• Journal of Korean Tunnelling and Underground Space Association
• /
• v.3 no.1
• /
• pp.51-62
• /
• 2001

In-situ stress measurement using AE (Acoustic Emission) and DRA (Deformation Rate Analysis) is usually carried out under uniaxial loading in the laboratory and it consumes delay time from drilling to testing. Therefore, it should be considered how the lateral stress and delay time influence on the test results for the in-situ stress determination. As the delay time increased, the accuracy of estimating the pre-stress decreased. The pre-stress of the specimen loaded only axially was determined within an error of less than 9% (using AE) and 4% (using DRA). And the specimen on which axial pre-stress and the confining pressure were loaded had an error of less than 17% (using AE) and 14% (using DRA). The results of AE and DRA for field specimens were very similar with each other but smaller than those of hydraulic fracturing method.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.26 no.5
• /
• pp.285-290
• /
• 2006

The evaluation of clamping condition has been regarded as the main issue in the safety-maintenance of the clamped high-tension bolts. For this, this paper proposes a method to estimate the axial stress by measuring the TOF (Time-Of-Flight) of ultrasonic wave, which is based on the acoustoelasticity or the dependency of sound speed on the stress. In this method, however, the variation of sound speed within the range of stress induced under the field condition is very small, and thus the accuracy of the TOF measurement is important. We adopted the phase detection method using tone-burst ultrasonic wave to measure the precise TOF. In order to verify the usefulness of the proposed method experiments are carried out and the results were compared with the stress measured by the strain gage. The results show good agreement with each other, and from these we can conclude that the proposed method is highly useful fnr the evaluation of clamping condition in the clamped high-tension bolts.

• Magazine of the Korea Concrete Institute
• /
• v.7 no.3
• /
• pp.139-148
• /
• 1995

The test results from three one fourth scale models using high strength Reinforced Concrete $f_x=704\;kg/cm^2,\;f_y=5.830\;kg/cm^2$ are presented. Such specimens are considered to represent the critical 3 storics of 60-story tall building of a structural wall system in area of high seismicity respectively. They are tested under inplane vertical and horizontal loading. The main varlable is the level of axial stress. The amounts of vertical and horizontal reinforcement are identical for the three walls testcd. The cross-section of all walls is barbell shape. The aspectratio($h_w/I_w$) of test specimen is 1.8. The aim of the study is to investigate the effects of levels of applied axial stresses on the inelastic behavior of high-strength R /C tall walls. Experimental results of high strength R /C tall walls subjected to axial load and simulated sels rnic loading show that it is possible to insure a ductlle dominant performance by promotmg flex ural yielding of vertical reinforcement and that axial stresses within $O.21f_x$ causes an increase in horizontal load-carrying capacity, initial secant st~ffness characteristics, but an decrease in displacement ductility. energy dissipation index and work damage index of high strength K /C tall walls

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2017.04a
• /
• pp.62-62
• /
• 2017

