• Geophysics and Geophysical Exploration
• /
• v.14 no.4
• /
• pp.282-288
• /
• 2011

One of the most challenging issues facing shallow seismic survey is how to generate large amplitude of high frequency signal with small seismic sources. We tested the performance of the most commonly used shallow seismic source, hammer, with four plates: PE, nylon, aluminum, and steel plates. We compared their signal powers in terms of impulsive forces, accelerations, and ground vibration velocities caused by hammer impacts. According to a previous work, hammer blowing to an aluminum plate would generate the largest amplitude among four combinations. However, it was found in this experimental research that aluminum plate delivers seismic wave energy to the ground less than that generated with steel or PE plate. Even though the amplitude is relatively small, plastic plates could provide seismic pulses of 180 ~ 200 Hz in the bandwidth, and it seems to be very hard to generate seismic energy over the frequency of 250 Hz.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.2
• /
• pp.129-136
• /
• 2011

The aim of this paper is to present the method of identifying the impact location on the plate. This basic research has the future purpose to achieve the human-interaction technology based on the signal processing, piezoelectric materials, and wave propagation. The present work concerning the location identification of a single impact on the plate simulated the waveform numerically generated by impact force and applied the SWFOM(sliced Wigner higher fourth order moment) to the waveform to get the arrival time differences due to impact force between three sensors attached to the plate. The simulated signal is useful to get the information for time interval for the only direct wave. This information is used the source localization by using experimental work. The measured signal is also used for source localization of a single impact based on the higher order time frequency as a novel work.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.10
• /
• pp.960-967
• /
• 2010

The sound field can be classified to the direct, diffract and reverberant sound field. If the sound absorption material in a room is not applied sufficiently, the reverberant sound field increases and the sound pressure in a room also increases when the sound source exists in a room. Therefore, the reverberation time should be controled in order to reduce the reverberant sound as well as sound pressure level in a room. Even though the reverberation time is specified and researched widely in architectural engineering, it is rarely performed in a marine engineering. Therefore, in this research, the reverberation time in a navel vessel is researched related to the noise reduction in a cabin.

• Proceedings of the Acoustical Society of Korea Conference
• /
• autumn
• /
• pp.427-432
• /
• 1999

When a high-speed train enters a tunnel, a compression wave is generated. This wave subsequently emerges from the exit portal of the tunnel, which causes an impulsive noise called 'Sonic boom' or 'micro-pressure wave'. In the present study, new method is presented for prediction of sonic boom noise, especially focusing on the effect of the nose shape of the train on the resultant noise. Acoustic theory for monopole source is used to represent a nose shape of the train in wave equation. Compression wave propagation in tunnel considering tunnel track condition and emission of sonic boom was calculated. The predicted compression waves and impulsive sound waves are compared with recent measurements, and show reasonable agreements.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.68-73
• /
• 1995

반사음이 포함된 신호의 계측을 통하여 원음의 크기와 반사계수의 크기, 지연시간 등의 추출을 수치적 예를 사용하여 규명해 보았다. 반사계수의 측정시, 폐쇄된 음장에서는 정상파비로 표시되는 단일 주파수 신호를 사용하는 것이 실제 계측시 가장 손쉬운 방법이며, 광역의 주파수 성분에 걸쳐 그 값을 파악할 필요가 있는 경우에는 켑스트럼 상에서 반사파의 효과가 원음과 확연히 구분되는 신호를 사용하는 것이 신호처리 과정에서 불필요한 부담을 제거시켜 준다. 개방 음장에서는 반사파가 1개 밖에 포함되지 않으므로 이 경우에는 PSD 상의데이터 처리를 통하든지 또는 캡스트럼의 재편집을 통하여 원음의 크기와 성분 그리고 반사계수 등을 손쉽게 추출해 낼 수 있다. 광대역 주파수 성분을 가진 음원을 계측에 사용할 경우에는 comb lifter의 적용에 보다 세심한 주의를 기울일 필요가 있으며 켑스트럼 상의 추가 충격응답함수의 식별에 보다 더 합리적인 방법이 강구되어야 할 것이다.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.32 no.10
• /
• pp.17-21
• /
• 2003

국내 화장실 양변기의 배수 및 세정소음에 관한 실험실 측정결과를 소개하고자 한다. 1989년 대한주택공사에서 조사한 설문조사에 의하면 공동주택에서 외부로부터 들리는 소음에 대한 불만을 조사한 결과, 바닥충격음, 급배수설비 소음, 그리고, 공기전달음의 순으로 나타났다. 이와 같이 급배수시 발생소음은 공동주택 입주자의 주요한 민원중의 하나이다. 급배수설비 소음은 유체의 유동에 의하여 발생하며, 직접 공기중을 전파하여 가는 “공기전달음”과 배관지지 재료 및 구조체 등을 통해 재차 공기중을 전파하여가는 “고체전달음” 으로 구분된다. 여기서 “공기전달음”이란 실내에서 발생한 소리가 구조체를 진동하고 구조체는 인접실의 구조체 주변의 공기를 진동하여 소리가 방사되거나 또는 인접실간에 열려 있는 통로를 거쳐 전달되는 소음을 말하고 “고체전달음”이란 음원이 접하고 있는 건물구조체를 통하여 진동의 형태로 전달되는 소음을 일컫는다. 공동주택에서 배수관은 아래층 천장배관에 해당되므로 배수관에서 발생하는 소음은 아래층으로 직접 전달된다. 이러한 배수설비 소음은 배관재의 종류, 배관스페이스의 구조 및 위치 등에 따라 소음레벨이 달라지게 된다.(중략)

