• KSBB Journal
• /
• v.21 no.4
• /
• pp.255-259
• /
• 2006

The biodegradable hyaluronic acid(HA) membranes cross-linked with lactide using the crosslinking agent, 1-ethyl-3(3-dimethyl aminopropyl) carbodiimide(EDC) were prepared as a potential biocompatible material for tissue engineering. HA membranes having different mechanical properties were synthesised by varying degree of the mole ratio of lactide to HA, EDC concentration, and crosslinking temperature. HA membranes were degradable in water solution and the degradation became slower with the increasing mole ratio of lactide to HA. HA membranes were sterilized using ethylene oxide gas and extracted with cell culture medium for 24 h at $37^{\circ}C$ and 200 rpm. Cytotoxicity of the extract was tested using NIH/3T3 mouse embryo fibroblast as a model cell. Growth inhibition was not observed in the extracts of HA membranes with the mole ratios of lactide to HA, 5 or 10, and 10% EDC concentration, however 11% of growth inhibition was observed in the extract with the mole ratio of 13. Growth inhibition was not observed in the extracts of HA membranes prepared with 5% EDC or 10% EDC and the mole ratio of lactide to HA, 10, however 12% of growth inhibition was observed in the extract with 20% EDC. Cytotoxicity was not observed in the extracts of HA membranes prepared at varying crosslinking temperatures, $15^{\circ}C,\;25^{\circ}C,\;and\;28^{\circ}C$ with the mole ratio of lactide to HA, 10 and 10% EDC.

• Korean Journal of Microbiology
• /
• v.36 no.4
• /
• pp.279-284
• /
• 2000

Simultaneous reduction of Cr(VI) and degradation of phenol was observed in batch and bench-scale continuous stirred tank reactors using Rhodococcus sp. CP01 isolated from leachate. The strain CP01, which was capable of utilizing phenol as a sole source of carbon and energy, completely reduced added hexavalent chromium (0.25 mM) to its trivalent form during 60 hr batch assay under optimal conditions (pH 7.0 and 1,000 mg/L of phenol concentration). The rates of Cr(VI) reduction and phenol degradation were estimated as 4.17 $\mu$M Cr(VI) and 38.4 mg phenol.$L^{-1}{\cdot}hr^{-1}$, respectively. The continuous culture experiment was conducted for 46 days using synthetic feed containing different levels of chromate (0.0625 to 0.25 mM) and phenol(1,000 to 4,000 mg/L). With a hydraulic retention time of 100 hr, Cr(VI) reduction efficiency was mostly 100% for influent Cr(VI) and phenol concentrations of 0.125 mM and 3,000 mg/L, respectively. During quasi-steady-state operation, specific rate of Cr(VI) reduction was calculated as 0.34 mg Cr(VI).g $protein^{-1}{\cdot}hr^{-1}$ which was comparable to reported values obtained by using glucose as growth substrate. The results suggest the potential application of biological treatment for detoxification of wastewater contaminated simultaneously with Cr(VI) and pheonol.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.34 no.4
• /
• pp.544-548
• /
• 2005

The objective of this study was to determine the effect of die temperature and dimension on extraction pattern, extract yield, and crude saponin content of extruded white ginseng. The extrusion variables were die temperature $(110\;and\;120^{\circ}C)$ and die dimension (3 holes with 1.0 mm, 2 holes with 2.0 mm, and 1 hole with 3.0 mm diameter). The browness and redness were indicator of active components in ginseng extract. Both were used to evaluate the effect of die temperature and die dimension on release pattern and release rate constant. Browness and redness of extract achieved its lowest value at die temperature $110^{\circ}C$ and 2 holes with 2.0 mm diameter, indicating the lowest extraction rate constant. Extract yield highly increased by extrusion treatment. Extract yield and crude saponin content were the highest at die temperature $120^{\circ}C$ and 1 hole with 3.0 mm diameter. In conclusion, extrusion process has contributed significantly in improvement of release rate of its active components.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.127-127
• /
• 2017

