• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2003년도 춘계학술발표대회 요약집
• /
• pp.258.1-258.1
• /
• 2003

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2002년도 추계학술발표회요약집
• /
• pp.288.2-288
• /
• 2002

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2004년도 요약집 춘계학술발표대회
• /
• pp.300.1-300.1
• /
• 2004

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2005년도 창립60주년 기념 추계 학술대회
• /
• pp.173.1-173.1
• /
• 2005

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1803-1806
• /
• 2007

The General roles of a spacer grid(SG) are providing a lateral and vertical support for fuel rods, promoting a mixing of coolant and keeping guide tubes straight so as not to impede a control rod insertion under any normal or accidental conditions. To evaluate the impact characteristics of a SG such as impact velocity, critical buckling strength and duration time, a few types of impact tests for SGs have been conducted. In a previous study, a new welding method, a through-welding method, was proposed to increase critical buckling strength of a SG without any design change or material change and was verified by impact tests with $7{\times}7$ partial SG specimens.In this paper, the effect of through-welding method in case of a $16{\times}16$ full-size SG is investigated by pendulum impact tests with $16{\times}16$ SG specimens. And the increase of critical buckling strength for full-size SGs is measured by comparison with impact results of spot-welded and through-welded SGs.

• 대한안전경영과학회지
• /
• 제13권4호
• /
• pp.213-223
• /
• 2011

Recent cross-country competition and Chinese steel industry because of the emerging steel industry in Korea is a very difficult situation. Therefore, the steel industry in order to overcome this difficult market environment, the quality, cost competitiveness, enhance customer service levels and enhance international competitiveness through is needed. In this study, the purpose of strengthening the competitiveness of steel companies in order and hit the recovery of raw materials have been developed to optimize the model, developed before and after the results were analyzed. In addition, when applied to other products in order to minimize risk and optimize cutting trial stage of development details of the model is presented in detail. Therefore, the developed model was applied to order the recovery of raw materials hits and significantly improved production planning time has been shortened dramatically. In the present study the contents of other products when properly applied and the competitiveness of companies to improve customer service levels are expected to be helpful.

• 한국소음진동공학회논문집
• /
• 제14권6호
• /
• pp.512-519
• /
• 2004

This paper described the free vibration characteristics of Optimized H Type (OHT) spacer grids (SG) supporting the PWR fuel rod. The vibration test and the finite element (FE) analysis are performed under the free boundary condition and the clamped at two points (or three points) in the bottom which is the same one as the experimental condition for the dummy rod continuously supported by spacer grids. A modal test is conducted by the impulse excitation method using an impulse hammer and an accelerometer, and the TDAS module of the I-DEAS software is used to acquire and analyze the sensor signals. The softwares related to the FE analysis are the I-DEAS for the geometrical shape modeling and meshing, and the ABAQUS for solving. The fundamental frequency of the OHT SG by experiment under a clamped condition at two points is 175.18 Hz, and shows a bending mode. We think there is no resonance between the fuel rod and the SG because the SG's frequency is higher than that of the fuel rod existing in the range from 30 to 120 Hz. The fundamental frequency of the SG under the free boundary condition is 349.2 Hz showing a bending mode, and the results between the test and the analysis have a good agreement with maximum 7 ％ in error It is also found that the FE analysis model of the OHT SGs to analyze an impact, a buckling and vibration et al. has been generated with reliability.

• 한국강구조학회 논문집
• /
• 제19권5호
• /
• pp.483-492
• /
• 2007

최근 대형 장스팬 규모에 많이 적용되는 PEB 시스템은 휨모멘트의 크기에 따라 부재형상을 최적화 한 변단면부재를 사용함으로써 경제적인 경쟁력을 갖는 구조시스템이다. 그러나 PEB 시스템의 관련기술은 대부분 외국에서 수입된 것으로 구조거동에 관한 연구 및 국내 설계규준이 미비하다. 특히 PEB 시스템에서의 변단면부재(래프터)들은 비조밀단면(noncompact section) 또는 세장단면(slender section)을 갖는 경우가 많으므로 좌굴에 대한 영향을 많이 받게 된다. 따라서 본 연구에서는 웨브의 판폭두께비, 스티프너 유무, 횡비지지길이 등을 변수로 하여 총 4개의 실대형 실험체를 제작 휨성능 실험을 수행하였다. 이에 대하여 세장한 웨브 변단면 부재의 구조 안정성을 실험적으로 평가하고 PEB 시스템의 설계를 위한 기초자료를 제공하고자 한다.