• The Journal of the Acoustical Society of Korea
• /
• v.10 no.2
• /
• pp.52-60
• /
• 1991

Sound propagation in a sloping sea bed ocean environment demonstrates ray curvature in a direction parallel to the shoreline. The theoretical analysis of this shows that an ensonified region and a shadow region are formed, and their spatial extents depend on the spatial coordinates of source and receiver, a sloping angle and sourece frequency. The purpose of this experimental study using a sloping sea bed model is to check the theoretical prediction as a part of an ongoing investigation in the ocean environment. The sloping sea bed model used in this experiment had an ideal pressure-release boundaries and a sloping angle of $220.5{\circ}$ A single frequency signal and an impulsive signal were used as omnidirectional point sources. The spatial acoustic field characteristics in the across slope direction were measured using the former and the frequency dependent field characteristics in a specific point were obtained using the latter. It has been found that the analysis for the spatial extent of shadow zone and the frequency dependent field characteristics in the across slope direction, has a good agreement with the theoretical solution.

• The Journal of the Acoustical Society of Korea
• /
• v.26 no.7
• /
• pp.343-352
• /
• 2007

The present study aims to investigate the design standard for acoustic criteria of Korean traditional music which could be used for the design of Korean traditional music halls. In order to do this, subjective listening tests were undertaken to musicians using auralized sounds which were convolved with the impulse response of traditional instruments recorded in an anechoic chamber. 94 pairs of sound were made which have different value of acoustic parameters including RT, BR, Brilliance, G, C80, ITDG, IACC. A paired comparison method(PCM) was used to analyze the results from the subjective listening tests. The results show that the preference of acoustic criteria for the Korean traditional music is far different from those of western music. As a result, specific range of acoustic criteria were suggested for the appropriate acoustic conditions of Korean traditional music. Also, a guideline of the acoustic design of halls for performing the Korean traditional music was suggested which could be used as a basic reference in the future works.

• The Journal of the Acoustical Society of Korea
• /
• v.15 no.4
• /
• pp.32-35
• /
• 1996

The pressure pulses generated from the underwater electric spark system ranged from 0.4 to 1.6kJ are measured with the variation of source depth and range. The characteristics of pressure pulses obtained through this experiment continue to show the same electric energy and depth dependence previously reported, but two particular phenomena are observed. First, it is observed that the peak pressure of the 1st bubble pulse induced from implosion is higher than that of the initial shock wave, which is particularily apparent to high electric energy more than 10kJ previous studies. Second, it has been reported that the energy ratio (potential energy of bubble/intrinsic energy of source) has some tendency to "droop" on the low electric energy as 0.02 for 5kJ and 0.01 for 1kJ but the results of the present experiment show that it continues to have the ratio of 0.01 near 1kJ again.

• KOMUNHWA
• /
• no.70
• /
• pp.133-161
• /
• 2007

It is judged that celadons with '○' pattern and '⊙' pattern have the indication of manufacturer by engraving mark at the internal center of the bottom. These celadons were produced at No.8.23.27 kiln sites located at Sadang-ri(사당리), Daegu-myon(대구면), Gangjin-gun(강진군), Jeollanamdo(전라남도), Korea and '⊙’ patterned celadon porcelain was found only at No. 23 and 27 kiln sites, so it is assumed that its production sites were limited. Kinds of celadons included bowl, dish, cup, bottle, case and vessel for emptied wine and there were a lot of dishes with a variety of patterns. These celadons were engraved by molded design technique using the same ceramic design as the pattern of celadons in the period of their prosperity and it was appropriate method to produce celadons of a good quality with production method to keep decorative design like pattern or size uniformly. It was also found that inlay method was not universalized in this period and similar celadons were produced with molded design in large quantities. These celadons had partially fire clay temper, but most of them were burnt by supporting the inner bottom of U-type base with quartzite after whole glazing. It was known through relics excavated at Seokreung(석릉) royal tomb of King Heejong(희종) at Ganghwa(강화) and Hyeeumwon(혜음원) temple site at Paju(파주) and military house at Wakamiyaoji(약궁대로) avenue Kamakura(겸창)-city, Japan(일본) that these celadons were manufactured at two quarters of the 13th century centering around 1230s. Therefore, these celadons will be significant materials to fill the gap of the celadons in the 13th century resulted from the record chronologically that green celadons were manufactured in the 12th century. And this period was invaded by Mongolia(몽고), but central control was achieved and green celadons were continuously produced. It was also considered that these celadons were excavated at Gabgot-ri(갑곶리) and Gwanchung-ri(관청리), Ganghwa(강화), Hyeeumwon temple, Paju which played the role of temporary palace, Bu1guksa(불국사) temple at Gyeongju(경주), Silsangsa(실상사) temple at Namwon(남원) and relics of Jangheung(장흥) adjacent to Daeguso(대구소) and these were produced for high class.