• Korean Journal of Optics and Photonics
• /
• v.4 no.1
• /
• pp.47-56
• /
• 1993

Practical efficiencies of pulsed gas discharge lasers utilizing vaporized Au, Ba, Cu, Fe, Mn, Pb, TI atoms are numerically optimized for a discharge pulse of 30 ns rise time at 5 kHz pulse repetition rate. Calculated optimum operating temperatures are close to the values at which the vapor pressure of each atom is about 1 Torr and are in good agreement with experimental values reported elasewhere. The optimum charging voltage was about 4 kV for all atomic vapor lasers except the TI laser. The calculated maximum efficiencies that have been discussed for possible limiting efficiencies for each laser were considerably higher than the reported experimental values. Especially, they were as high as 6.8% for Mn laser and 15% for Ba laser that were comparable to the 8.5% of copper vapor laser, from which considerably higher efficiencies can be expected for these two lasers experimentally. But, the present calculation shows a very low efficiency of 0.058% and requires an exceptional operating condition for the TI laser.

• Applied Biological Chemistry
• /
• v.37 no.2
• /
• pp.130-141
• /
• 1994

A continuous two-stage membrane (1st-SCMR, MWCO 10,000; 2nd-SCMR, MWCO 5,000) reactor was developed and optimized for the production of fish skin gelatin hydrolysate with different molecular size distribution profiles using trypsin and pronase E. The optimum operating conditions in the 1st-step membrane reactor using trypsin were: temperature, $55^{\circ}C$ ; pH 9.0; enzyme concentration, 0.1 mg/ml; flux, 6.14 ml/min; reaction volume, 600 ml; and the ratio of substrate to trypsin, 100 (w/w). After operating for 1 hr under the above conditions, 79% of total amount of initial gelatin was hydrolysed. In the 2nd-step using pronase E under optimum operating conditions[temperature, $50^{\circ}C$ ; pH 8.0; enzyme concentration, 0.3 mg/ml; flux, 6.14 ml/min; reaction volume, 600 ml; and the ratio of substrate to pronase E, 33 (w/w)], the 1st-step hydrolysate was hydrolysed above 80%. Total enzyme leakages in the 1st-step and 2nd-step membrane reactors were about 11.5% at $55^{\circ}C$ for 5hrs and 9.0% at $50^{\circ}C$ for 4 hrs, respectively. However, there was no apparent correlation between enzyme leakage and substrate hydrolysis. The membrane has a significant effect on activity lose of trypsin and pronase E activity for 1 hr of the membrane reactors operation. The loss of initial activity of enzymes were 34% and 18% in the 1st-step and 2nd-step membrane reactor, whereas were 23% and 10% after operating time 3 hr in the 1st-step and 2nd-step membrane reactor lacking the membrane, respectively. The productivities of 1st-step and 2nd-step membrane reactor for 8 times of volume replacement were 334 mg and 250 mg per mg enzyme, respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.304-304
• /
• 2011

열필라멘트 화학 기상 증착 공정(HWCVD, hot wire chemical deposition)은 낮은 기판 온도에서 다결정 실리콘 박막을 빠른 속도로 증착할 수 있는 방법이다. 이는 후처리가 없어도 전기적 특성이 우수한 박막을 저온에서 얻을 수 있기 때문에 녹는점이 낮은 기판에 증착을 할 수 있으며 공정비용 절감 효과가 있다. 이러한 박막 증착 공정 중 기상 핵생성에 의해 나노 입자가 생성되며, 새로운 관점에서는 그 농도와 크기가 박막 성장에 중요한 변수로 작용한다. 따라서 공정조건의 변화에 따라 생성되는 나노 입자의 크기 분포를 실시간으로 분석하여 박막 형성의 최적 조건을 찾는 연구가 필요하다. 하지만 이러한 입자 발생 특성에 관한 연구는 기존에 밝혀진 반응 메커니즘으로 인해 수치해석적 연구는 체계적으로 진행되었으나 실험적 연구의 경우 적합한 측정장비의 부재로 인해 제한이 있었다. 따라서 본 연구에서는 저압에서 실시간으로 나노입자 분포를 측정할 수 있는 PBMS (particle beam mass spectrometer)를 이용하여 열필라멘트 화학 기상 증착 공정 중 발생하는 입자의 존재를 확인하고 특성을 분석하였다. 실리콘 나노 입자의 측정은 PBMS 장비의 전단 부분을 HWCVD 배기 라인에 연결하여 진행하였으며 반응기 내 샘플링 위치, 필라멘트 온도, 챔버 압력, 작동기체의 비율을 변수로 하여 진행하였다. 그 결과 실리콘 나노 입자는 양 또는 음의 극성을 가진 하전된 상태임을 확인 하였고, 측정 조건에 따라 일부 단일 극성으로 존재하였다. 한편, 필라멘트 온도가 증가할수록 하전된 나노입자의 최빈값은 감소하였다. 또한 반응 가스인 SiH4 농도가 증가할수록 최빈값은 농도에 비례하여 증가하였다. 이런 결과는 기존 HWCVD 실험에서 투과 전자 현미경(TEM)을 이용하여 분석한 실리콘 나노 입자의 크기 분포 결과와 경향이 일치함을 확인하였다. 본 연구를 통하여 확인된 하전된 나노 입자의 존재를 실험적으로 확인하였으며 추후 지속적 연구에 의해 이러한 하전된 나노 입자가 박막 형성에 기여 하는 것을 규명하고 박막 형성 조건을 최적화하는데 중요한 역할을 할 것을 기대할 수 있다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.8
• /
• pp.737-743
• /
• 2009

