Journal of the Korean Society for Aeronautical & Space Sciences
/
v.36
no.8
/
pp.780-789
/
2008
A new method for measuring the performance of a micro-thruster is suggested in this paper. A few thrust stands have been developed for measuring micro-level thrusts. This paper describes a different measurement method that can minimize the calibration involved in the measurements, while providing the capability of directly measuring the produced minimum impulse bit directly. The underlying theory and the theoretical background for the measurement mechanism are described here. The theory and method is verified using a computer simulation, and the result is given in this paper. The theory has also been tested on an actual hardware. Although this hardware is a prototype, developed for proof-of-concept analysis, satisfactory results have been obtained.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2012.05a
/
pp.42-45
/
2012
As a basic research for the development of Korean lunar lander, propulsion system development for ground test is in progress. Design target is 220 N in ground thrust at 130 g/s flow rate, 200 psi chamber pressure. For the performance improvement, two type injector and catalyst bed was designed. For ground test, thrust measurement system using LM guide was developed and test was performed. The result shows 214.1 N thrust in atmosphere condition at 126.6 g/s flow rate.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2009.05a
/
pp.379-380
/
2009
한국항공우주연구원 추진기관팀은 1999년 10월에 3,000 lbf 급 고공환경 엔진시험 설비를 갖추고 소형 가스터빈 엔진의 고공환경 성능시험에 이를 활용하고 있다. 하지만 새롭게 2008년부터 고공환경 성능시험을 진행하고 있는 엔진은 1,000 lbf 미만의 초소형 엔진으로써 기존 추력측정 시스템을 이용하여서는 정확한 추력의 측정을 보장할 수 없다. 본 논문에서는 초소형 엔진의 고공환경 성능시험 수행을 위한 추력대의 구축 과정을 다루고 있다.
This paper presents the REA thrusters performance estimation results for the KOREASAT F1&F2 launched in 1995 The satellite tracking data obtained from the ground system from end of 1999 to beginning of the 2000 are used to estimate the thruster performance. The estimation algorithm is derived from the least square estimation theory and designed to estimate the velocity change induced by the on-boarded thruster firing as well as the orbit parameter. The estimation results show that the Koreasat F1 thruster are in bad thruster condition of 64% performance for REA when it fires in on-pulse mode. Here, the performance is defined by the ratio of the resulted velocity change to that of planned. But, in the case o( the Koreasat F2, it is found that the performance approximately reaches up to 100%, even after the 5 years of the mission.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
1998.04a
/
pp.31-31
/
1998
위성체의 보조추진시스템은 임구궤도까지의 궤도진입 및 임무궤도상에서의 속도 또는 자세제어에 필요한 임펄스를 제공한다. 단일하이드라진 추력기는 하이드라진(H$_2$H$_4$)과 자발적 촉매(Shell 405)의 발열 및 흡열 열분해 반응에 의해 발생하는 질소($N_2$), 수소(H$_2$), 암모니아(NH$_3$), 혼합가스를 노즐을 통해 방출하므로써 요구되는 impulse를 얻는다. 단일하이드라진 추력기 설계는 주입기, 촉매대, 노즐과 기타 설계 형태에 따른 다지관, 링, 스크린, 지지판 등의 부수적인 부품으로 구성된다. 추력기 제작 과정은 크게 piece-parts 기계가공, HEA(Head End Assembly)와 TCA(Thrust Chamber Assembly)로 구성되고 각 세부공정마다 전수시험 및 검사를 가진다. 연소시험설비는 최소 모사진 공 수준이 고도 100,000 ft(8.4 torr)를 만족시킬 수 있는 진공설비, 시험제어부, 성능변수 측정 및 처리부, 추진제 가압 공급부, 기타 환경 안전 및 부대 설비로 구성된다. 추력기 연소성능시험 절차는 추진제 충전 및 오염 여부 표본 검사, 가압 및 공급 라인 이상여부 확인, 추력기 장착, 추진제 가압 및 공급, 시험장치 보정, 진공 모사 및 연소성능시험, data 처리 등으로 구성된다.
