• Journal of Advanced Marine Engineering and Technology
• /
• 제31권4호
• /
• pp.335-342
• /
• 2007

A propulsion and lift shafting system in an air cushion vehicle is flexible multi-elements system which consists of two aeroderivative gas turbines with own bevel gears, four stage lift fan reduction gear, two stage propulsion reduction gear air propellers and high capacity of lifting fans. In addition, the system includes the multi-branched shafting with multi-gas turbine engines and thin walled shaft with flexible coupling. Such a branched shafting system has very intricate vibrating characteristics and especially, the thin walled shaft with flexible couplings can lower the torsional natural frequencies of shafting system to the extent that causes a resonance in the range of operating revolution. In this study, to evaluate vibrational characteristics some analytical methods for the propulsion and lift shafting system are studied. The analysis, including natural frequencies and mode shapes, for five operation cases of the system is conducted using ANSYS code with a equivalent mass-elastic model.

• 해양환경안전학회지
• /
• 제26권4호
• /
• pp.412-418
• /
• 2020

선박 축계를 구성하는 프로펠러축은 엔진출력, 프로펠러 하중 및 편심추력의 영향으로 인해 거동의 양상이 달라져 선미관 후부베어링의 국부하중 변화를 일으킴으로써 선미관 베어링 손상의 위험을 증가시킨다. 이를 방지하기 위해 수행된 추진축계 정렬연구는 선급강선규칙을 중심으로 주로 축과 지지베어링간의 상대적 경사각과 유막유지를 최적화 하는데 중점을 두어 진행 되어왔다. 그러나 보다 상세한 평가를 통한 추진축계의 안정성 확보를 위해서는 전타와 같은 급격한 선미유동장 변화에 기인한 과도상태를 포함한 동적상태의 고려가 필요하다. 이러한 관점에서, 본 연구는 50,000 DWT 선박을 대상으로 스트레인 게이지법을 이용하여 밸러스트 흘수 상태에서 정격회전수로 운전 중 대표적 동적 과도상태인 우현 전타상태에서의 프로펠러 축 거동이 추진축계에 미치는 영향을 분석하였다. 그 결과 변동된 프로펠러 편심추력은 프로펠러축을 일시적으로 강하게 내려 누르는 힘으로 작용하여 선미관 베어링의 국부하중을 증가시켜 축계 안정성에 부정적 영향을 미침을 증명하였다.

• 해양환경안전학회지
• /
• 제27권7호
• /
• pp.1082-1087
• /
• 2021

프로펠러축은 프로펠러 하중 및 편심추력의 영향으로 인해 정적, 동적, 과도상태 각각 거동의 패턴이 달라져 선미관 후부베어링의 국부하중 변화를 일으킴으로써 선박 축계의 안정성에 큰 영향을 미치며, 결과적으로 축 지지 베어링의 손상위험을 증가시킨다. 이를 방지하기 위한 일련의 축계정렬연구는 선급강선규칙과 조선소 지침을 기반으로 준정적 상태에서 축과 선미관 베어링간의 상대적 경사각과 유막유지, 선체변형에 따른 영향평가를 최적화 하는데 중점을 두어 진행 되어왔다. 그러나 보다 진일보한 형태의 추진축계의 안정성을 보장하기 위해서는 조타장치의 전타시 발생하는 급격한 선미유동장 변화와 같은 과도동적상태변화 조건에서의 상세 연구가 필요하다. 이러한 관점 하에 본 연구에서는 50,000 DWT 중형 유조선을 대상으로 스트레인 게이지법과 변위센서을 이용하여 선박운전 중 대표적 과도상태인 좌현 전타시의 프로펠러 축 거동이 선미관 베어링에 미치는 영향을 교차검증한 결과, 프로펠러 편심추력변동이 선미관 베어링의 하중을 일시적으로 저감시켜 베어링 하중을 완화시키는 것을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권1호
• /
• pp.18-24
• /
• 2000

As ship's propulsion shafting system has been complicated, many linear methods that have been used until now are not sufficient enough to produce proper solutions and these solutions are ofter unreasonable. So we need to solve nonlinear systems, and many methods for solving nonlinear vibration system have been developed. In this study, the propulsion shafting system was modeled with Duffing's nonlinear vibration system and multi-degree-of-freedom, and analyzed by using Quasi-Newton method. And for the purpose of confirming the reliability of the calculating results for nonlinear forced torsional vibration of the propulsion shafting system, the nonlinear calculated results were compared with the linear calculated ones for ship's propulsion shafting system. In the result, for analysis of the forced torsional vibration of the propulsion systems with nonlinear elements, the modified Newton's method is confirmed reasonable.

