• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.4
• /
• pp.31-39
• /
• 2001

Composite propeller shafts for a vehicle have major advantages such as reduction of vibration, noise, and weight. A propeller shaft was designed with a carbon/epoxy composite material using the finite element method(FEM), and prototype shafts for tests were manufactured by the filament winding manufacturing process. In order to verify the design procedure by FEM, Two kinds of experimental tests were carried out using a FFT analyzer with impact hammers and a critical speed measuring apparatus for measurement of natural frequencies and critical speeds. The difference between the FEM analysis result and the test result was less than 3.4%, showing FEM analysis results to be acceptable. The parametric study was focused on determining the factor affecting the vibration and strength characteristics of the propeller shaft based on FEM. In investigation of the change in natural frequency without an increase in propeller shaft weight, it was found that the winding angle is the most significant factor affecting the vibration and strength characteristics.

• Fire Science and Engineering
• /
• v.29 no.1
• /
• pp.53-59
• /
• 2015

Water hammering created by an unsteady flow in pipeline systems can cause excessive change in pressure, vibration, and noise. So, water hammer analysis is very important for limiting the damage caused to pipeline, pump and valve systems by operation conditions. On the other hand, water hammer arrester has been manufactured and used in order to minimize the damage caused by water hammering phenomenon in domestic, and it has been produced and installed as the low cost-oriented because of being no separate standard in the meanwhile. Therefore, our research team investigated about the standardization of water hammer arrester performance through the various methods, such as test methods for verification of one pipe, assuming the occurrence of water hammer in a water-based fire extinguishing system, separated for opening impact pressure and shut off impact pressure and for a branch pipe in order to make guideline for water hammer arrester performance. And finally, verified the performance of the water hammer pressure as the simple mechanical way using the U-shaped pipe and a test weight, so KFI standards for the water hammer arrester could be established.

• Explosives and Blasting
• /
• v.36 no.4
• /
• pp.48-61
• /
• 2018

This case study is concerned with the project of the explosive demolition for the KOGAS office building located in Bundang district in Seongnam city. Since the office building was a kind of long-span beam structures, a mechanical demolition method using jacking support systems was considered in the beginning of the project. With consideration of the excessive reinforcement cost, uncertainty of safety, and prolonged construction period, however, the original plan was later changed to use an explosive demolition method. For the purpose of protecting nearby buildings and facilities during the collapse process, the explosive initiation sequence was elaborately designed to bring down the building structure towards its front left corner. A total of over 550 electronic detonators (Unitronic 600) was used to sequentially initiate the explosives installed at appropriate columns in the first, second, and fifth floors. To diminish dust production, water bags of small and large sizes were respectively installed at each column and on the floors to be blasted. As such, every effort was exercised to mitigate overall noise, dust, and shock vibrations that could be generated during the explosive demolition process for the office building.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.2
• /
• pp.346-353
• /
• 2022

Recently, studies on the integrity of rotating machines, such as gantry cranes, which are used in the shipbuilding industry, have been actively conducted. Gantry cranes are driven at relatively low revolutions per minute (RPM), are frequently operated and stopped, and are impacted by external environmental factors, such as shock and noise in the measurement data. The purpose of this study was to construct a replica of a gantry crane hoist used in indoor shipbuilding and analyze the acquired data for errors caused by the shift in operating conditions (RPM) and the change in the position of the data acquisition sensor. Consequently, we observed that the error caused by differences in sensor positions did not occur significantly under low operating conditions but occurred significantly under relatively high operating conditions. Thus, we determined that both the operating condition and position of the acquisition sensor affected the data acquired by the rotary machine.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.53-53
• /
• 2017

