• Journal of Aerospace System Engineering
• /
• v.16 no.4
• /
• pp.1-9
• /
• 2022

A design factor analysis was conducted to reduce the thrust reduction in the off-design, due to the driving of the aerospike pintle nozzle. The close (NPR 100) as well as the open (NPR 11) stroke were fixed, as under-expansion conditions. The pintle contour, pintle head radius (R), cowl angle (θ), and cowl exit length (L) were selected as design factors. The change in thrust was analyzed, using a verified numerical analysis technique. First, the pintle head radius and the length of the cowl exit had little influence on the thrust. The cowl angle changed the mass flow rate by affecting the effective nozzle throat area, and created a reverse pressure gradient at the cowl exit. As a result of applying the dual aerospike contour, it was confirmed that the thrust in the design-off increased by approximately 1.2%, compared to the reference case and by approximately 3.4% compared to the worst case.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.9
• /
• pp.875-882
• /
• 2011

In the present study, the imbalance in the axial-thrust and variation in the volumetric efficiency that occurred during the trimming of impeller diameter were investigated. The present study was focused on low-specific-speed multistage centrifugal pumps with a balancing piston as the balancing mechanism. The effects of impeller trimming on the axial-thrust balance in multistage pumps with horizontal and vertical axes were compared. The results showed that impeller trimming resulted in an additional axial-thrust acting in direction of pump inlet. The axial-thrust imbalance due to impeller trimming was more severe in the vertical-axis pumps than in the horizontal-axis pumps. The rate of increase in the diameter of the balancing piston, which was proportional to the rate of impeller trimming, was evaluated to maintain the axial-thrust balance. Furthermore, a simultaneous increase in the piston length and piston diameter was more effective for reducing the axial-thrust imbalance along with the volumetric efficiency drop.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.45 no.10
• /
• pp.872-880
• /
• 2017

Usually, on/off control method is a way to control the thruster. Bang-Bang Control, PWM(Pulse Width Modulator) and PWPF(Pulse Width Pulse Frequency) are widely used as a typical way. When we are designing PWPF, the incorrectly designed parameters($K_m$, ${\tau}$, $U_{on}$, $U_{off}$, $U_m$) make trouble, such as the phase lag, the wasted fuel, the reduced system life. Therefore, the effect of parameters on the system performance should be analyzed before the proper parameters are selected. In this paper, we suggest the PWPF parameters design method by performing a static analysis, and analyze the interactive effects on design parameters by performing a dynamic analysis and simulation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.10
• /
• pp.985-991
• /
• 2010

The objective of this work was to investigate the pintle-tip shape effect on nozzle flow and thrust by cold flow test. When nozzle throat area was decreased by pintle movement, chamber pressure was increased monotonously but thrust was increased differently according to every pintle-tip shape. At the same chamber pressure and nozzle throat area, thrust of convex pintle-tip shape was mostly larger than that of concave one. Nozzle wall pressure distribution and magnitude of pintle-tip load depended on the pintle-tip shape, pintle position and nozzle throat area.

• Journal of Astronomy and Space Sciences
• /
• v.15 no.1
• /
• pp.221-228
• /
• 1998

The effect of air drag was researched when a low-earth orbit spacecraft using power-limited thruster rendezvoused another low-earth orbit spacecraft. The air density was assumed to decrease exponentially. The radius of parking orbit was 6655.935km and that of target orbit was 7321.529km. From the trajectories of active vehicles, the fuelconsumption and the magnitude of thrust acceleration, we could conclude that the effect of air drag had to be considered in fuel optimal rendezvous problem between low-earth orbit spacecrafts. In multiple-revolution rendezvous case, the air drag was more effective.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.269-272
• /
• 2009

Catalytic decomposition of nitrous oxide was investigated experimentally. Two noble metal catalyst (Pt, Ir) were chosen to decompose nitrous oxide. Each catalyst was tested with different chamber pressure and preheating temperature. Ir decomposed $N_2O$ at lower temperature ($230^{\circ}C$) and suitable for $N_2O$ decomposition. In addition, the minimum required preheating temperature decreased as the chamber pressure increased. However, deactivation of Ir catalyst was observed during the experiments.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.12 no.5
• /
• pp.9-17
• /
• 2008

Pseudo-3D spatial distribution of spray droplets is investigated by using Dual-mode Phase Doppler Anemometry (DPDA) in order to examine the disintegration and spreading behavior of spray exiting from liquid-propellant thruster injector. Spray injected from nozzle orifice with length-to-diameter ratio ($L/d_o$) of 1.67 and under the injection pressure of 27.6 bar is aligned to the vertical. Vertical and horizontal mean velocities of droplets, Sauter Mean Diameter (SMD), and volumetric flux decrease as droplets travel from center/upstream toward outer region/downstream of spray. Although the distribution of spray characteristic parameters is symmetric against the geometric axis of nozzle orifice, their absolute values are asymmetric.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.11a
• /
• pp.113-116
• /
• 2008

Pseudo-3D Spatial distribution of spray droplets is investigated by using Dual-mode Phase Doppler Anemometry (DPDA) in order to examine the disintegration and spreading behavior of spray exiting from liquid-thruster injector. Spray injected from nozzle orifice with length-to-diameter ratio $(L/d_o)$ of 1.67 and at the injection pressure of 27.6 bar is aligned to the vertical. Vertical and horizontal mean velocities of droplets, Arithmetic Mean Diameter (AMD), Sauter Mean Diameter (SMD), and volumetric flux decrease as droplets travel from center/upstream toward outer region/downstream of spray.

• Journal of Advanced Marine Engineering and Technology
• /
• v.41 no.1
• /
• pp.36-43
• /
• 2017

The results of a numerical study on the performance of a propeller operating near a free surface are presented in this paper. The simulations are verified through comparison with experimental data, which was performed in a circulating water channel. The propeller performance as a function of the submerged depth was investigated. The effect of the propeller advance ratio on the wave patterns, flow structures around propeller, and thrust and torque of the propeller was also studied. Air ventilation was not observed for low advance coefficients. However, the simulations showed that wave pattern was strongly related to the tip vortex strength and inflow velocity. When air ventilation does not occur, the deduction of propeller thrust and torque increase for high advance coefficients.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.2
• /
• pp.95-105
• /
• 2018

Increasing cruise speed is an important issue for the development of the next generation rotorcraft. Among several concepts proposed by previous research, the rotorcraft with ducted fan demonstrates its possibility of high-speed flight. In this study, numerical simulations are conducted to investigate the aerodynamic and flow characteristics of multi-ducted fan in forward flight. The aerodynamic efficiency around front ducted fan is determined by interaction between free-stream velocity and the induced velocity. While flow characteristics of rear ducted fan are dominantly influenced by the front ducted fan. Separation in the front ducted fan occurs faster than that of rear ducted fan, and the separation at duct inlet induces an increase of fan thrust. As a result of interaction effect between each ducted fan, relatively aligned inflow enters to the rear ducted fan. Therefore, thrust of the rear fan is decreased steadily before separation, and sudden changes of thrust in fans occur simultaneously. Due to the pressure decrease on lower surface, the normal force of rotorcraft is reduced with forward speed.