• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.91-96
• /
• 2014

Through silicon via (TSV) technology is to form a via hole in a silicon chip, and to stack the chips vertically for three-dimensional (3D) electronics packaging technology. This can reduce current path, power consumption and response time. In this study, Cu-filling substrate size was changed from Si-chip to a 4" wafer to investigate the behavior of Cu filling in wafer level. The electrolyte for Cu filling consisted of $CuSO_4$ $5H_2O$, $H_2SO_4$ and small amount of additives. The anode was Pt, and cathode was changed from $0.5{\times}0.5cm^2$ to 4" wafer. As experimental results, in the case of $5{\times}5cm^2$ Si chip, suitable distance of electrodes was 4cm having 100% filling ratio. The distance of 0~0.5 cm from current supplying location showed 100% filling ratio, and distance of 4.5~5 cm showed 95%. It was confirmed good TSV filling was achieved by plating for 2.5 hrs.

• Journal of the Korean Institute of Gas
• /
• v.22 no.6
• /
• pp.59-64
• /
• 2018

As part of measures to reduce fine dust, the government is promoting a project to convert the fuel of Yard Tractors(YT, tractors operated at ports), from diesel to LNG (Liquefied Natural Gas). While a port having a small number of yard tractors, it is not proper to construct a stationary LNG fueling station and supply LNG to YT due to a problem of BOG (Boil off gas) generation. Therefore, it is necessary to make a regulation and a standard on mobile LNG YT refueling station installation and inspection as an alternative. In this study, we have investigated domestic and foreign mobile LNG refueling cases and refueling standards, including the USA and Europe. In addition, we have suggested the risk reduction method according to the cause after investigation of the cause of LNG accidents. And last, based on the proposed risk reduction measures, we have proposed an amendment to the Regulation of the Urban Gas Business Law in Korea. The proposed mobile LNG YT refueling amendment of the Regulation includes ; maintenance of the safety distance from the protection facility, installation of an interlock device to prevent refueling in places other than the authorized place, installation of the identification system through biometrics, separation of the tank lorry and tow vehicle before refueling, checking the wheel fixed status of tank lorry before refueling, construction of the impounding area, safety measures before, during and after refueling, etc. The safety standards proposed in this study could be used as a reference in establishing standards for mobile LNG vehicle refueling in the near future.

• The Korean Journal of Mycology
• /
• v.20 no.1
• /
• pp.72-76
• /
• 1992

The extraction and separation methods of protein-bound polysaccharides from the mycelium and culture broth of Coriolus versicolor (Fr) Quel were investigated. The use of 2% solution of surface active agent Triton X-100, was effective for extraction of the protein-bound polysaccharides from the mycelium. For the separation and partial purification of the protein-bound polysaccharides, the column chromatography using DEAE-Cellulose and DEAE-Sephadex proved to be effective.

• Restorative Dentistry and Endodontics
• /
• v.29 no.1
• /
• pp.51-57
• /
• 2004

본 연구는 에폭시레진계 봉함제 (AH26)과 두 가지의 상아질 접착제와 함께 근관충전을 시 행하였을 때와 에폭시레진계 봉함제 단독으로 사용하였을 때의 미세누출을 혐기성 세균모델을 이용하여 평가하였다. 52개의 단근치를 이용하여 .04, .06 taper Profile (Dentsply-Maillefer, Ballaigues, Swiss)을 사용하여 변형된 crown-down pressureless법으로 근관형성 하였다. 형성된 치근을 12개씩 무작위로 나누어 4개의 실험군으로 하였으며, 나머지 치아 중 2개를 양성대조군에, 2개는 음성대조군으로 사용하였다. 제1군은 All Bond 2(Bisco, Itasca, IL, USA)를 적용하고 거타퍼쳐와 AH26 (Dentsply, Konstanz, Germany)을 이용하여 continuous wave of condensation technique으로 근관충전 하였으며, 제 2군은Prime ＆ Bond NT (Dentsply, Konstanz, Germany)를 적용 후 거타퍼쳐와 AH26을 이용하여 충전하였으며, 제3군은 17％ EDTA를 적용하여 도말층을 제거한 후 거터퍼쳐 와 AH26을 사용하여 충전하였다. 제4군은 17％ EDTA를 적용하지 않고 거터퍼쳐와 AH26을 사용하여 충전하였다. Fusobacterium nucleatum (VPI 10197)을 추적자로 이용한 혐기성세균모델을 사용하여 혐기성배양기에서 배양시키면서 60일 동안 각군에 대한 미세누출 여부를 관찰하였다. 매일 배양액의 혼탁도와 색상변화를 관찰하여 기록하였다. 제4군에서 통계학적으로 유의할만한 미세누출을 가장 많이 보였으며(p<0.0005) 나머지 3개의 실험군에서는 서로간의 통계학적으로 유의할 만한 차이를 보이지 않았다. 주사전자현미경 관찰 시 제 1군과 제2군의 상아질 접착제가 상아세관으로 침투한 소견을 관찰 할 수 있었다.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1995.05b
• /
• pp.921-927
• /
• 1995

