• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.708-716
• /
• 2013

This study aims to understand the applied forces and related vibrational characteristics of a tripod joint (TJ), which is mostly used in front-drive-type middle-sized sedans in South Korea. The plunging force (PF) and generated axial force (GAF) are the most influential quantities related to the vibrational characteristics of a driveshaft. To obtain meaningful data, specially designed tests were performed using MTS test sets. The results of direct measurements reveal that higher PF and GAF values appear to worsen the vibrational characteristics of the vehicle. On the other hand, the measured apparent mass is useful for calculating the applied forces for a short driveshaft that has no dynamic vibration absorber. Among diversely controlled samples, it shows that the viscosity and tight fit are very sensitive to shudder vibrations of the vehicle. Therefore, these are good design factors for quality controls in the production line of constant-velocity joints.

• Tribology and Lubricants
• /
• 제10권2호
• /
• pp.43-50
• /
• 1994

The hydrodynamic bearing is accepted in many rotating systems because it has a large load carrying capacity. But the anisotropic pressure distribution of the bearing can arise the unstable vibration phenomenon over a certain speed. The magnetic bearing is an active element so that the unstable phenomenon of the hydrodynamic bearing, which is induced by the anisotropic support pressure of the oil film, can be controlled if the control algorithm and the controller gains are chosen appropriately. In this study, we investigate the stabilization method of the hydrodynamic bearing system composing the hybrid bearing which is the single unit of hydrodynamic bearing and magnetic bearing. The load carrying conditions of the hybrid bearing is modelled by the sum of the stiffness and damping coefficients of the hydrodynamic and the magnetic bearings in each direction. The dynamics of the rotor is analyzed by the Finite Element Method and the stability limit is determined by the eigenvalues of the hybrid bearings and shaft system. The eigenvalue study of the system shows that the stability limit of the hybrid bearing is increased compared to that of the hydrodynamic bearing. A Small increment of the stiffness and damping coefficient of the hybrid bearings by the magnetic actuators can increase the stability limit of the system. In this paper we tried to show the design references of the hybrid bearings by using the nondimensional bearing parameters. The analysis results show the possibilities of the stability limit increment of the hydrodynamic bearing system by combining the magnetic bearing.

• 전산구조공학
• /
• 제3권3호
• /
• pp.141-146
• /
• 1990

본 연구에서는 다목적연구로 반응도제어장치의 제어봉에 대한 내진해석을 수행하였다. 해석모델은 물속에 잠겨있는 두개의 관(중성자흡수봉 및 유동관)이 동심축상에 있으며 부분적으로 중첩된 두 관끝단의 유체틈에 의해 서로 동적으로 연결되어 있다. 유체에 의한 동적질량을 고려한 고유진동수를 구하고 안전정지지진에 의해 발생하는 최대응력과 최대변위를 동위상 및 역위상 거동별로 각각 구하였다. 해석결과 최대응력은 허용치보다 작게 나타나 구조적인 건전성은 입증되었으나, 최대변위는 두 개의 관이 서로 부딪히고 중성자흡수봉은 주위의 다른 벽에도 부딪히는 현상을 수발함을 알 수 있었다.

• 대한기계학회논문집A
• /
• 제33권10호
• /
• pp.1108-1118
• /
• 2009

A Very High Temperature Gas Cooled Reactor (VHTR) has been selected as a high energy heat source of the order of $950^{\circ}C$ for nuclear hydrogen generation, which can produce hydrogen from water or natural gas. A primary hot gas duct (HGD) as a coaxial double-tube type cross vessel is a key component connecting a reactor pressure vessel and an intermediate heat exchanger in the VHTR. In this study, a structural sizing methodology for the primary HGD of the VHTR is suggested in order to modulate a flow-induced vibration (FIV). And as an example, a structural sizing of the horizontal HGD with a coaxial double-tube structure was carried out using the suggested method. These activities include a decision of the geometric dimensions, a selection of the material, and an evaluation of the strength of the coaxial double-tube type cross vessel components. Also in order to compare the FIV characteristics of the proposed design cases, a fluid-structure interaction (FSI) analysis was carried out using the ADINA code.

• 한국자동차공학회논문집
• /
• 제7권7호
• /
• pp.221-228
• /
• 1999

A full-time four wheel drive vehicle is driven literally full time by the front and the rear wheels. Front and rear drive shafts are rotated rapidly in the extremely torsional state, which can cause various vibration and noise problems. The purpose of this study is to reduce the vibration and the noise of the full -time four wheel drive vehicle. In this paper, both the causes and the methods for reduction of torsional vibration are suggested. For this study, the characteristics of the torsional vibration are analyzed by free and forced torsional vibration simulation. And this paper described the influence upon the torsional vibration with emphasis shafting system. The validity of simulation models is checked by the field test. The forced vibration simulation with the variations of shaft design factors are performed by the checked models. According to the simulation , the resonance region shifts and the torque fluctuation varies in the system,. Finally, the methods and the effects for the torsional vibration reduction in driveline are proposed.