연구목적: 국내 과일 산업의 한 단계 도약과 대외 경쟁력을 높이기 위해서는 수확작업의 기계화가 시급함. 이 연구는 국내외 과일 수확 기계화 현황과 문제점을 분석하고, 향후 수확작업 기계화 방향을 제시하고자 수행 수확기계 실용화 현황 및 고찰 (국내) 과일을 직접 수확이 아닌 수확 작업을 보조해주는 고지 작업기(수동형, 모터 진동형)와 고소 작업차가 대부분임. 수동형은 사과 감 등을 수확하지만, 작업능률이 낮고 작업자가 쉽게 피로하여 장시간 작업이 불가능하므로 실질적인 대안이 되지 못함. 진동형은 자체 동력을 이용하여 나무에 진동을 가하여 주로 대추 매실 등 소과류 수확에 이용되고, 수확능률은 우수하나 충격 손상이 많아 개선이 요구됨. 고소작업차는 동력원에 따라 충전식과 엔진식으로 구분되고, 충전식은 엔진식에 비해 진동 소음이 적어 쾌적하지만, 작업시간이 배터리 용량에 제한을 받음. 또한 작업대 작동방식에 따라 리프트형과 붐형으로 구분함. 리프트형은 리프트를 이용하여 작업대를 상하로 구동하는 방식으로 높은 위치의 과실 수확이 어렵고, 작업대 넓이 만큼의 작업 공간(과수간의 거리)이 필요함. 붐형은 필요한 곳으로 접근성이 우수하나 무거운 무게를 지탱하기 어렵기 때문에 본체를 무겁게 하거나 수시로 수확된 과일을 하차시켜야 함. (국외) 수확 후 가공되는 과일류와 포도 올리브 오렌지 매실 등 소과류 수확이 기계화되었지만, 사과 복숭아 등 신선과일은 아직도 외국의 값싼 노동자들에 의존하여 수확되고 있음. 현재 실용화된 수확 기계는 진동식 수확기계와 터널식 수확기계가 대표적임. 진동식은 집게형의 부착기를 나무 줄기에 고정한 후 트랙터 동력원으로 나무에 진동을 가하여 수확하고, 올리브 대추 등과 같은 소과류와 과피가 두꺼운 오렌지 등에 적용되고, 수확 작업능률이 매우 높으나 과일의 낙하 상처를 피할 수 없는 단점이 있음. 터널형은 규격화(과수 크기 및 형태, 재식거리)된 과수원에 잘 적응하도록 설계 제작되어, 과수 위를 지나가면서 내부에 설치된 진동장치와 컨테이너로 과일을 수확하고, 와인용 포도 수확기가 대표적임. 기계수확이 가능하도록 과수원 조성단계에서부터 재배양식(과수 좌우 및 전후 거리)을 기계의 제원(바퀴 간격, 작업부 간격 등)에 맞추어 재배함. 과일 수확로봇에 관한 연구는 활발하고 일부에서 실증시험단계에 있음. 결론: 구체적인 추진방향을 제시하면, 단기적으로는 과일 수확작업자의 작업편이성과 노동강도를 줄일 수 있도록 소형 저가 범용성이 우수한 보조기구/기계의 보급을 확대하고, 중장기적으로는 수확기계/수확로봇 개발을 위한 연구개발비 투자를 늘리는 동시에, 기계/로봇이 과수원에 잘 적응할 수 있도록 수형 재식거리 등 재배양식의 표준화가 추진되어야 함.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.12
• /
• pp.8408-8415
• /
• 2015

The purpose of this study is to propose and analyse new technology of structural elements design for Korean-style house(Hanok). Design of modern apartment building adopts many aesthetic elements from Hanok, however, these are only for the decorations of interior. In this study, projected Hanok eaves were studied in terms of the length of solar insolation. Inclined front slab system has been proposed utilizing sloping roof to an apartment building section. This system can provide the same sunshine radiation length and outside view to all levels of building to overcome the limitation of traditional hanok. It also can be applied to all residences the vertical garden concept of hanok. Inclined slab system showed 20% more efficient than flat slab system in terms of solar insolation length. This study also suggested a double deck slab system for not only reducing apartment floor impact noise but also connecting concept of traditional maru system in hanok. Double deck system reduces 66% of floor impact noise comparing with single deck slab of modern apartment buildings.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.2
• /
• pp.249-260
• /
• 2014