우리나라 음식물 폐기물은 수분함량 및 유기물 함량이 높기 때문에 부패와 악취, 침출수의 원인이 된다. 하지만 이를 혐기 소화 처리한다면 구성성분에 따라 60-80%가 생분해되어(한국유기성폐자원학회, 2001) 친환경적으로 처리가능하고, 혐기소화 결과물로 발생한 메탄가스를 대체에너지로 사용할 수 있어 유기물을 효과적으로 처리할 수 있다. 그러나 유기성 폐기물은 계절 및 지역에 따라 구성성분의 비가 다르며, 성분 중 지방 함량이 많을 때 바이오가스 생산이 지연되어 생산효율 감소의 주된 원인이 된다(Kafle and Kim, 2013). 전국음식물 폐기물 중 지방함량이 높은 어육류의 발생량은 3차 조사(환경부, 2008)에 비해 2배 이상 증가하였고, 향후 음식 섭취의 서구화로 인한 육류 소비가 증가할 것으로 예상된다(환경부, 2013). 따라서 본 연구는 지방함량이 높은 유기물의 효율적 처리를 위해 지방산 종류에 따라 포화 불포화 지방산을 포함하는 부산물의 혐기소화 능력 및 바이오가스 생산 성능을 구명하는데 목적이 있다. 본 연구 결과, 불포화 지방산 함량이 높은 수준인 부산물의 바이오가스는 629.96-749.14 mL/g VS 이며, 포화 지방산 함량이 높은 수준의 부산물은 560.18-715.43 mL/g VS 였다. 불포화 지방산 함량이 25.31%-46.26%로 많아질수록 초기 순응기간은 13일에서 25일로 증가하였고, 총 바이오가스 생산량의 90%가 생산되는 기간인 T90은 57일에서 72일로 증가하여 바이오가스 생산 속도가 감소한 것으로 판단된다. 포화 지방산은 함량이 24.10-48.74%로 증가할수록 초기 순응기간의 변화는 없었고, T90은 69일에서 62일로 감소하였다. 또한 불포화 지방산이 많은 유기물은 모두 바이오가스 생산 과정에서 2단계의 지연현상을 보였지만, 포화지방산은 함량이 증가하여도 1단계의 지연현상을 보였다. 이러한 차이는 두 지방산에 관여하는 미생물의 차이(Diana, 2007)와 불포화 지방산의 굴곡된 형태가 지방산과 미생물이 상호 작용 방식에 악영향 미치기 때문으로 판단된다(Diana, 2013). 결론적으로, 두 지방산의 소화 방식은 차이가 있으며, 불포화 지방산 함량이 많은 유기물은 탄수화물 함량이 많은 유기물을 10% 이상 혼합하여 지연상을 감소시킬수 있다(Kim, 2017). 포화 지방산 함량이 많은 유기물은 초기 지연 현상 해결을 위한 연구가 추가적으로 요구된다.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.14 no.1
• /
• pp.139-150
• /
• 2006

Landfilling is one of the most widely used methods for the final disposal of solid wastes. Landfilled wastes are degraded by residing microorganisms and the microbial degradation is affected by many factors such as moisture, oxygen, pH, alkalinity, sulphate, nutrient, temperature, and so on. Especially among these factor, oxygen and moisture within aerobic landfill play a major role in microbial degradation. In this study, 1) the effects of oxygen on the velocity of waste degradation and 2) the effect of moisture on the degradation of municipal solids waste (MSW) in aerobic condition were investigated. It was found that the BOD and CODcr concentration from the leachate of aerobic lysimeters dropped faster by 80 days after the start of the test compared to those from the anaerobic lysimeters. To see the effect of moisture, four aerobic lysimeters filled with MSW and four different levels of moisture (20, 30, 40, and 50%) were installed. From this test, higher moisture in MSW produced higher $CO_2$ concentration, meaning moisture was effective for the microbial degradation. thus, we concluded that higher moisture level in the aerobic landfill might help early-stabilization microbial degradation.