• 소음진동
• /
• 제10권4호
• /
• pp.655-661
• /
• 2000

Diesel power plant can be used as a power supplier for the isolated place where consumption of electric power is variable. The reason is that mobility and durability of diesel engine is superior to those of other thermal engines. However, there are some disadvantages for using these diesel engines such as bigger vibratory excitation force comparing to the others, which result from high combustion pressure of cylinders and inertia force of piston reciprocating masses. In this paper, control and optimization of torsional vibration of 12K90MC-S engine for diesel power plant using uneven crank angles is identified by theoretical analysis and vibration measurement.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2012년도 전기공동학술대회 논문집
• /
• pp.175-175
• /
• 2012

Proper shaft alignment is one of the most important actions during the design of the propulsion system. The stiffness of recently designed marine propulsion shafting has been increasing remarkably, whereas hull structures have become more likely to deform as a result of optimized design of the scantlings and the high tensile steel. Therefore, to obtain the optimum status in shafting alignment at the design stage, it is strongly recommended that the change of bearing reaction force depending on ballast/load condition, the bending moment force occurred by propeller thrust, elastic deformation of bearing occurred by vertical load of shaft mass and etc., should be considered. This paper dealing with introduction of shaft alignment concerning long shaft for high speed vessel and review its reliability evaluation theoretically.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 춘계학술대회 논문집
• /
• pp.173-179
• /
• 2001

The torsional or axial critical vibration of the order coinciding with the number of propeller blades is simultaneously excited by the harmonic tangential or radial forces acting on the crank shaft and by the harmonic of the same order from the propeller. The exciting torque of propeller is relatively small comparing with that of crank side, but the exciting force of propeller rather larger than that of crank shaft. With this situation, the exciting force of propeller cannot neglect if the axial vibration of propulsion shafting is calculated. With the propeller in its optimal angular position, i.e. its excitation effect opposed to that of the engine, the stresses at the critical revolution will largely cancel themselves out. In this paper, a method of optimizing the angular propeller position with regard to torsional and axial vibration is studied. The optimal relative angle is determined theoretically by calculation results of coupled torsional-axial vibration.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.301-306
• /
• 2000

Small passenger and car carrier ships are mainly used as a connection way between land and small islands. And these ships should be designed to enlarge the capacity of passenger and car loading within limited space and draft. So the resonances of various vibrations exist in normal operation range of engine and propulsion shafting. In this paper, hull's superstructure vibration which was especially induced by the 1st order excitation of whirling vibration on the 2-engines and 2-propulsion shafting systems is introduced. Also these are verified via the theoretical analysis using transfer matrix method and FEA software ANSYS and its vibration measurement.

• 대한조선학회논문집
• /
• 제43권4호
• /
• pp.512-520
• /
• 2006

The effects of flexibilities of supporting structures on shaft alignment are growing as ship sizes are Increasing mainly for container carrier and LNG carrier. But, most of classification societies not only do not suggest any quantitative guidelines about the flexibilities but also do not have shaft alignment design program considering the flexibility of supporting structures. A newly developed program, which is based on innovative shaft alignment technologies including nonlinear elastic multi-support bearing concept and hull deflection database approach, has S basic modules : 1)fully automated finite element generation module, 2) hull deflection database and it's mapping module on bearings, 3) squeezing and oil film pressure calculation module, 4) optimization module and 5) gap & sag calculation module. First module can generate finite element model including shafts, bearings, bearing seats, hull and engine housing without any misalignment of nodes. Hull deflection database module has built-in absolute deflection data for various ship types, sizes and loading conditions and imposes the transformed relative deflection data on shafting system. The squeezing of lining material and oil film pressures, which are relatively solved by Hertz contact theory and built-in hydrodynamic engine, can be calculated and visualized by pressure calculation module. One of the most representative capabilities is an optimization module based on both DOE and Hooke-Jeeves algorithm.

• 대한조선학회논문집
• /
• 제42권5호
• /
• pp.479-486
• /
• 2005

The final goal of shift alignment design is that the bearing reaction forces or mean pressures are within design boundaries for various service conditions of a ship. However, it is found that calculated bearing load can be substantially variable according to the locations of the effective support points of after sterntube bearing which are determined by simple calculation or assumption suggested by classification societies. A new analysis method for shaft alignment calculation is introduced in order to resolve these problems. Key concept of the new method is featured by adopting both nonlinear elastic and multi-support elements to simulate a bearing support Hertz contact theory is basically applied for nonlinear elastic stiffness calculation instead of the projected area method suggested by most of classification societies. Three loading conditions according to the bearing offset and the hydrodynamic moment and twelve models according to the locations of the effective support points of sterntube bearings are prepared to carry out quantitative verifications for an actual shafting system of 8000 TEU class container vessel. It is found that there is relatively large difference between assumed and calculated effective support points.