모터와 스크류를 이용한 경량 식혈기를 처음으로 개발함에 따라 실제 산림의 식재 시험에서 발생될 수 있는 것은 감속기와 스크류의 연결부분의 파괴이다. 이 감속기 축의 파괴는 토양내부의 큰 자갈로 인해 스크류가 낄 경우 식재봉을 좌우로 흔들게 되면 가장 취약한 부분인 스크류와 감속기의 연결부위에 가장 강한 모멘트가 걸리게 된다. 물론 작업자의 부주위가 원인이기도 하지만 감속기(K6G30C. Korea)의 축 지름이 8mm이므로 식재봉을 좌우로 흔들면 굽힘파괴가 일어날 가능성이 높다. 감속기의 축이 파괴가 되지 않게 하는 방법은 재료의 강도가 높은 새로운 감속기를 찾은 일과 기존 감속기의 축을 굽힘응력에 안전하게 대응할 수 있게 설계를 하는 방법이 있다. 본 연구에서는 전자에 대한 조사와 동시에 후자에 대한 설계와 제작을 수행하여 기 제작된 경량식혈기와 비교 분석하였다. 스크류 축의 굽힘응력에 대한 대응 방법으로 감속기 축의 보강방법은 감속기 축에 식재봉으로 부터 굽힘응력이 직접 전달되지 않게 하기 위해 모터 하우징의 하부 위치에 감속기 축을 감싸는 Radial Bearing을 결합하였다. 그리고 스크류의 축은 상단의 지름을 크게 키운 상태로 감속기의 축에 연결하는 방법으로 설계하였다. 이때 식혈봉으로 부터 걸리는 모멘트는 스크류의 상단 지름에 걸리게 되는데 상단부는 모터 하우징의 하단과 단단하게 결합함으로써 감속기 축을 보호하게 되고 또한 감속기 축의 길이에서 Bearing과 스크류 상단부 큰 지름이 각각 반반씩 보호하는 형태로 설계하였다. 이와 같이 감속기의 축을 보강한 경우 종전의 식혈기보다 무게가 무거워지게 된다. 즉, 1차 식혈기 무게는 3.38kgf, 2차 시작기는 3.28kgf, 축 강도가 보강된 3차 시작기는 무게가 3.87kgf로 증가되었다. 따라서 종전보가 약 600g 증가되어 다소 무거운 느낌이 들었다. 여기서 리듐 폴리머 배터리와 가방의 무게 3.23kgf를 부가하면 1차, 2차, 3차 시작기의 무게는 각각 6.61kgf, 6.51kgf, 7.1kgf로 나타났다. 따라서 굽힘응력에 대한 보강의 방안으로 설계된 무게 과다가 현장 시험에서 작업자의 피로도 증가와 작업의 비효율성이 예상되어 포트묘의 현장 식재시에 이에 대한 평가를 수행하여 비교 분석할 예정이다.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.33 no.2
• /
• pp.149-155
• /
• 1997

잔류응력을 측정하는 비파괴 방법중 Neutron diffraction technique의 발달로 인하여 기존의 X-ray diffraction technique에 비하여 잔류응력 측정가능 두께가 대부분의 물질에 있어서 훨씬 깊어졌다. 비파괴 방법으로 부품내의 잔류응력 분포가 측정되어진 경우, 부품의 가공시 잔류응력의 재분포로 인한 형상의 변화를 정량적으로 예측할 수 있는 방법에 대해 어떠한 경우도 논의된 바 없다. 본 연구에서는 축 방향의 잔류응력이 내재하는 strip의 층 가공시 일어나는 strip의 곡율변화를 정량적으로 예측할 수 있는 수식을 제시하였다. 간단히 컴퓨터 프로그램화 할 수 있는 수식을 전개하므로 써 현장에서 유용하게 이용할 수 있게 하였다.

• Journal of the Korea Concrete Institute
• /
• v.17 no.5 s.89
• /
• pp.803-809
• /
• 2005

The purpose of this study is to investigate the mechanical characteristics of plain and steel fiber high strength concrete under uniaxial and biaxial loading condition. A number of plain and steel fiber high strength concrete cubes having 28 days compression strength of 82.7MPa(12,000 psi) were made and tested. Four principal compression stress ratios ($\sigma_2/\sigma_1$=0.00, 050, 0.75 and 1.00), and four fiber concentrations($V_f$ =0.0, 0.5, 1.0 and $1.5\%$) were selected as major test variables. From test results, it is shown that confinement stress in minor stress direction has pronounced effect on the strength and deformational behavior. Both of the stiffness and ultimate strength of the plain and fiber high strength concrete Increased. The maximum increase of ultimate strength occurred at biaxial stress ratio of 0.5($\sigma_2/\sigma_1=0.5$) in the plain high strength concrete and the value were recorded $30\%$ over than the strength under uniaxial condition. The failure modes of plain high strength concrete under uniaxial compression were shown as splitting type of failure but steel fiber concrete specimens under biaxial condition showed shear type failure. The values of elastic modulus were also examined higher than that from ACI and CEB expression under biaxial compression condition.

