• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.250-255
• /
• 2011

In this study, by using the polymeric membrane separation process, the $CO_{2}/CH_{4}$ separation and $H_{2}S$ removal from biogas were performed in order to $CH_{4}$ purification and enrichment for the fuel cell energy source application. Fibers were spun by dry/wet phase inversion method. The module was manufactured by fabricating fibers after surface coating with silicone elastomer. The scanning electron microscopy(SEM) studies showed that the produced fibers typically had an asymmetric structure; a dense top layer supported by a porous, sponge substructure. The permeance of $CO_{2}$ and $CO_{2}/CH_{4}$ selectivity increased with pressure and temperature. Mixture gas with increasing pressure and temperature, removal efficiency of the $CO_{2}$ and $H_{2}S$ were decreased while concentration of $CH_{4}$ was increased up to 100%. When retentate flow rate was increased with the decreasing of pressure and temperature the $CH_{4}$ recovery ratio in retentate side was increased while the $CH_{4}$ purity in retentate side was decreased.

• Journal of the Korean Electrochemical Society
• /
• v.2 no.3
• /
• pp.150-155
• /
• 1999

The Electrochemical stabilities of the Brewer-Engel type intermetallic compounds of Co-Mo $(35 wt\%)$ and Ni-Mo$(35 wt\%)$ manufactured by the arc-melting method for the hydrogen electrode of $H_2-O_2$ alkaline fuel cell were investigated. Effects of temperature and concentration on the electrochemical behavior of the electrodes in the $80^{\circ}C$ 6 N KOH solution deaerated with $N_2$ gas were studied by electrochemical methods. The effect of overpotential on the electrochemical stabilities of Co-Mo and Ni-Mo intermetallic compounds was also discussed under the normal operation condition of AFC. It was shown that Co-Mo electrode had lower electrochemical stability as compared to Ni-Mo. In the case of Co-Mo electrode, a simultaneous dissolution of cobalt and molybdenum has occurred at low anodic overpotential form equilibrium hydrogen electrode potential, but the dissolution of cobalt was serious, and Co(OH)l layer on the electrode surface formed at the high anodic overpotential. In contrast the Ni-Mo electrode had high electrochemical stability because formation of the dense and thin protective $Ni(OH)_2$ layer prevented the dissolution of molybdenum.

• Journal of the Korean Ceramic Society
• /
• v.36 no.1
• /
• pp.43-49
• /
• 1999

Gas pressure sintered silicon nitride based composites with 0~5wt% $\beta$-Si3N4 whiskers were prepared. The whiskers were unidirectionally oriented by a modified tape casting technqiue and green bodies with various microstructure were formed by changing stacking sequences of sheets cut from the tape. Orientations of the large elongated grains of the sample after gas pressure sintering were the same as the those of the whiskers of green body, and the sintering shrinkage and mechanical properties of sintered sample were consistent with the microstructural characteristics. In case of unidirectional samples, the sintering shrinkage normal to whisker alignment direction was larger than that parallel to the direction. The shrinkage difference inceaed as the whiskercontent increaed. As whisker content increaed, the crack length normal to and parallel to tape casting direction became shorter and larger, respectively. Although the grain size increased by th whisker addition, the flexural strength of unidirectional samples was not lower than that of smaple without the whisker. In case of crossplied and 45$^{\circ}$rotated samples, the anisotropy of mechanical preoperties disappeared.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.786-789
• /
• 2011

In order to estimate the possibility of applying electrolytes generally used in solid oxide fuel cells(SOFCs) to direct carbon fuel cells(DCFCs), properties of YSZ(yttria stabilized zirconia) electrolyte were evaluated. In this study, vacuum slurry coating method was adapted to coat thin layer on anode support substrate. After sintering the electrolyte at $1400^{\circ}C$ for 5hrs, microstructure was analyzed by using SEM image. Also, gas permeability and ionic conductivity were measured to find out the potential possibility of electrolyte for DCFCs. The YSZ electrolyte represented dense coating layer and low gas permeability value. The ionic conductivity of YSZ electrolyte was high over $800^{\circ}C$. After measurement of the electrolyte properties, direct carbon fuel cell was fabricated and its performance was measured at $800^{\circ}C$.