수지충전식 전해재생조내에서 바나듐-철-Picolinate 착화물이 함유된 모의 LOMI 제염폐액의 재생거동에 대한 공정변수의 영향을 조사하였다. 전기투석에 의해 양이온종이 제염 폐액으로부터 제거되는 재생 분리효율에 대한 전류밀도, 제염폐액 공급유량 및 재생조내 수지층두께 등 공정변수의 영향은 바나듐이온이 가장 크게 받는다. 공정변수의 영향을 총괄 파라미터인 공정변수비 $\alpha$로 정의하여 나타낼 때 재생 분리효율 95%이상을 얻기 위해서는 $\alpha$가 0.2 이하로 유지되어야 한다. LOMI 제염폐액의 재생시 전기투석 flux는 공정변수비, $\alpha$값이 증가함에 따라 철이온이 바나듐이온에 비해 더욱 커지는 경향을 보였다. 재생종료 후 발생되는 음극폐액내 철 및 코발트 등 방사성이온종은 음극액의 초기 수소이온 농도를 조절하면 침전제의 첨가 얼이 음극반응에 의해 음극액의 pH를 산성에서 알카리성으로 바꿀 수 있어, 수산화물 형태의 침전물 입자로 만들어 쉽게 제거할 수 있다. 재생시 바나듐이온은 대부분 $V^{III}$(Pic)$_2$$^{+}$ 착화물형태로 전기투석된다. 음극액으로 formate용액을 사용하면 철 및 코발트 등 방사성이온종을 제거한 음극액은 농축된 LOMI제염제로 회수하여 필요시 산화가를 조정한 후 재생된 착화제와 혼합하여 제염제로 재사용할 수 있어, 더욱 효과적으로 제염폐액을 재생하는 향상된 재생방법이다.다.

• Korean Chemical Engineering Research
• /
• v.48 no.5
• /
• pp.668-671
• /
• 2010

A lab scale distillation experiment is conducted with small size packing used in lab scale multi-tray distillation equipment for the performance evaluation of distillation system. A sufficient surface are yielded with 6.7 mm cylindrical packings made of stainless steel, and a good liquid holdup and residence time are resulted. The comparison between the theoretical tray from the HYSYS and the experimental distillation outcome indicates that a 7 cm HETP from 27 cm packing height and a 8 cm HETP from 45 cm packing height are obtained. Comparing with the 8 cm HETP of commercial structured packing shows a similar experimental results obtained here. The 7 cm HETP is available with a complete insulation, and the importance of the insulation is proved. The results of this study indicates that a practical distillation column used in field can be tested in lab.

• Polymer(Korea)
• /
• v.34 no.5
• /
• pp.430-433
• /
• 2010

The gasket materials of for the lithium ion battery requires chemical resistance to electrolyte, electrical insulating, compression set, anti-contamination and low temperature property. To check the special characteristics of fillers which are applied to rubber for gasket, compound of EPDM, NBR and FKM (fluoro elastomer) were made by adjusting weights of carbon black and silica additive. Using these compounds, we had done tests of long-term stability against electrolyte, compression set and low-temperature property with considering operating condition of the lithium ion battery. From this test, we investigated the physical and chemical characteristics of rubber with using of carbon black and silica additive in each.

• Proceedings of the KIEE Conference
• /
• 2002.04a
• /
• pp.129-132
• /
• 2002

대체 에너지(태양광, 풍력등)의 전력저장 시스템으로 널리 사용되는 겔형(Gel Type) 밀폐형 연(鉛)축전지의 노화 특성 평가 및 충전회로에 관하여 연구하였다. 납 합금을 이용한 기판 주조 기술과 전해액(Gel) 배합기술이 축전기 성능과 수명을 좌우하며 또한 배터리 충전 시스템에 따른 온도 상승이 치명적인 영향을 미치게 된다. 따라서 본 연구에서는 적외선 열화상 장치를 이용한 내부 열원 추적에 의해 노화정도를 측정하며 축전지 수명시험을 통해 입수한 데이터와 비교 평가하고자 한다. 현재 실험실 충방전 수명시험을 마치고 (주)코윈텍이 부안 해창 공원에 설치한 30kW급 풍력발전 시스템에 적용하여 Field Test를 시험중이다.

• The Korean Journal of Rheology
• /
• v.10 no.4
• /
• pp.217-226
• /
• 1998

The anisotropy caused by the fiber orientation, which is inevitably generated by the flow during injection molding of short fiber reinforced polymers, greatly influences dimensional accuracy, mechanical properties, and other quality of the final product. Since the filling stage of the injection molding process plays a vital role in determining fiber orientation, an accurate analysis of flow field for the filling stage is needed. Unbalanced filling occurs when a complex or a multi-cavity mold is used leading to development of regions where the fiber suspension is under compression. It is impossible to make an accurate calculation of the flow field during filling with the analysis assuming incompressible fluid. A mold with four cavities with different filling times was produced to compare the numerical analysis results with the experimental data. There was a good agreement between the experimental and theoretical results when the compressibility of the polymer melt was considered for the numerical simulation. The fiber orientation states for compressible and incompressible fluids were also compared qualitatively as well as quantitatively in this study.

• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.98-103
• /
• 2015

Liquefied petroleum gas can be charged up to 85% of cylinder volume by enforcement regulations of safety control and business of liquefied petroleum gas act. The charged mass by enforcement regulations is considered by liquid expansion of internal liquefied petroleum gas at $65^{\circ}C$. But the temperature of liquid would not be suspended under $65^{\circ}C$ in a cylinder or portable vessel at certain situation. In the thermodynamics view point, the cylinder can be exposed to high pressure by liquid expansion. Consequently, it can be possible to potential risk such as physical explosion. Hence, this paper will offer a method of estimated internal pressure by liquid expansion at critical state in the closed system. Also, the structural factor which is given rise to volume increasement of cylinder is offered by experiment. This paper is expected as crucial reference for a cylinder design of liquefied petroleum gas.