormal vibration measured from fan structure during variable operation of Forced Draft Fan & Induced Draft Fan. According to results, it is found that amplitude of acceleration increases abruptly when a 2X harmonic component meets the natural frequency of fan rotor. Therefore it is very important thing that investigate exactly dynamic characteristics for the rotor at variable speed zone before applying variable speed control to a rotor with a rated speed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.803-806
• /
• 2002

This paper estimated the stability of centrifuge as its rotating speed compared with the natural frequency of cylinder and screw by finite element analysis. It shows that the one of exciting causes is the tooth passing frequency of input and output parts by the periodic characteristics of transmission error due to an planetary gear having three stages. Also, it proposed the critical speed of cylinder and screw by the Campbell diagram.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2011.10a
• /
• pp.764-765
• /
• 2011

In this paper, rotordynamic analyses of the Campbell diagram, critical speeds, and harmonic responses for a TMP rotor system are performed. Since the finite element model of the TMP rotor system has a very large number of degrees of freedom because of its complex geometry, and dynamic analyses for investigating the critical speeds, stability, and harmonic response are repeated for various design parameters, model order reduction (MOR) is necessary to reduce the computational cost. The Krylov-based model order reduction via moment matching significantly speeds up the rotordynamic analyses for the TMP rotor system.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.262-265
• /
• 2006

The purpose of this study is to design 200 kW, 15,000 rpm 3 phase induction motor. This research deals with natural frequency and mode shape of rotating shaft of 3 phase induction motor with bearing stiffness by finite element analysis. We present natural frequency characteristic variation of rotating shaft according to change bearing stiffness. Also we are verified stability of rotating shaft from backward and forward critical speed by campbell diagram.

• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.6
• /
• pp.78-85
• /
• 2007

In this study, we performed finite element analysis for the design of a medical centrifuge and two-types of centrifuge were compared with each other. The types of centrifuge are 2-arm straight type and 3-arm type. Structural analysis was done with respect to the change of the rotational speed of the rotor of a centrifuge. When the rotor of centrifuge was rotated, the von Mises stress of 2-arm straight type-rotor was compared with the von Mises stress of 3-arm type. The margin of safety was estimated from the result. We found the critical speed of centrifuge from the campbell diagram by modal analysis.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2015.07a
• /
• pp.82-84
• /
• 2015

유한요소법을 이용하여 카페리선 제작 시 축계의 제작 및 강도의 문제를 Campbell Diagram 및 Modal 해석을 통한 동특성 분석을 하였다. 이를 통하여 양방향 차도선의 추진 방향 및 후진 방향 축계 작동 시 공진 현상 및 위험속도를 분석 결과 안정성을 보인 것으로 판단된다.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.5
• /
• pp.329-336
• /
• 2015

This paper presents a sorting method of mode vectors and natural frequencies about a rotor-journal bearing system. The rotor is solved by the finite element method, the bearing stiffness and damping coefficient are solved by the finite difference method. At any rotation speed section through the eigenvalue analysis of the system, mode vectors and natural frequencies not sorted are confirmed via the Campbell diagram and the MAC(modal assurance criterion). To sort mode vectors and natural frequencies of the section, a mode sorting method is presented through a method of rearranging the MAC of the mode vectors. Finally, the mode vectors and the natural frequencies are sorted by using the presented method, these are verified through the MAC.

• Journal of Hydrogen and New Energy
• /
• v.24 no.6
• /
• pp.566-572
• /
• 2013

In the present study, structure analysis has been performed to understand the deflection and stress distribution for a hybrid street-lamp having a vertical-axis wind turbine and a photovoltaic panel. Modal analysis is also evaluated to avoid resonance gerenerated by sychronism between a turbine and a lamppost. To analyze deflection, stress and frequency, general analysis code(ANSYS-Mechanical 13) is employed in the present work. Throughout structure analysis in the hybrid street-lamp, maximum stress is observed at the connecting position between a turbine blade and a blade supporter. Campbell diagram which is combined the natural frequency of turbine blades and blade passing frequency is presented to analyze a system resonance. It is found that the resonance of the system having a rotating turbine blade and a lamppost can avoid by the optimal selection of geometric parameters of a wind turbine.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1057-1067
• /
• 2010

Vibration and noise analysis as well as strength of gear teeth, gear profile design are considered in order to develop the multi-gear train devices of synchro system for the guns of a warship. A new approach to the critical speed calculation of practical industrial multi-mesh geared system is presented. A transfer matrix model based on Hibner's branch method is developed and the natural properties of the branched rotor system are calculated with using the ${\lambda}$-matrix formulation. A Campbell diagram, in which the excitation sources caused by the mass unbalance of the rotors and the transmitted errors of the gearing are considered, shows that, at theoperating speed, there are not the critical speed.