• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1097-1103
• /
• 2001

TiO$_2$anchored on a porous clay ceramic support (PCS) for use in lightweight photocatalyst were synthesized by the dropping precipitant method. A PCS of macro and micro pore size of around several mm~${\mu}{\textrm}{m}$ in diameter were prepared by the rapid heat treatment at, 1,15$0^{\circ}C$ for 10 min from low grade of clay. The change in pH of reaction solution due to the different addition rate of NH$_4$HCO$_3$as a precipitant, the reaction temperature and the concentration of TiCl$_4$had a pronounced effect on the nature of precipitated TiO$_2$particles on the surface of a PCS and the crystal structure of precipitated TiO$_2$particles. At an addition rate of 0.8 ml/min of NH$_4$HCO$_3$and pH=6 of reaction solution, homogeneous precipitation of TiO$_2$particles on a PCS was achieved. TiO$_2$particles with anatase phase was precipitated on the surface of a PCS at the low concentration of TiCl$_4$, the high addition rate of NH$_4$HCO$_3$and the high reaction temperature.

• Journal of Korean Society of Environmental Engineers
• /
• v.35 no.3
• /
• pp.171-178
• /
• 2013

In this study, the sludge that occurs in the initial operation of coagulation system developed for the treatment of CSOs were returned to the flocculation reactor. The purposes of this study were to analyze the Characteristics of flocs that are generated through the recycling sludge and settling characteristics of sludge, and to evaluate the possibility that high concentrations of particulate matter in the initial inflow of CSOs could be used as an weighted coagulant additive. As a result, the concentration of treated CSOs pollutants at the beginning of the CSOs influent with a large amount of particulate matter over 20 ${\mu}m$ was low, after gradually increasing the concentrations of them. The flocs generated from the sludge return were similar in size compared to flocs generated through injection of micro sands, and settling velocity in case of return sludge injection was decreased from 55.1 cm/min to 21.5 cm/min. SVI value of the sludge accumulated at the bottom of the sedimentation tank was 72, and settled sludge volume decreased rapidly due to the consolidation of sludge to the time it takes to 10 minutes. these mean that sludge used for recycling has good settling characteristic. A condition of returned sludge which is 0.1% return of 0.3% extraction was formed in the balance of settlement and extraction. In this case, This condition was to be adequate to maintain the proper concentration such as 100~200 mg/L of TS and 50~100 mg/L of VS in the flocculation reactor. The usage of the return sludge containing particulate matters of CSOs as an weighted coagulant additive was able to secure a stable treated water quality despite the change of influent water quality dynamically. Furthermore, it can be expected to reduce the alum dosage along with the sludge production.

• Journal of the Korean Ceramic Society
• /
• v.39 no.6
• /
• pp.550-557
• /
• 2002

TiO$_2$ particles coated on fly ash composites for use in photocatalyst were synthesized by the precipitation dropping method and heated at $700^{\circ}C$ for 2 h. The pH of reaction solution, the addition rate of NH$_4$HCO$_3$, the stirring speed, the reaction temperature and the concentration of TiC1$_4$ had a pronounced effect on the nature of precipitated TiO$_2$ particles on the surface off fly ash and the crystal structure of precipitated TiO$_2$ particles. At an addition rate of NH$_4$HCO$_3$; 1.0 ml/min, the pH of the reaction solution; 6, the stirring speed; 1,000 rpm and the reaction temperature; 8$0^{\circ}C$, about 10 nm of TiO$_2$ particle size and homogeneous precipitated layer on the surface of a fly ash was achieved. On the contrary, at an addition rate of NH$_4$HCO$_3$; 0.3,0.5 ml/min, the pH of the reaction solution; 2 and 11, the stirring speed; 300~500 rpm and the reaction temperature; lower than 5$0^{\circ}C$:, Inhomogeneous precipitated layer was developed on a fly ash. TiO$_2$ particles with anatase phase was formed as-dried precipitation at the low concentration of Tic14, the high addition rate of NH$_4$HCO$_3$ and the high reaction temperature, the crystalline fraction of anatase increased with raising heat-treatment temperature and rutile phase began to formation at 80$0^{\circ}C$. The crystal size of TiO$_2$ particles increased with raising the heat-treatment temperature, the crystal size was showed about 21 m at $700^{\circ}C$. Anatase type of TiO$_2$ coated on the fly ash heated at $700^{\circ}C$ for 2 h showed 1.25 g/cm$^3$of particle density, 82.8% of strength and 69.5 Lab of whiteness and can be used as a photocatalyst.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.8 no.1
• /
• pp.65-70
• /
• 2010