Park, Heetae;Kim, Dongmin;Mo, Hyemin;Kim, Lamsu;Lee, Byoungju;Kim, Inrae;Kim, Seungkeun;Ryi, Jaeha;Choi, Jong-Soo
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.46
no.9
/
pp.712-722
/
2018
This paper conducts parametric studies on flapping wing design, one of the most important design parameters of insect-mimicking aerial vehicles. Experimental study on wing shape was done through comparison and analysis of thrust, pitching moment, power consumption, and thrust-to-power ratio. A two-axis balance and hall sensor measure force and moment, and flapping frequency, respectively. Wing configuration is biplane configuration which can develop clap and fling effect. A reference wing shape is a simplified dragonfly's wing and studies on aspect ratio and wing area were implemented. As a result, thrust, pitching moment, and power consumption tend to increase as aspect ratio and area increase. Also, it is found that the flapping mechanism was not normally operated when the main wing has an aspect ratio or area more than each certain value. Finally, the wing shape is determined by comparing thrust-to-power ratio of all wings satisfying the required minimum thrust. However, the stability is not secured due to moment generated by disaccord between thrust line and center of gravity. To cope with this, aerodynamic dampers are used at the top and bottom of the fuselage; then, indoor flight test was attempted for indirect performance verification of the parametric study of the main wing.
Kim, Byeong Hun;Park, Hui Ho;Hwang, Su Gwon;Kim, Yu
Journal of the Korean Society for Aeronautical & Space Sciences
/
v.31
no.4
/
pp.76-81
/
2003
To investigate the convective heat transfer phenomena inside the Lox/Kerosene liquid rocket combustion chamber, hot fire tests were performed by using a water-cooled calorimetric chamber. The calorimetric chamber consists of one cylindrical section and nozzle section with independent cooling passage. To measure the heat flux, thermocouples were installed inlet and outlet of cooling passage of each section. The investigated range of combustion chamber pressure is from 100 psi to 300psi at fixed O/F ratio of 2.0 and radiation heat transfer from the hot gas to the surface is not considered. The measured heat flux was almost linearly depended on the chamber pressure.
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2007.04a
/
pp.102-105
/
2007
The performance evaluation of the micro thruster utilizing hydrogen peroxide decomposition is described. The catalyst bed was made of porous ceramic material($Isolite^{(R)}$) with large surface to mass ratio. 14%wt platinum was loaded on the catalyst support as a catalyst. Hydrogen peroxide with 85% concentration was used as a monopropellant. The length of the catalyst bed and the feed pressure of the hydrogen peroxide were taken as the parameters for the experiment. All experiments were carried out under cold start condition for 30 seconds. The $c^*$ efficiency was evaluated for each test case using measured pressure data. For the catalyst support length of 30 mm and feed pressure at 5.51 bar, satisfactory $c^*$ efficiency beyond 95% was observed.
Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
/
v.16
no.4
/
pp.64-72
/
2002
The use of linear DC motor is spreaded according to industrial development. This study was objected to study the analysis of double side excitation LDM with moving magnet type. In this LDM structure, the mover made use of permanent magnet with six pieces so as to large thrust, the stator was bedded for the multi separated type winding to repress the i개n saturation. Also, double side excitation winding is suppressed to thrust ripple with stratification to zigzag type and designed to production for static thrust. Then it is important to ratio of permanent magnet to winding width at multi separate, this paper analyzed to separate to three pieces of 1:1, 1:0.84 and 1:0.5 with width ratio. The analysis method calculated the parameter useful for permeance and magnetic resistance more than FEM of complicated numerical value analysis. Through manufactured experiment system, measurement result of thrust was almost acquired to constant thrust for all displacement.
Kim, Su-Kyum;Yu, Myoung-Jong;Lee, Kyun-Ho;Cho, Sung-June;Lee, Jae-Won
Proceedings of the Korean Society of Propulsion Engineers Conference
/
2009.11a
/
pp.101-104
/
2009
KARI have been started development process of hydrazine decomposition catalyst for monopropellant thsuter from 2004 in cooperation with Chonnam National University and Hanwha Corps. Through the various trial and error, a catalyst that satisfies all the properties for space propulsion system was developed in 2009 and then the life firing test and qualification firing test was completed. In this paper, we will describe the development process of catalyst, the physical/chemical properties of final product and brief test results.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.