• Journal of The Korean Society For Urban Railway
• /
• v.6 no.4
• /
• pp.383-392
• /
• 2018

This study investigated the change of additional axial stress of rail and reaction force at bridge bearings due to the track-bridge interaction when laying CWR on non-ballasted railway bridges including truss bridges with relatively long span. According to the results of the present study, additional axial stresses of rail and reaction forces at bridge bearings showed a large increase when CWR is installed on the non-ballasted railway bridge. The additional axial stress of rail can be acceptable if sufficient lateral resistance can be obtained. However, if the reaction force increases, there is a risk of damage of the bearing or pier, and therefore, it is necessary to take measures to mitigate the reaction force. It is found that additional axial stress of rail decreases when considering the frictional resistance of the bridge movable support, but its effect on the bearing reaction force is very small. On the other hand, when the longitudinal track restraint decreases, both additional axial stress of rail and bearing reaction force are reduced to a large extent. Also, when the ZLR fastening devices are applied to the region where the additional axial stress of rail is highest, bearing reaction force as well as additional axial stress of rail greatly decreased. Therefore, the application of ZLR fastening devices with the reduction of the longitudinal track restraints is very effective for installing CWR on non-ballasted railway bridges.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1997.04a
• /
• pp.181-187
• /
• 1997

고강도 알루미늄 합금 링롤재의 급냉, 링 팽창(expansion) 및 링 압축(compression) 응력제거처리후 잔류응력을 예측하기 위하여 2차원 축대칭 열해석 및 탄소성 해석을 수행하였다. 급냉 및 응력제거처리 후 2단 과시효 처리(T73)된 링롤재에 대하여 3단계 절단법(Three step sectioning method)을 적용하여 링롤재의 두께에 따른 잔류응력 분포를 측정하였으며, 측정결과를 급냉 및 응력제거처리후 잔류응력 해석결과와 비교분석하였다. 링의 급냉후 원주 및 축방향의 잔류응력 해석값은 T73후 측정값과 비슷한 경향을 보였으며, 링의 내면과 외면에서 압축응력을 나타내었고 중심에서 인장응력을 나타내었다. 잔류응력은 링 팽창(T7351) 및 링 압축(T7352) 적용후 T73에 비해 현저히 감소하였으며, 축방향의 제거 효과가 원주방향보다 우수하게 나타났다. 또한 링 압축에 의한 제거효과가 링 팽창보다 크게 나타났다. 링롤재의 응력제거처리는 제거 효과 및 실용성 측면에서 링 압축 공정이 유리하며, 치수제어 및 장비용량 측면에서 링 팽창 공정이 유리하다는 결론을 얻었다.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1479-1485
• /
• 2010

In recent times, due to wire drawing of high carbon steel at a high speed to ensure a high productivity and high strength, axial residual stress are generated because of rapid increase in surface temperature. In the process, the temperatures of the wires increased because of the deformation of the wires and the friction between the die and wire. In particular, in the case of the wire drawing at a high speed, friction leads to a large temperature gradient so that considerable axial residual stress is generated on the surface. In this study, the relationship between axial residual stress and increase in the surface temperature was investigated, and a prediction model of uniform temperature was proposed. Then, a prediction model for residual stress was developed. The proposed model was verified by measuring the residual stress by X-ray diffraction on drawn wires.

• Journal of the Korea Concrete Institute
• /
• v.15 no.2
• /
• pp.335-343
• /
• 2003

In the previous experimental study, it is verified that the ultimate strain of concrete (${\varepsilon}$$_{cu}$=0.003) and coefficient of equivalent stress block (${\beta}$$_1$) can be used for the analysis of RC beams under biaxial and uniaxial bending moment. However, the characteristics of stress distribution of non rectangular compressed area in the RC columns are different to those of rectangular compressed area. The properties of compressive stress distribution of concrete have minor effect on the pure bending moment such as beams, but for the columns subjected to combined axial load and biaxial bending moment, the properties of compressive stress distribution are influencing factors. Nevertheless, in ACI 318-99 code, the design tables for columns subjected to axial loads with bidirectional eccentricities are based on the parameters recommended for rectangular stress block(RSB) of rectangular compressed areas. In this study the characteristics of stress distribution through both angle and depth of neutral axis are observed and formulated rationally. And the modified parameters of rectangular stress block(MRSB) for non rectangular compressed area is proposed. And the computer program using MRSB for the biaxial bending analysis of RC columns is developed and the results of MRSB are compared to RSB and experimental results respectively.