The distillation rate on LiCl-KCl eutectic salt under different vacuums from 0.5-50 mmHg was first investigated by using both a non-isothermal and a isothermal thermogravimetric (TG) analysis. Based on the non-isothermal TG data, distillation rate equations as a function of the temperature could be derived. Calculated flux by these model flux equations was in agreement with the distillation rate obtained from isothermal TG analysis. A distillation rate of $10^{-4}-10^{-5}$ mole $cm^{-2}sec^{-1}$ is obtainable at temperatures less than 1300K and vacuums of 0.5-50 mmHg. About a 99% salt distillation efficiency was obtained after an hour at a temperature above 1150 K under 50 mmHg in a small scale distillation test system. An increase in the vaporizing surface area is relatively effective for removing residual salt in the remaining particles, when compared to that for the vaporizing time. Over 99.95% of total distillation efficiency was obtained for a 1-h distillation operation by increasing the inner surface area from $4.52cm^2$ to $12.56cm^2$.

• Resources Recycling
• /
• v.30 no.4
• /
• pp.11-19
• /
• 2021

Arsenic (As) oxidation followed by precipitation from a high-As(III)-containing leaching solution derived from a sulfidic ore was investigated in this study to remove aqueous As from the solution using activated carbon (AC) with air injection as an oxidant. To obtain the initial leaching solution, a domestic sulfidic ore was leached in a sulfuric acid solution at pH 1 and 50℃ for 95 h, and approximately 7 g/L of Fe and 3 g/L of As were leached out. To determine the effect of the oxidative reaction utilizing AC with air injection, the leaching solution was tested under the following five oxidative conditions at an initial pH of 1 and 90℃ for 72 h: air-only injection; air injection with 1, 5, and 10 w/v% of AC addition; and H₂O₂ addition. The tests in the presence of both air and AC revealed that the oxidation kinetics and As removal were improved by the reaction between the metallic species and the surface group formed on the AC surface. In addition, the greater the amount of AC added, the better was the reaction efficiency, removing 93-94% of As with more than 5 w/v% of AC addition. Finally, X-ray diffraction analysis confirmed that the precipitate formed from the oxidative reaction was scorodite (FeAsO₄·2H₂O).

• Resources Recycling
• /
• v.31 no.2
• /
• pp.40-48
• /
• 2022

In this study, the effects of solution components were investigated in the recovery of vanadium as ammonium metavanadate from vanadium-ore-salt roasting-water leaching solution. The vanadium-containing solution is strongly alkaline (pH 13), so the pH must be lowered to 9 or less to increase the ammonium metavanadate precipitation efficiency. However, in the process of adjusting the solution pH using sulfuric acid, aluminum ions are co-precipitated, which must be removed first. In this study, aluminum was precipitated in the form of an aluminum-silicate compound using sodium silicate, and the conditions for minimizing vanadium loss in this process were investigated. After aluminum removal, the silicate was precipitated and removed by adjusting the solution pH to 9 or less using sulfuric acid. In this process, the concentration and addition rate of sulfuric acid have a significant influence on the loss of vanadium, and vanadium loss was minimized as much as possible by slowly adding dilute sulfuric acid. Ammonium metavanadate was precipitated using three equivalents of ammonium chloride at room temperature from the aluminum-free, aqueous solution of vanadium following the pH adjustment process. The recovery yield of vanadium in the form of ammonium metavanadate exceeded 81%. After washing the product, vanadium pentoxide with 98.6% purity was obtained following heat treatment at 550 ℃ for 2 hours.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2006.05a
• /
• pp.1093-1097
• /
• 2006