• Journal of the Korean Vacuum Society
• /
• v.18 no.2
• /
• pp.141-146
• /
• 2009

PLZT ferroelectric thin films were deposited on Pt/Ti/$SiO_2$/Si substrate with $TiO_2$ buffer layer in between by rf magnetron sputtering method. In order to investigate the effect of Ar/$O_2$ partial pressure ratio on the ferroelectric properties of PLZT thin films, PLZT thin films were deposited at various Ar/$O_2$ partial pressure ratio ; 27/1.5 seem, 23/5.5 seem, 21/7.5 seem and 19/9.5 seem. The crystallinities of PLZT thin films were analyzed by XRD. The surface morphology was observed using FE-SEM. The P-E hysteresis loops, the remanent polarization characteristics and the leakage current characteristics were obtained using a Precision LC. The crystallinity and elaborateness of PLZT thin films were decreased as increasing the oxygen partial pressure ratio. And preferred orientation of PLZT thin films changed from (110) plane to (111) plane. The oxygen partial pressure ratio affects the thin film surface morphology and the ferroelectric properties.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.4
• /
• pp.177-186
• /
• 2005

The latest concrete structure has showed that the deterioration of durability has been increased by the damage from salt, carbonization, freezing & thawing and the others. Therefore, the measures for the concrete which has deteriorated durability have been taken. Among them, it has been often used that surface treatment which cuts off the deterioration factors of durability by protecting the surface of concrete. However, troubles such as fracture and rupture in the repair layer have been reported as time goes by due to the difference between the organic repair material like epoxy and concrete properties. Researchers have been developing the repair material which can cut off the deterioration factors of durability such as $CO_2$ gas, chloride ion and water by making the formation of concrete elaborate through the reaction with calcium ion when the surface improving agent is coated on the concrete. The main ingredient of that is inorganic substance which is the same as the concrete property. This study was evaluated the surface improving agent for permeability, watertightness, air-permeability, chemical resistance and elution resistance. As a result, it has been reported that the surface improving agent improves watertightness and air-permeability by penetration more than 10mm within concrete. Therefore, it is concluded that the surface improving agent developed in this research prevents deterioration of concrete durability when it is coated on the concrete structure.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.198-198
• /
• 2015

전기변색재료는 전압을 인가하였을 때 전계방향에 따라 가역적으로 색이 변화하는 재료를 말한다. 스마트윈도우용 전기 변색재료는 지속적으로 전기를 가해줄 필요 없이 한번 변색되면 색이 지속되는 특징을 가지므로 에너지 효율적으로 우수하여 태양열 차단 창호나 디스플레이 분야에 응용될 것으로 기대된다. 이러한 전기 변색재료에는 산화형 전기 변색 재료, 환원형 전기 변색 재료가 있는데 이중 가장 널리 연구되고 있는 재료는 환원형 전기변색재료이다. 대표적인 재료로 $WO_3$가 쓰이는 데 이는 전기 변색적 특성이 우수하고 또한 내구성이 다른 재료에 비해 우수하다는 장점 때문이다. 그러나, 상용화를 위해서는 내구성의 개선이 요구되고 있다. 한편, $TiO_2$는 안정성이 매우 뛰어나지만 전기변색적 특성이 $WO_3$에 비해 낮은 점이 지적되고 있다. 이러한 $WO_3$ 및 $TiO_2$ 박막은 스퍼터링 또는 sol-gel법 등으로 제작되고 있는데, 일반적으로 스퍼터링의 경우 치밀한 박막이 형성되기 때문에 Porous 한 박막을 얻기 힘들다. 따라서 본 연구에서는 기판에 입사하는 스퍼터 입자들의 각도를 조절하여 shadowing 효과로 인해 박막의 구조가 porous해지는 Glancing angle deposition을 도입하였다. 이러한 증착법을 이용하여 $WO_3$와 $TiO_2$를 각도를 조절하여 증착하고 $TiO_2$와 $WO_3$ 박막의 특성을 비교하여 본다. 두께 300 nm를 가지는 $WO_3$ 및 $TiO_2$ 박막은 GLAD RF 마그네트론 스퍼터링법을 이용하여 Corning glass(corning E-2000)기판 위에 증착하였다. 기판 입사 각도는 $0^{\circ}$, $30^{\circ}$, $45^{\circ}$, $60^{\circ}$로 증착하였고 직경 3 in의 $TiO_2$, $WO_3$ 타겟을 사용하였다. 또한 스퍼터링 파워는 400 W, 작업압력 1.0 Pa, 그리고 스퍼터링 가스는 O2/Ar+O2 유량 10%에서 30%로 증착을 상온에서 진행하였다. 전기화학적 특성을 평가하기 위하여 $TiO_2$ 및 $WO_3$ 박막을 100 nm 두께의 ITO/glass 위에서 증착하였다. 박막의 미세구조는 XRD와 SEM을 통해 확인하였고, 전기화학적 특성은 Ar 분위기의 Glove box안에서 parstat 2273을 통해 측정하였다. 전해질은 1 M $LiPF_6/PC$로 진행하였고, 대향 전극는 Pt전극을, 참고 전극은 칼로멜 전극을 사용하였다. Potential 범위는 2 V에서 4 V로 진행하였고, scan rate는 50 mV/s로 측정하였다. 투과도는 UV/VIS spectrometer로 측정하였다. 전기변색 특성의 상관관계 및 에 대해서는 학회 당일 발표할 예정이다.