When a train enters the tunnel at high speed, the pressure wave occurs. When this pressure wave reaches at the exit of tunnel, some are either emitted to the outside or reflected in tunnel by the form of expansion wave. The wave emitted to the outside forms the impulsive pressure wave. This wave is called 'Micro Pressure Wave'. The micro pressure wave generates noise and vibration around a exit portal of tunnel. When it becomes worse, it causes anxiety for residents and damage to windows. Thus, it requires a counterplan and prediction about the micro pressure wave for high speed railway construction. In this paper, the effects of train head nose and tunnel portal shape were investigated by model test, measurement for the micro pressure wave at the operating tunnel as well as numerical analysis for the gradient of pressure wave in the tunnel. As results, a method for predicting the intensity of the micro pressure wave is suggested and then the intensity of the micro pressure wave is analyzed by the tunnel length and the cross-sectional area.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2008.03a
• /
• pp.51-68
• /
• 2008

When the train enters into a tunnel a high speed, pressure waves are generated inside the tunnel. The pressure waves at propagate in a form of compression wave toward the tunnel exit and a fraction of the compression waves that arrives at the exit of the tunnel are discharged to outside of the tunnel and the remainder is reflected into the tunnel as expansion waves. The compression waves emitted from the tunnel does not radiate in a specific direction but in all directions. If the amplitude of the compression wave is great, it causes noise and vibration, and it is called "Micro-Pressure Wave." "Micro-Pressure Wave" must be considered as a decision for the optimum tunnel cross-section as the amplitude of the compression wave depends on train speed, tunnel length, area of tunnel and train. Therefore, this paper introduces the case study of Micro-Pressure Wave characteristics for determination of tunnel cross section in Honam high speed railway, the pressure inside the tunnel and the micro-pressure waves at tunnel exit were measured at Hwashin 5 tunnel in Kyungbu HSR line. At the same time. a test of train operation model was performed and then the measurement results and test results were compared to verify that the various parameters used as input conditions for the numerical simulations, which were appropriate. Also a model test was performed, in order to analysis of the Micro-Pressure Wave Mitigation Performance by Type of Hood at Entrance Portal.

• Proceedings of the Korea Contents Association Conference
• /
• 2008.05a
• /
• pp.792-795
• /
• 2008

AGT system is a kind of light railway train. AGT system use of concrete track and rubber tire, so it can be reduce the noise and vibration, compare to the normal train system. And, the dynamic responses of normal bridge are influenced by the dynamic characteristics of bridge, the speed of vehicle and the surface roughness of railway. But the AGT system bridge is influenced not only the above facts but also the guiderail unevenness, because, AGT vehicle steered by guiderail. So, in this study, optimized service condition is suggested for the design and operation of AGT system, by the means of experimental study. The experiments are executed for PSC bridge with length of 30m, at the AGT test line in Kyongsan. The test results are compared and investigated according to the prominence. In the test result, the guiderail prominence influenced on the dynamic response of bridge. It shows a increase as compared with no guiderail prominence in the dynamic response value acceleration, displacement, stain.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.10
• /
• pp.2503-2508
• /
• 2014

This study is about the selection and noise test of electronic sensor which is preceded by electric Operating Cell(EOC) development using electronic sensor technology to solve the structural weakness of Mechanism Operated Cell(MOC) in VCB, and has a final target in product development minimizing contact malfunction of the chattering or rebounce states caused by existing MOC. In this test results, when opening and closing VCB, rising velocity of surge voltage in opening time was measured 4.2 times faster than closing time and noise decibel value was measured respectively 120dB and 110dB. When supplying 60kV power frequency overvoltage, we found that sensor output graph in VCB opening and closing times operated stably without distortion. When supplying 150kV $1.2{\times}50{\mu}s$ impulse frequency voltage, we found that voltage graph of output contact in sensor opening and closing sides maintained a normal condition without distortion, and when supplying 2500A current, we found that tested result of electric field noise operated stably without distortion.