• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.426-426
• /
• 2022

하천에서 유사량은 침식(Erosion), 유송(Transport), 퇴적(Deposition)의 3단계 과정으로 진행되며 이 과정에서 다양한 유사 문제가 수반되고 있다. 특히, 하상변동의 예측, 하천계획 수립 등 수자원 개발을 위해 유사량 조사는 반드시 필요하다. 따라서 국외에서는 오래전부터 하천 유사이송과정에 대한 이론적인 개념을 정립하고 양질의 유사량 자료를 위해 연구해 오고 있다. 국내에서는 대표적으로 한국수자원조사기술원에서 유사량조사 업무를 수행하고 있으며 국가유사량관측망 중 매년 약 20개소~30개소의 지점을 대상으로 신뢰성 있는 자료를 만들기 위해 지속적으로 연구하고 있다. 유사량 조사의 항목 중 부유사 채취를 위한 측선수는 하천 폭(ISO 기준)에 따라 5개~7개의 측선에서 부유사를 채취하고 있으며, 강우가 활발한 홍수기 전, 후로 단면측량 및 하상토 자료를 통해 총유사량을 산정하고 있다. 본 연구의 분석방법으로는 이신재(2021)가 제안한 방법을 착안하였고, 측선별 부유사농도와 평균부유사농도의 비교분석 통해 상관계수(R²)가 가장 높은 측선을 선택하여 지표부유사량(Index Suspended Sediment) 산정에 활용하였다. 대상지점으로는 연속 유사량 자료 생산이 가능한 낙동강유역의 함안군(계내리) 관측소와 영산강유역의 구례군(구례교) 관측소를 선정하였다. 먼저, 지표 유사량은 평균부유사농도와 측선별 부유사농도를 비교분석하였으며, 함안군(계내리) 관측소는 5번 측선(R²=0.9869), 구례군(구례교) 관측소는 2번 측선(R²=0.9929)을 통해 지표부유사량을 산정하였다. 그 결과 하천특성에 따라 측정된 부유사량과 지표부유사량의 편차율(함안군(계내리) : 최대 33%, 최소 1%, 구례군(구례교) : 최대 25%, 최소 1%)이 다소 상이한 구간이 발생하였지만 이들의 상관계수(R²)는 각각 0.9922, 0.9947로 매우 높게 산정되었다. 이러한 결과를 통해 제시한 지표 설정은 실제 업무에서 활용 가능할 것으로 판단되며, 추후 과거년도의 하천특성과 수리특성 분석을 통해 해당지점의 대표적인 측선을 선정해 연속적인 지표 유사량 자료 생산이 가능하다면 향후 자동 유사량 채수장치 설치를 통해 안정된 유사량 자료 제공이 가능할 것으로 기대된다.

• Geophysics and Geophysical Exploration
• /
• v.1 no.2
• /
• pp.92-100
• /
• 1998

Array CSAMT surveys were conducted in two areas where it was not easy to identify the presence of faults only with geological survey because of thick overburden. The purpose of these surveys were to locate the faults and to delineate the deep resistivity structures around the faults. The steep dip lineaments having high contrast in resistivity laterally and the low resistive zones having some width in the resistivity sections were interpreted as faults and fracture zones associated with faults, respectively, The good applicability of array CSAMT to the investigation of fault was recognized owing to the agreement between the interpretation results of array CSAMT and the conclusive evidences collected by the following geological survey. The evidences includes the recent exposure of fault and the trajectory of fault evidences of the survey line. A comparison of the applicabilities of array CSAMT method and the resistivity method using dipole-dipole array was presented with the results of both methods along a same traverse line.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.16-16
• /
• 2021

