• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.10
• /
• pp.769-778
• /
• 2017

In this paper, a self-interference signal cancellation(SIC) circult for In-band Full-Duplex has been developed and tested in RF/analog region. By use of this SIC circuit, a FM two-way radio has been developed working at FRS(Family Radio Service) band. The two-way radio device is transmitting the FM modulated signal and demodulating the wanted FM signal at the same time. A circulator is used to enable a single antenna to transmit and receive simuultaenously. The receiver circuit needs to cancel out the self-interference signal due to the transmit signal. A vector modulator(VM) is used to control the phase and magnitude of the esitmated signal. And in-phase and quadrature correlators are used to figure out the optimal coefficients of the VM to remove the self-interference signal according to the change of channel environment. In this work, SA58646 has been used as the FM transceiver, and the system is tested with a frequency of 465 MHz and a bandwidth of 12.5 kHz FM signal. The output power is 17.2 dBm at the antenna port, and the self intererence signal level is measured -49.2 dBm at the receiver end. Therefore the SIC level is measured by 66.4 dB.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.529-535
• /
• 2018

The range extender vehicle runs on a mechanism that allows the small power generation engine to start in the most efficient specific operating range to charge the battery and extend the mileage. In this study, we developed a step motor type intake air supply system that replaces existing throttle body system to develop a simple low cost control logic system. The system was applied to the existing base engine, and in order to improve the performance by increasing the amount of intake air, the effect of changing the length of the intake and exhaust manifold was experimentally examined. As a result, the Type B intake air control actuator operated by one step motor showed higher performance than the Type A in all the operation region, but the performance was lower than that of the base engine due to the increase of flow resistance. To improve this, it was confirmed that the engine performance was improved at both speeds of 2200rpm and 4300rpm when the 140mm adapter was installed in the intake manifold and when the newly designed 70mm exhaust manifold was applied. Through this process, high - precision operation control was realized by connecting the generator load to the optimized engine for the range extender electric vehicle. Experimental results showed that the speed change rate was within ${\pm}2.5%$ at 2200rpm in 1st stage and 4300rpm in 2nd stage and the speed follow-up result of 610 rpm/s was obtained when the speed was increased from 2200rpm to 4300rpm.

• Fire Science and Engineering
• /
• v.26 no.1
• /
• pp.23-30
• /
• 2012

The temperature development of a structural element is dependent on section factor, which is estimated as a ratio of the fire-exposed perimeter to the cross-section area. Hence, with the higher section factor, the faster temperature development of the section os observed. Composite beam member, partially embedded asymmetry H beam, has a good fire resistance to the cross-section. The study was intended to conduct with change with section factor. The experimental result of section type which the Slim Beam Floor is bottom flange reinforced method.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.8 no.8
• /
• pp.1219-1226
• /
• 2013

This study is the analysis and verification process of the L-band satellite communications repeater thought PCB & circuit EM analysis. System performance can be vulnerable to various spurious inside the L-band satellite transponder, power conversion board, digital signal board, TM/TC board, such as control panels and blocks that are linked signal components when the winch is increased due to the noise component. So the whole system can cause performance degradation. PCB resonance analysis and EM simulation can be easily analyzed for a variety of optimal. Also, by setting the ports on the PCB, H/W designer wants to can easily analyze system.

• Journal of KSNVE
• /
• v.8 no.2
• /
• pp.267-273
• /
• 1998

This study aims at performing sensitivity analysis of piezoelectric smart structure for minimizing radiated noise from the structure, The structure consists of a flat plate on which disk shaped piezoelectric actuator is mounted, and finite element modeling is used for the structure. The finite element modeling uses a combination of three dimensional piezoelectric, flat shell and transition elements so thus it can take into account the coupling effects of the piezoelectric device precisely and it can also reduce the degrees of freedom of the finite element model. Electric potential on the piezoelectric actuator is taken as a design variable and total radiated power of the structure is chosen as an objective function. The objective function can be represented as Rayleigh's integral equation and is a function of normal displacements of the structure. For the convenience of computation, all degrees of freedom of the finite element equation is condensed out except the normal displacements of the structure. To perform the design sensitivity analysis, the derivative of the objective function with respect to the normal displacements is found, and the derivative of the norma displacements with respect to the design variable is calculated from the finite element equation by using so called the adjoint variable method. The analysis results are compared with those of the finite difference method, and shows a good agreement. This sensitivity analysis is faster and more accurate than the finite difference method. Once the sensitivity analysis program is used for gradient-based optimizations, one could achieve a better convergence rate than non-derivative methods for optimal design of piezoelectric smart structures.

