• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.288-291
• /
• 2010

Numerical analysis was conducted on thrust vector control using multi-nozzle system. The nozzle using flow valve switch to control mass flow of multi scarfed nozzle to manage thrust was considered. The operating characteristics of scarfed nozzle, thrust component and moment of multi nozzle in terms of mass flow rate were investigated by three dimensional flow simulation.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 1999.04a
• /
• pp.15-15
• /
• 1999

2차 유동 분사에 의한 추력 방향 제어 방법은 복잡한 기계적 작동장치와 이에 따른 무게의 증가를 배제할 수 있다. 본 연구에서는 유동 해석을 통하여 2차원 및 3차원 초음속 수축-팽창 노즐 유동에 2차 유동을 분사하여, 2차 유동의 분사 위치, 분사 유량 및 분사 각도 등이 추력의 방향 및 크기에 미치는 영향을 밝혀 추력 방향 제어를 위한 최적의 2차 분사 조건을 제시하였다. 유동 해석 결과 2차 유동의 분사 위치는 생성된 경가 충격파가 노즐 출구까지 분포되는 지점이 최대 전향각과 횡추력을 가지는 분사위치임을 알 수 있었고, 분사 각도는 주 유동의 역방향으로 분사하는 것이 수직방향으로 분사하는 것보다 더 큰 전향각을 얻을 수 있었다. 또한 2차원의 경우보다 3차원 유동에서 큰 전향각이 생김을 알 수 있었다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.1
• /
• pp.1-10
• /
• 2010

Design and performance evaluation of $H_2O_2$ monopropellant thrusters to be used at reaction control of space launch vehicles were presented in this paper. Design thrust level was determined as 100, 250 Newton which is nominal thrust level for commercial space launch vehicles. Qualification thruster models including solenoid valves were developed after the reactor design were evaluated at engineering thruster models. Each thruster was evaluated by measurement of characteristic velocity, thrust, specific impulse, and pulse response times at sea level test condition.

• Aerospace Engineering and Technology
• /
• v.1 no.2
• /
• pp.51-56
• /
• 2002

Satellite propulsion system is employed for orbit transfer, orbit correction, and attitude control. The monopropellant feeding system in the low-earth-orbit satellite blowdowns fuel to the thrust chamber. The thrust produced by the thruster depends on fuel amount flowed into the combustion chamber. If the thruster valve be given on-off signal from on-board commander in the satellite, valve will be opened or closed. When the thrusters fire fuel flows through opened thruster valve, instantaneous stoppage of flow in according to valve actuation produces transient pressure due to pressure wave. This paper describes transient pressure predictions of the KOMPSAT-2 propulsion system resulting from latching valve and thrust control valve operations. The time-dependent set of the fluid mass and momentum equations are calculated by MOC.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.167-171
• /
• 2012

A computational analysis of nozzle flow is conducted to investigate effects of the flight altitude on thrust performance. Reynolds-averaged Navier-Stokes equation with k-${\omega}$ SST(Shear Stress Transport) turbulence model is employed to simulate the nozzle flow in various altitude conditions, where continuum mechanics is to be valid. Thrust performance of the nozzle is exceedingly poor upto 10 km of flight altitude because of the irreversible phenomena such as shock and/or flow separation occurring inside the nozzle, whereas it is restored to the nominal value as the altitude is attained higher than 30 km.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.1-8
• /
• 1999

In the present paper an attempt has been made to simulate the secondary injection-primary flow interaction in the conical rocket nozzle and to derive the performance of secondary injection thrust vector control(SITVC) system. Complex three-dimensional flowfield induced by the secondary injection is numerically analyzed by solving unsteady three-dimensional Euler equation with Beam and Warming's implicit approximate factorization method. Emphasized in the present study is the effect of secondary injection such as secondary mass flow rates and the momentum of secondary/primary nozzle flow mass rates upon the gross system performance parameters such as thrust ratio, specific impulse ratio and deflection angle. The results obtained in terms of system performance parameters show that lower secondary mass flow rate is advantageous for to reduce secondary specific impulse loss. It is further found that the nozzle with secondary jet injected downstream and interacting with fast primary flow is preferable for efficient and stable SITVC over the wide range of use with the penalty of side specific impulse loss.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.2
• /
• pp.147-158
• /
• 2020

In this paper, we will review the thruster based reaction wheel momentum dumping method for low Earth orbit satellite. Thruster based momentum dumping is widely used in GEO satellites by performing momentum dumping and attitude control using thrusters at the specific time. LEO satellite should perform momentum dumping at any time, thus it is not appropriate to use GEO satellite's momentum dumping method. In this research, we will review the method for LEO satellite, which perform momentum dumping always and use reaction wheels for attitude control during dumping. To reduce thruster's valve on and off counts, we propose to use the maximum pulse width for thruster operation. To prevent attitude error increase by thrusters, we adjust the thruster operation interval. Through simulation, we verify the proposed method's effects.

• Aerospace Engineering and Technology
• /
• v.13 no.1
• /
• pp.44-54
• /
• 2014

This paper suggests two kinds of reaction control system command generation methods for upper stage attitude control of launch vehicles. The reaction control system is assumed to consist of two sets of three nozzles. One operation technology is based on mixed attitude error functions, and the other is based on command mixing functions. Both are compared via simulations. The simulation results show that the latter is comparatively preferable in terms of interference among control axes, independency of controller design and analysis among axes, and prediction of flight performance of each control axis.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.929-932
• /
• 2011

We developed a valve actuator controller for thruster system. This thruster system has four actuators and the actuator use a BLDC motor. Controller was made based on system and control requirement. The controller is consist of power, control and Amp. The control module use a micro-controller which is TMS320F28335 of Texas Instruments. It works for digital PID control and CAN communication and system control. The amp module for three phase BLDC motor use IGBT.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.573-577
• /
• 2009

Dynamic behavior simulation of supersonic engine was performed and PI control algorithm was studied for the buzz control in the inlet and the thrust control. Firstly, required thrust was tracked according to the fuel flow control and then inlet pressure was regulated through the nozzle throat area control so that the buzz margin has the positive all the time. The control was performed according to the change of flight Mach number, altitude and angle of attack. The proportional gain and the integral gain for regulating the buzz margin was induced and simulated. In the results, it was confirmed and satisfied that control target in the operating area was changed the angle of attack from $0^{\circ}$ to $10^{\circ}$ at the flight Mach number of 2.1~3.0.