전자파표면유속계(Microwave Water Surface Current Meter)를 이용한 홍수기 유량측정은 교량과 같은 구조물을 이용하여 안전 및 측정위치의 흐름조건 등의 이유로 측정의 한계가 발생한다. 이런 문제점을 개선하기 위해 전자파표면유속계를 드론(Drone)과 결합하여 하천에서의 유량측정에 이용하였다. 전자파표면유속계는 비접촉식 유속측정 장비로 하천의 표면유속을 측정하고 유량산정을 위해 환산계수 0.85를 적용하여 평균유속을 산정하고 있다. 환산계수 0.85는 하천의 각 횡측선 수심-유속분포를 일반적인 분포로 가정하고 표면유속에 0.85를 곱하여 평균유속을 산정한다(Rantz, 1982). 그러나 하천의 측정위치 및 흐름특성에 따라 유속분포가 변화하기 때문에 국외 많은 연구에서 환산계수의 범위를 0.72에서 1.72까지 제시한 바 있다(Johnson and Cowen, 2017). 따라서 환산계수 0.85의 일률적인 적용은 부정확한 유량산정을 초래할 수 있어 측정위치에 적절한 환산계수 산정이 필요하다. 본 연구에서는 2020년 금강의 지류인 봉황천에 위치한 금산군(황풍교) 관측소에서 드론과 전자파표면유속계를 이용해 측정한 표면유속과 ADCP를 이용하여 동시 측정한 평균유속의 비교를 통해 환산계수를 산정하여 평균유속 산정의 정확도를 높이고자 하였다. 전자파표면유속계로 측정한 6개 성과 중 ADCP와 동시 측정한 4개의 성과를 분석하여 환산계수를 산정하였다. 측정성과별 측선수는 16~17개로 홍수터로 월류하여 비정상흐름이 발생한 측선은 제외하고 측선별 환산계수는 0.66에서 1.09의 범위로 나타났고, 성과별 환산계수의 평균치는 0.90에서 0.93 범위로 산정되었다. 환산계수가 일반적인 수치보다 높게 산정된 것은 측정위치 하류 약 600m에 위치한 콘크리트 고정보의 영향이 홍수 시 흐름의 수위-유속분포에 영향을 미쳐 높게 산정된 것으로 판단된다. 따라서 유량산정에 있어 환산계수는 4개 성과에서 산정된 환산계수의 평균치인 0.92를 적용하여 산정하였다.

• Korean Journal of Ichthyology
• /
• v.22 no.3
• /
• pp.206-209
• /
• 2010

A specimen of Redigobius bikolanus (29.0 mm SL) belonging to the family Gobiidae was collected by a hand net from the estuary of Changgo-cheon (river) in Andeok-myeon, Jeju Island, Korea. This specimen was characterized by having 26 lateral line scales, 7 predorsal scales, 7 transverse scales, anterior oculoscapular canal, preopercular canal, and four black spots between origin of anal fin and lower origin of caudal fin. The morphological characteristics of the specimen well matched those of Redigobius bikolanus previously reported. Thus, we newly add this species to the list of Korean fish fauna and propose its new Korean name, "Jeom-bak-i-mang-duk".

• Journal of the Korean Geophysical Society
• /
• v.8 no.2
• /
• pp.81-87
• /
• 2005

Acquisition and processing of vector seismic waves were conducted through simultaneous generation of P, SH, and SV waves and receiving those waves using three-component geophones. Test data were received by 24 8-Hz geophones at an interval of 2 m along a 94-m profile. The data were recorded for 512 ms with sampling intervals of 0.2 ms. Raw data indicate that both reflected and refracted P waves are strongly recorded on the vertical component while SH waves are significant on the transverse horizontal component. On the inline horizontal component, both direct P and converted PS waves are recorded. First arrivals of P and SH waves were detected simultaneously on the vertical and transverse horizontal axes, respectively. The recorded vector data were separately inverted using traveltime tomography to yield P- and SH-wave sections. Using those two velocity sections, Poisson's ratios were able to be obtained effectively.

