• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.9B
• /
• pp.1635-1640
• /
• 2000

In this paper, a 18 GHz oscillator is designed with the push-push method an fabricated by semi-MMIC process, in which the second harmonic is the main output signal with the suppressed fundamental mode. In semi-MMIC process, passive components with microstrip transmission line are implemented using MMIC process on semi-insulating GaAs substrate. Then, chip types of P-HEMT, resistors, and capacitors are connected through Au wire-bonding. Also, the ground plane is inserted around the circuit and connected each other with the back-side of substrate through Au wire-bonding instead of via-hole. The semi-MMIC push-push oscillator shows the output powder of -10.5 dBm, the fundamental frequency suppression of -17.3 dBc/Hz, and the phase noise of -97.9 dBc/Hz at the offset frequency of 100 kHz.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.642-647
• /
• 2012

$TiO_2$ thin films for a pulse power capacitor were deposited by RF magnetron sputtering. The effects of the deposition gas ratio and thickness on the crystallization and electrical properties of the $TiO_2$ films were investigated. The crystal structure of $TiO_2$ films deposited on Si substrates at room temperature changed to the anatase from the rutile phase with an increase in the oxygen partial pressure. Also, the crystallinity of the $TiO_2$ films was enhanced with an increase in the thickness of the films. However, $TiO_2$ films deposited on a PET substrate showed an amorphous structure, unlike those deposited on a Si substrate. An X-ray photoelectron spectroscopy(XPS) analysis revealed the formation of chemically stable $TiO_2$ films. The dielectric constant of the $TiO_2$ films as a function of the frequency was significantly changed with the thickness of the films. The films showed a dielectric constant of 100~110 at 1 kHz. However, the dissipation factors of the films were relatively high. Films with a thickness of about 1000nm showed a breakdown strength that exceeded 1000 kV/cm.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.91-95
• /
• 2002

A very small size BPF is realized using LTCC Multilayer technology. A λ/4 resonator with shunt-to-ground loaded capacitor is used to shorten resonator length and achieve higher qualityfactor. Also this resonator enable BPF to improve out-of-band rejection. Coupling coefficients between coupled stripline resonators and external qualityfactor of a resonator are derived and apply to the filter design. The measured results show a good agreement with the simulation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.1
• /
• pp.93-102
• /
• 1998

This paper describes to control system for AC to DC converter which has been widely used to power source in industrial factory and domestics. In this paper, three-phase PWM AC to DC Boost converter that operates with unity power factor and sinusodial input line currents is presented. The current control of this converter is based on the predicted current control strategy with fixed switching frequency and the line currents track to reference currents within one sampling time interval. By using this control strategy low ripples in the output current and the voltage as well as fast dynamic response are achieved with small dc link capacitance employed.ployed.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.241-250
• /
• 2000

Chua's circuit is a simple electronic network which exhibits a variety of bifurcation and attractors. The circuit consists of two capacitors, an inductor, a linear resistor, and a nonlinear resistor. In this paper, a transmitter and a receiver using two identical Chua's circuits are proposed and synchronizations and secure communication of a lossy equivalent transmission are investigated. Since the synchronization of the lossy equivalent transmission system is impossible by coupled synchronization, theory having both the drive-response and the coupled synchronization is proposed. The proposed method is synthesizing the desired information with the chaos circuit by adding the information signal to the chaos signal in the lossy equivalent transmission system.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1285-1287
• /
• 2004

본 논문은 20kV 10kW급 고전압 직류 전원장치와 원격제어기의 개발에 대해서 기술하고 있다. 개발된 고전압 직류 전원장치는 다양한 고전압 시스템에 적용하기 위해서 출력전압이 최대 20kV까지 가변 가능하도록 설계되었으며 먼저, 펄스파워 시스템에 필요한 고전압 캐패시터 충전용 전원장치로서 사용하여 동작특성과 신뢰성을 확인하였다. 고전압 직류 전원장치는 단상 고주파 공진형 인버터 방식을 채용하였으며 스위칭 주파수를 최대 100kHz까지 가변시켜 출력전류를 제어하였다. 또한 인버터 출력이 인가되는 고전압 변압기에 2대의 단상 변압기를 사용하여 각각의 출력부담과 전기적 절연내력을 낮출 수 있었다. 한편, 고전압 시스템에 적용 할 때, 조작자의 안전성을 높이고 동작상태를 실시간으로 진단하기 위해서 원격제어기를 개발하였으며 다양한 조건에서의 시뮬레이션과 실험을 통해 개발된 고전압 전원장치와 원격제어기의 동작특성을 확인하였다

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.55 no.1
• /
• pp.1-5
• /
• 2006