• The Journal of the Petrological Society of Korea
• /
• v.13 no.3
• /
• pp.161-177
• /
• 2004

The Cretaceous pink granites of the finan area, southwestern Ogcheon belt, are adjacently developed in the eastern part (Keg) and western part (Kwg) as stocks, respectively. Keg of rounded shape occur as mainly medium-coarse grained rocks, whereas Kwg of ellipsoidal shape occurs as medium-coarse grained ones with partly porphyritic and fine-grained textures. Miarolitic cavities of them are often seen and can be observed more frequently in Kwg than Keg. Rose and counter fracture diagrams of the two granites show that Keg and Kwg have more potentiality of non-dimension and dimension to non-dimension stones, respectively. Physical properties such as porosity and absorption ratio have 0.25% and 0.65％, and 0.43% and 1.11%, respectively, which could suggest that emissions of gas phase at later magma stages are abundant in Kwg than those of Keg. From the major and trace elements petrochemisoy, they belong to acidic, peraluminous and calc-alkaline rocks, showing that Kwg are later product than Keg of the same granitic parent magma. REE concentrations normalized to chondrite value have trends of gradual and parallel enriched LREE and depleted HREE. Eu negative anomalies of Kwg are far more severe than those of Keg, which suggest that plagioclase fractionation in Kwg was much stronger than that of Keg. In the magnetic susceptibility vs. petrochemical and modal parameters, they all belong to magnetite-series and I-types, and can be classified as weakly-moderately ferromagnetic rocks. And the above relations could suggest that their susceptibility values are more mainly depended on ferromagnetic opaques than ferromagnetic and paramagnetic assemblages (Bt ＋ Ch ＋ Ser ＋ Op).

• Journal of Conservation Science
• /
• v.32 no.2
• /
• pp.123-139
• /
• 2016

The excavated potteries of Goryeo Period from the Sandongri archaeological site in Seosan were studied on physicochemical analyses. Surface color of the samples are mainly grayish blue, and showed the natural glaze by melting the body soils during the burning. Partly, swelling surface are observed bloated marks because of blow out gas by burning. The potteries are some possibility of making the similar source clay on the basis of magnetic susceptibilities (about $1{\times}10^{-3}SI\;unit$) and general occurrences. Values of specific gravity, apparent porosity and absorption ratio are divided two groups as highly different cases of bloating surface samples. The source clay of the potteries used mainly microcrystalline clay, the mineral compositions are quartz and some colored minerals. Based on the analysis, the burning temperature of the potteries are assumed that they were around $1,100^{\circ}C$ because detection of quartz and mullite within hard and compact matrices. As geochemical variations of the samples, evolution trends of rare earth, compatible and incompatible elements showed very similar patterns excepting the some major elements, that means the potteries are interpreted to making by elutriation processes using the same raw clays from very similar basement rocks of genetically.

• Journal of the Korean Applied Science and Technology
• /
• v.24 no.2
• /
• pp.174-181
• /
• 2007

In this study, $SiO_2/poly(ethylene-co-vinyl$ alcohol)(EVOH) hybrid coating materials with gas barrier property could be produced using sol-gel method. The biaxially oriented polypropylene (BOPP) substrate with surface pretreatment was coated with the prepared hybrid sols containing various inorganic silicate component by a spin coating method. Crystallization behavior of the hybrids was investigated in terms of analysis of X-ray diffraction and cooling thermogram from DSC experiment. From the morphological observation of the $SiO_2/EVOH$ hybrid gel, it was confirmed that there existed an optimum content of inorganic silicate precursor, Tetraethylorthosilicate (TEOS), to produce hybrid materials with dense microstructure, exhibiting uniformly dispersed silica particles with average size below 100 nm. When TEOS was added at below or above the optimum content, particle clusters with large domain were observed, resulting in phase separation. This morphological result was found to be in good agreement with that of oxygen permeability of the hybrid coated films. In the case of film coated with hybrid prepared from addition of 0.01 - 0.02mol of TEOS, a remarkable improvement in barrier property could be obtained, however, with the addition of TEOS more than 0.04 mol, the barrier property was dramatically reduced because of phase separation and micro-crack formation on the film surface.