하천수계는 여러 인자들의 상호작용을 통하여 변화하게 되며, 하천 자정능력에 관한 연구는 이를 중심으로 진행되어 왔다. 여러 환경 요인 중 하상재료는 하천의 조도와 수생태계의 특성을 변화시키게 되며, 유입수의 성상에 따라 수저퇴적물이 쌓이거나, 생물막이 형성되는 매개체 역할을 하게 된다. 특히, 하천의 폭이 좁고 수심이 얕은 개울에서는 하상 퇴적물이 수질에 기여하는 영향이 큰 것으로 알려져 있다. 국내하천의 경우 하상재료가 주로 모래와 자갈이 주를 이루고 있으며, 수심이 낮아 빛의 투과성이 양호하여 부착조류의 증식 및 하상재료(모래 및 자갈 등)를 기질로 한 생물막 형성 등 하상재료는 하천환경의 변화 및 수질변화가 일어나는데 상당한 기여를 하는 것으로 보고되고 있다. 본 연구에서는 하천의 하상재료가 설치된 수로를 이용하여 이화학적요소를 조사, 분석함으로써 하상재료를 통한 수질변화 특성을 비교.검토 하였다. 그 결과 하상재료의 입경이 클수록 DO 변화가 더 큰 폭으로 증가 하였으며, 수위와 유속의 경우 수위가 낮으면서 유속이 적정수준일 경우 DO 증가가 나타나는 것으로 관측되었다. 하천수가 수로에 의해 순환되면서 유기물 저감속도의 측정결과 초기 흡착, 침전 등의 물리적 작용이 부착조류 증식 등의 생물학적 작용보다 우선되면서 입자성 유기탄소(POC)의 제거속도가 용존성 유기탄소(DOC) 의 경우보다 더 빠르고 우선되는 것으로 조사되었다. 영양염류의 경우 부착성조류에 의한 질소 제거능은 실제 질산화작용은 활발히 이루어졌으나 탈질작용에 의한 총질소의 제거는 미비한 것으로 나타났으며, 총인은 입자성유기탄소가 제거되는 것과 유사한 경향을 나타내 제거 기작이 대부분 흡착, 침전에 의한 물리적 자정 작용에 기인한 것으로 조사되었다. 또한 하상재료 입경 변화에 따른 수질변화 특성은 기질(하상재료)의 입경이 작을수록 오염물질의 분해능이 큰 것으로 나타났다. 이와 같이 여러 하천환경 요인 중 하상재료에 의한 하천환경의 다양한 변화는 수질변화 및 자정능력에 큰 영향을 미치게 된다.

• Journal of the Korean Geotechnical Society
• /
• v.36 no.1
• /
• pp.17-28
• /
• 2020

This study presents the experimental results of ground improvement efficiency induced by enzyme-induced carbonate precipitation (EICP) in soils. First, the optimal mixture ratio of EICP solution was determined by comparing the amount of induced carbonate depending on the different ratio among urea, CaCl₂, and urease. Next, we evaluated the shear stiffness and strength of EICP-treated sandy soil by performing shear wave velocity measurement and triaxial shear test. Furthermore, induced carbonate in treated soil was visually investigated by X-ray CT and SEM analysis. The results showed that the maximum shear stiffness evolved 19~30 times after 6 hours of reaction time compared with non-treated sands. Also, the cohesion and the friction angle tended to increase and decrease, respectively, as the amount of induced carbonate increased.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.3
• /
• pp.398-405
• /
• 2016

The cellulose nanofibers (CNFs) were prepared by wet disk-milling (WDM) and fractionated by settling method into supernatant, middle and sediment fractions. The diameter and its distribution of the fractionated CNFs were investigated. With increasing WDM passing number, precipitation became delayed. Weight fraction at sediment fraction was decreased, whereas those at supernatant and middle fractions were increased with increasing WDM passing number. Diameter distribution of CNFs at supernatant fraction was narrowest and became broaden at middle and sediment fraction. Filtration time was longer in order of supernatant, middle and sediment fraction.

• Korean Chemical Engineering Research
• /
• v.56 no.3
• /
• pp.349-355
• /
• 2018

$BaMnAl_{11}O_{19}$ was prepared by urea-induced homogeneous precipitation and characterized by X-ray diffraction and scanning electron microscopy. At increased precipitant concentrations, AlOOH replaced $Al(OH)_3$ as an Al precursor. $BaMnAl_{11}O_{19}$ exhibited enhanced catalytic combustion performance and inhibited CO generation. Catalytic performance was also enhanced by the presence of $BaAl_2O_4$ and $BaMnAl_{11}O_{19}$. Compared to $BaAl_2O_4$, $BaMnAl_{11}O_{19}$ exhibited superior catalytic combustion activity.