The effect of A/B moi ratios and sintering temperatures on dielectric properties and microstructure of $(Ba_{0.93}Ca_{0.07})_m(Ti_{0.82}Zr_{0.18})O_3$ ceramics were investigated. The dielectric constant decreased with increasing the A/B mol ratio. However, the dielectric loss is improved. As the dielectric properties of A/B mol ratio with m = 1.009 at sintered temperature $1260^{\circ}C$, we obtained dielectric constant 12,800, dielectric loss $3.5\%$ and Y5V temperature characteristics. Highly reliable Ni-MLCCs, 1.6mm$(length){\time}0.8mm(width){\time}0.8mm$(height) with capacitance of 1.23 ${\mu}F$ and 야ssipation loss of $5.2\%$ were obtained employing dielectric material composed of $(Ba_{0.93}Ca_{0.07})_{1.009}(Ti_{0.82}Zr_{0.18})O_3$ - $MnO_2\;0.2wt\%-Y_2O_3\;0.18wt\%,\;-\;SO_2\;0.15wt\%-(Ba_{0.4}Ca_{0.6})SiO_3\;1wt\%$.

• Electrical & Electronic Materials
• /
• v.10 no.7
• /
• pp.674-681
• /
• 1997

Ternary compound ceramics, (1-y-x) BaTiO$_3$-y SrTiO$_3$-x MgTiO$_3$(0.00 x 0.20), were fabricated by the conventional ceramic process. The structural and dielectric properties of specimens were investigated while varying the composition and sintering temperature(1,200~1,45$0^{\circ}C$) in order to obtain the optimum condition of capacitor. As is well known, Curie temperature(T$_{c}$) of high dielectric-based ceramic(BaTiO$_3$) was shifted and temperature of capacitance was decreased in according to increase of solid solution with (Sr, Mg)TiO$_3$. As a result, a suitable condition of compound rate for capacitor was obtained such as the BSM-11(0.8BaTiO$_3$-0.1SrTiO$_3$-0.1MgTiO$_3$), and sintering temperature was sintered at 1,25$0^{\circ}C$ for two hours. In this case, dielectric constant<1,300, dielectric loss(tan$\delta$)<0.03, and the variation rate of capacitance had less than 3% in the range -10~7$0^{\circ}C$.>.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.575-578
• /
• 2000

In this work, all solid-state thin film supercapacitor(TFSC) was fabricated using tungsten trioxide (WO$_3$) with a structure WO$_3$/LiPON/WO$_3$/Pt/TiO$_2$/Si (substrate). After TiO$_2$ was deposited on Si(100) wafer by d.c. reactive sputtering, the Pt current collector films were grown on TiO$_2$glue layer without breaking vacuum by d.c. sputtering. Fabrication conditions of WO$_3$ thin film were such that substrate temperature, working pressure, gas ratio of $O_2$/Ar and r.f. power were room temperature, 5 mTorr, 20% (O$_2$(8sccm)/Ar(32sccm)) and 200W, respectively. LiPON electrolyte film were grown on the WO$_3$ film using r.f. magnetron sputtering at room temperature. The XRD pattern of the as-deposited WO$_3$ thin film were shown no crystalline peak (amorphous). The SEM image of as-deposited WO$_3$ thin film showed that the surface is smooth and uniform. The capacitiy of as-fabricated TFSC was 0$\times$10$^{-2}$ F/$\textrm{cm}^2$-${\mu}{\textrm}{m}$.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2000.11a
• /
• pp.22-22
• /
• 2000

DRAM의 고접적화에 따라 기존의 반도체 공정에서 사용중인 여러 가지 기술들이 대부분 그 한계를 보이고 었으며, 대표적인 것이 캐퍼시터 형성기술이다. 따라서 1G DRAM급 이상의 초고집적 회로를 실용화하기 위해서 유전율이 높은 BST ($BrSrTiO_3$) 박막을 이용하여 캐패시터를 제조하려는 기술도 반드시 해결되어야 현재 활발히 실용화 연구가 진행중에 있다. BST 박막을 제조하는 방법은 RF magnetron sputtering, Ion beam reactive co-evaporation, LSM (Liquid Source Misted) CVD, MOCVD 등의 법으로 제조되고 있다. 본 연구에서는 전기-수력 학적 분무(Electro-Hydrodynamic Spray)현상을 이용한 MOCVD에 BaO, SrO, $TiO_2$ 박막을 증착 하여 전기장세기, 기판온도, 시간 등에 따른 특성을 조사하였다. 전기수력학적 분무를 이용한 증착법은 원료를 함유하는 용액을 이용함으로써 이송관의 가열이 필요 없이 장치를 간단하게 할 수 있고, 용액의 유량과 전기장의 세기에 따라 초미세 입자제어도 가능하며, 박막의 조성을 출발 용액으로 부터 조절하는 등의 특징을 가지고 있다. 증착한 박막의 표면, 단면 형상 및 조성을 분석하였고 결정화 여부 및 우선 배향성을 조사하였다. 현재는 개별 박막의 표현 형상과 조성에 대한 연구 결과를 얻었으며, 계속해서 박 막의 여러 특성에 대하 연구할 계획이다.