• Journal of Satellite, Information and Communications
• /
• v.10 no.4
• /
• pp.1-5
• /
• 2015

The ESD(electrostatic discharge) protection performance of PPS(PMOS pass structure) embedded N-type silicon controlled rectifier(NSCR_PPS) device with different partial p-well(PPW) structure was discussed for high voltage I/O applications. A conventional NSCR_PPS standard device shows typical SCR-like characteristics with low on-resistance, low snapback holding voltage and low thermal breakdown voltage, which may cause latch-up problem during normal operation. However, our proposed NSCR_PPS devices with modified PPW_PGM(primary gate middle) and optimal CPS(counter pocket source) implant demonstrate the stable ESD protection performance with high latch-up immunity.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.2
• /
• pp.141-149
• /
• 2010

This paper contains impulsive maneuver which considers fuel consumption balance of chief satellite and deputy satellite in satellite formation flying. Thrust input is obtained by Lagrange' Multiplier method which is constructed by cost function with weight parameter of each satellite. Energy matching constraint is applied for boundedness of relative orbit, and theoretical solutions are verified by simulation results. Simulations are divided into two scenarios, with or without air-drag effect. This paper's results are expected to be used in real satellite formation flying, when fuel-balancing impulsive maneuver for relative orbit boundedness is needed.

• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.669-675
• /
• 2009

A study has been made on the preparation of liquid resin of non-solvent and non-discoloration type for replacement of the soft PVC at room temperature. A new synthetic process was developed by structure-control design of polyurethane synthesis using pre-polymer and polyols as curing agent. The optimum recipe was made according to macro-glycols, molecular weight and reaction conditions, and the final products indicated that the mechanical properties such as tensile strength, tear strength and flexibility was very excellent than PVC products. Also, viscosity, hardness and color operations of the final products can be controlled by this system. And yellowing property by UV and NOx gas was improved from the various additive experiment.

• Information and Communications Magazine
• /
• v.33 no.1
• /
• pp.42-47
• /
• 2015

본고에서는 개인 또는 기업이 아이디어를 제품화하는 과정에서 겪게 되는 생산진입의 어려움을 해소하기 위해서 개인맞춤생산을 지원하는 개방형 제조서비스 플랫폼 (FaaS: Factory as a Service)을 제안한다. FaaS 플랫폼은 다양한 고객들의 맞춤형 제품에 대한 요구를 수용하여 가능한 대량 생산에 가까운 효율로 생산하도록 설계하였으며, 개인맞춤생산을 위한 스마트 제조기술과 제조서비스 플랫폼 기능을 제공한다. FaaS 플랫폼은 고객이 자신이 원하는 제품생산의 요구를 정확하게 지속적으로 전달하기 위해 개방성을 제공하는 FaaS 클라우드 계층과 다양한 이종 제품들을 최적의 생산 효율을 가지고 혼류생산 할 수 있도록 하는 FaaS 제조운영 계층, 그리고 3D프린터, 로봇과 같은 혁신형의 제조설비들을 IoT(Internet of Things)를 기반으로 유기적으로 연결함으로써 팩토리 전체 성능을 향상시키도록 하는 FaaS 실행제어 계층으로 구성된다. 본 고에서 제안한 FaaS 플랫폼은 향후 기술개발 결과물을 실 수요 제품을 생산하는 ICT융합형 제조서비스 스마트팩토리 실증테스트베드에 적용하여 시범운영을 통해 기술을 검증하고 확장할 계획으로 있으며, 이를 통해 창업 기업이나 중소 제조기업들이 신제품의 시장진입시간을 단축시키고, 실질적인 펀딩 효과를 가질 수 있기를 기대한다.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.2 no.3
• /
• pp.1-5
• /
• 2005

There are two types of solenoid actuator for force and position control of the fluid power system. One is an on-off solenoid actuator and the other is an electro-magnetic proportional actuator. They have some different characteristics for attraction force according to solenoid shape. Attraction force of the on-off solenoid actuator only depends on flux density. And the stroke-force characteristics of the proportional solenoid actuator are determined by the shape of the control cone. In this paper, steady state characteristics of the solenoid actuator for electro-hydraulic proportional valve determined by the shape of control cone are analyzed using finite element method and it is confirmed that the proportional solenoid actuator has a constant attractive force in the control region independently on the stroke position. And the shape of control cone is optimized using 1+1 evolution strategy to get a constant force. In the optimization algorithm, control cone length, thickness and taper length are used as a design parameter.