• 한국HCI학회:학술대회논문집
• /
• 한국HCI학회 2007년도 학술대회 1부
• /
• pp.429-434
• /
• 2007

본 논문에서는 기울임 동작에 기반한 휴대기기 상의 사진 감상 UI를 제시하고 사용성을 평가한다. 기존의 기울임 입력 방식의 세가지 조작성 문제(overshooting, fluctuation, 부분 이미지 제시)를 개선하기 위하여, 사진 위치 및 기울임에 의존하는 사진 이동 제어 dynamics 모델을 제안한다. 본 시스템은 기울임 감지용 가속도 센서, 기울임에 의한 사진 이동 제어 dynamics 모델, 다중모달(시각, 청각, 촉각)을 통한 모델 상태 출력부로 구성된다. 센서 입력과 다중 모달 출력을 위하여, 삼성 MITs 4300 PDA의 배터리 팩을 개조하여 3축 가속도 센서와 진동 출력장치 (VBW32)를 장착하였다. 제안하는 시스템은 기존의 대표적인 사진 감상 입력 방법인 버튼과 iPod wheel과 비교하였다. 정량적 비교를 위하여 7명의 사용자에게 100장의 사진 중 20장을 차례로 검색하는 과제를 부여하면서 수집한 로그를 분석하였으며, 정성적인 비교를 위하여 설문 조사를 실시하였다. 실험 결과 제안한 방법이 기존 기울임 기반 dynamics에 비하여 overshooting 횟수를 30%, 사진간 이동 거리를 25%, 이동 시간을 17% 감소하였다. 또한 제안한 방법이 버튼과 유사한 조작성을 갖고 있으며, 버튼과 iPod보다 더욱 흥미성이 뛰어났다. 상업적으로 뛰어난 성공을 거둔 iPod이 다수의 overshooting 발생으로 실제로는 사용성이 떨어진다는 점이 예상치 못한 흥미로운 발견이었다.

• 연구논문집
• /
• 통권27호
• /
• pp.127-139
• /
• 1997

투포원 연사기는 스핀들 1회전에 2회의 꼬임을 부가하여 실의 신축성과 인장강도 및 내마모성을 증가시키며, 특수한 목적의 의장사를 만드는 섬유기계이다. 스핀들 유니트는 고속 회전중에 안정화된 운동이 지속되도록 구조설계가 요구되는 핵심장치로서 스핀들 유니트의 동특성 해석은 고속 스핀들 유니트설계의 최적화를 도모할 수 있을 것이다. 스핀들 유니트는 블레이드와 로타리 디스크로 구성되어 있으며, 스핀들 축에 대하여 회전체 형상을 유지 하고 있다. 동특성 해석을 수행하기 위하여 전달 매트릭스 해석법을 정의하고 해석용 프로그램인 SPINDLE을 이용하여 비틀림과 굽힘 고유진동수를 해석하였으며, 운전회전수에서 변위모우드를 분석하였다.

• 한국기계가공학회지
• /
• 제10권5호
• /
• pp.7-12
• /
• 2011

This study covers the optimum design of the 5-axis machine tool. In addition, the intelligent control secures structural stability through the optimum design of the structure of the 5-axis machine center, main spindle, and the tilting index table. The big requirement, like above, ultimately leads to speed-up operation. And this is inevitable to understand the vibration phenomenon and its related mechanical phenomenon in terms of productivity and its accuracy. In general, the productivity is correlated with the operation speed and it has become bigger by its vibration scale and the operation speed so far. Vibration phenomenon and its heat-transformation of the machine is naturally occurred during the operation. If these entire machinery phenomenons are interpreted through the constructive understanding and the interpretation of the naturally produced vibration and heat-transformation, it would be very useful to improve the rapidity and its stability of the machine operation indeed. In this dissertation, the problems of structure through heating, stability, dynamic aspect and safety about intelligent 5-wheel machine tool are discovered to examine. All these discoveries are applied to the structure in order to enhance the density of it. It aims to improve the stability.

• 한국해양공학회지
• /
• 제19권3호
• /
• pp.31-38
• /
• 2005

Ocean developments gradually move to deep-sea in the 21 century. A deep-sea unmanned underwater vehicle is one of important tools for ocean resource survey. A marine cable plays an important role for the safe operation and signal transmission of a deep-sea unmanned underwater vehicle. The umbilical cable of a deep-sea unmanned underwater vehicle is excited by surface vessel motion and shows non-linear dynamic behaviors. A numerical method is necessary for analysing the dynamic behavior of a marine cable. In this study, a numerical program is established based on a finite difference method. The program is appled to 6000m long cable for a deep-sea unmanned underwater vehicle and shows good reasonable results.

• 한국수소및신에너지학회논문집
• /
• 제24권6호
• /
• pp.566-572
• /
• 2013

In the present study, structure analysis has been performed to understand the deflection and stress distribution for a hybrid street-lamp having a vertical-axis wind turbine and a photovoltaic panel. Modal analysis is also evaluated to avoid resonance gerenerated by sychronism between a turbine and a lamppost. To analyze deflection, stress and frequency, general analysis code(ANSYS-Mechanical 13) is employed in the present work. Throughout structure analysis in the hybrid street-lamp, maximum stress is observed at the connecting position between a turbine blade and a blade supporter. Campbell diagram which is combined the natural frequency of turbine blades and blade passing frequency is presented to analyze a system resonance. It is found that the resonance of the system having a rotating turbine blade and a lamppost can avoid by the optimal selection of geometric parameters of a wind turbine.