• The Journal of Engineering Geology
• /
• v.24 no.4
• /
• pp.525-534
• /
• 2014

Environmental problems typically occurring in abandoned mine lands (AML) include: contaminated and acidic surface water and groundwater; stockpiled waste rock and mill tailings; and ground subsidences due to mining operations. This study examines the effectiveness of various geophysical techniques for mapping potential hazard and contaminated zones. Four AML sites with sedimentation contamination problems, acid mine drainage (AMD) channels, ground subsidence, manmade liner leakage, and buried mine tailings, were selected to examine the applicability of various geophysical methods to the identification of the different types of mine hazards. Geophysical results were correlated to borehole data (core samples, well logs, tomographic profiles, etc.) and water sample data (pH, electrical conductivity (EC), and heavy metal contents). Zones of low electrical resistivity (ER) corresponded to areas contaminated by heavy metals, especially contamination by Cu, Pb, and Zn. The main pathways of AMD leachate were successfully mapped using ER methods (low anomaly peaks), self-potential (SP) curves (negative peaks), and ground penetrating radar (GPR) at shallow penetration depths. Mine cavities were well located based on composite interpretations of ER, seismic tomography, and well-log records; mine cavity locations were also observed in drill core data and using borehole image processing systems (BIPS). Damaged zones in buried manmade liners (used to block descending leachate) were precisely detected by ER mapping, and buried rock waste and tailings piles were characterized by low-velocity zones in seismic refraction data and high-resistivity zones in the ER data.

• Resources Recycling
• /
• v.13 no.5
• /
• pp.37-44
• /
• 2004

In this study, neodymium oxalate powders were prepared by injecting oxalic acid to the neodymium chloride solution resulted from the acid leaching solution of NdFeB magnet scrap. The effect of experimental conditions on the characteristics of neodymium oxalate powders were investigated. Neodymium oxalate was aggregated by primary particles formed by nucleation, and average size of aggregates was affected by experimental conditions. In a constant volume, increase of reactants affected the average size of aggregate formed by collision of primary particles. In a constant concentration of reactants, agitation speed decreased the size of aggregate due to breakage of particles attached on the surface of aggregate. The number of primary particles decreased with increasing reaction temperature, and the size of aggregates decreased due to the decrease of collision probability. From the results of decomposition behavior of neodymium oxalate, oxalate decomposed from $400^{\circ}C$, and neodymium oxide began to crystallize at above $620^{\circ}C$.

• Resources Recycling
• /
• v.26 no.4
• /
• pp.88-94
• /
• 2017

The recovery of gold in cyclone type electrolytic cell was conducted from solution for stripping gold of PCB by cyanide. The electrolytic recovery behaviors of gold was investigated by reaction time and addition of electrolytic sodium hypochlorite (NaOCl) and gold plating additive (KG-120). Because the electrolysis generated NaOCl reacted with the cyanide in the leachate by alkaline chlorination, more than 99% of the cyanide was removed at a $NaOCl(g)/CN^-(g)$ ratio of 1.0. When NaOCl was added during the recovery of the gold from cyanide leachate in the cyclone electrolytic cell, the recovery of gold was 98% at the ratio of $NaOCl(g)/CN^-(g)$ from 0.5 to 2.5 in 480 minutes and decreased rapidly over the ratio of 3.0. Gold was recovered more than 99% by adding 1.5 and 4.5%(v/v) of KG-120 with NaOCl in 480 minutes. In particular, when the concentration of KG-120 was 3.5 and 4.5%(v/v), more than 96% of gold was recovered within 240 minutes and the initial recovery rate was relatively faster. The optimum concentration of KG-120 is 3.5%(v/v) considering the economic feasibility and efficiency.