• Journal of the Korean Geotechnical Society
• /
• v.16 no.1
• /
• pp.145-155
• /
• 2000

Orientation data of discontinuities are of paramount importance for rock slope stability studies because they control the possibility of unstable conditions or excessive deformation. Most orientation data are collected by using linear sampling techniques, such as borehole fracture mapping and the detailed scanline method (outcrop mapping). However, these data, acquired by the above linear sampling techniques, are subjected to bias, owing to the orientation of the sampling line. Even though a weighting factor is applied to orientation data in order to reduce this bias, the bias will not be significantly reduced when certain sampling orientations are involved. That is, if the linear sampling orientation nearly parallels the discontinuity orientation, most discontinuities orientation data which are parallel to sampling line will be excluded from the survey result. This phenomenon can cause serious misinterpretation of discontinuity orientation data because critical information is omitted. In the case study, orientation data collected by using the borehole fracture mapping method (vertical scanline) were compared to those based on orientation data from the detailed scanline method (horizontal scanline). Differences in results for the two procedures revealed a concern that a representative orientation of discontinuities was not accomplished. Equal-area, polar stereo nets were used to determine the distribution of dip angles and to compare the data distribution fur the borehole method versus those for the scanline method.

• Economic and Environmental Geology
• /
• v.39 no.4 s.179
• /
• pp.417-426
• /
• 2006

Data acquisition is as important as data processing and interpretation in the field of marine geophysical exploration. Marine geophysicist, however, may not have enough information in this field because data acquisition method has been mainly developed by the commercial companies manufacturing the equipment. Therefore, the purpose of this paper is to introduce the general data acquisition method and information to help to construct the systematic and effective survey plan. When a survey plan is set up, the most important thing is to select the seismic equipment based on required penetration depth and resolution, and then construct the survey line intervals. Although a line interval varies from the research purposes, it should be narrower than the expected subsurface structures. Also, if 100% coverage of multibeam data is required, line intervals need to be adjusted based on the equipment characteristics. In case of merging with the preexisting dataset like bathymetry, gravity and magnetic, cross-over errors occurred at the each cross point should be removed to avoid any kinds of misinterpretation.

• The Korean Journal of Quaternary Research
• /
• v.16 no.1
• /
• pp.17-27
• /
• 2002

Analysis of No. 199∼145 cross-sections set up by the Ministry of Construction (1978) in the middle reaches of the Sumjin River around Sunchang, Daegang, and Goksung areas have been done for delineating the changes In fluvial geomorphic features. The entire river-bed in the study area has been considerably degraded since 1978. In some cross-sections, the thalweg shillings are observed. Two aspects are responsible for the erosion-dominant environment. First, flow velocity has been increased. Human activities including wetland destruction, ex-channel destruction and artificial levee construction reduced the channel width, and fixed the channel geometry. This has resulted in increase of the water velocity. Pebble and granule∼coarse sand are prevailing on the river-bed, indicate the high speed of the currents. Second, aggregate has been intensively mined during 1980s∼1990s around the areas. Especially, in the right side of the cross-sections No. 188∼187 and the left side of the cross-section No. 155, erosion toward under the artificial levee is remarkable. This can be led to bank failure in case of heavy rainfall.

• Proceedings of the KSEEG Conference
• /
• 1999.04a
• /
• pp.126-126
• /
• 1999

• Journal of Sericultural and Entomological Science
• /
• v.20 no.2
• /
• pp.15-19
• /
• 1978

In order to identify hormone activities which related to the changing of cutaneous tissue and pupal bodies and also to identify the interaction of corpora allata hormone and prothoracic glandular band hormone which act upon the metamorphosis of the insect. The item of treatment is carried out in 5 different times at the interval of about 12 hours after 4 weeks from the first feeding of 4th instar stage, and as far as 5th instar stage in concerned 6 times of item treatments have been carried out, at about 12 hours interval after 72 hours from the molting, Item treatments were, made in the stage of spring, autumn rearing, However, during the period of post mounting stage and pre pupation by picking out of corpora allata in 5 times at the interval of hours the following change of pupal colour is observed; 1) By an early pick out of 4th instar stage, the three molters are found in greater number, However, by a later pick out the four molters are found instead of others. 2) An abnormal colour is found in the three and four molters when comparing with the control molters. 3) The most of control molters have shown the normal colour except a few samples. 4) As shown in the table 1 and 2, the death number of item treatment is greater in the autumn rearing season. 5) The picking out of corpora allata of 5th instar stage, the post mounting stage and pre pupation period is affecting the change of colour. 6) As a final conclusion, the corpora allata hormone is closely related to the changing of pupal colour.