Design optimization process and results of Loop Heat Pipe(LHP) using Tabu Search have been presented in this study. An objective of optimization is to reduce a mass of the LHP with satisfying operating temperature of a Lithium Ion battery onboard an aircraft. The battery is assumed to be used as power supply of air borne high energy laser system because of its high specific energy. The analytical models are based on a steady state mathematical model and the design optimization is performed using a Meta Model and Tabu Search. As an optimization results, the Tabu search algorithm guarantees global optimum with small computation time. Due to searching by random numbers, initial value is dominant factor to search global optimum. The optimization process could reduce the mass of the LHP which express the same performance as an published LHP.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.3
• /
• pp.66-73
• /
• 2004

As a rocket propellent of hydrocarbon fuels, the characteristics of liquefied natural gas was evaluated with the viewpoint of the constituents and content, the cooling performance as a coolant, and characteristic velocity and specific impulse as parameters of the engine performance. Content of methane was a principal factor to determine the characteristics as a rocket propellant and more than 90% of it was needed as a fuel and coolant in the regenerative cooled liquid rocket engine. Some constituents of the liquefied natural gas can be frozen by the pre-cooling of the pipe lines, therefore they can be a factor disturbing the normal working of engine. In case the content of methane is around 90% in the liquefied natural gas, a normalized stoichiometric O/F mixture ratio of 0.75 is suggested for a nominal operation condition to get the maximum specific impulse and characteristic velocity.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.2545-2552
• /
• 2014

This study is aiming to suggest the effective thermal management system design technologies for the high voltage and capacity battery system of the electricity driven vehicles and introduce the theoretical designing methods. In order to investigate the effective operation of the battery system for the electricity driven vehicles, the heat generation model for Li-ion battery system using the chemical reaction while charging and discharging was suggested and the thermal loads of the heat sources (air or liquid) for cooling and heating were calculated using energy balance. Especially, the design methods for the cooling and heating of the battery system for maintaining the optimum operation temperature were investigated under heating, cooling and generated heat (during charging and discharging) conditions. The battery thermal management system for the effective battery operation of the electricity driven vehicles was suggested reasonably depending on the variation of the season and operation conditions. In addition, at the same conditions under summer season, the cooling method using the liquid and active cooling technique showed a relatively high capacity, while cooling method using the passive cooling technique showed a relatively low capacity.

• Applied Chemistry for Engineering
• /
• v.5 no.4
• /
• pp.681-697
• /
• 1994

The enzymatic hydrolysate of gelatin extracted from fish skin was fractionated and recycled through the membrane reactor according to the molecular weight for the purpose of using as functional material. In addition, the enzymatic hydrolysis conditions of gelatin, enzyme stability by membrane and mechanical shear, and effect on the long-term operational stability of the recycle membrane reactor were investigated. Using the pH-drop technique, Alcalase, pronase E and collagenase were identified as the most suitable enzymes for the hydrolysis of fish skin gelatin. The optimum hydrolysis conditions in the 1st-step membrane reactor(1st-SMR) by Alcalase were enzyme concentration 0.2mg/ml, substrate-to-enzyme ratio(S/E) 50(w/w), $50^{\circ}C$, pH 8.0, reaction volume 600ml and flow rate 6.14ml/min. In the 2nd-SMR by pronase E were enzyme concentration 0.3mg/ml, S/E 33(w/w), $50^{\circ}C$, pH 8.0, reaction volume 600ml and flow rate 6.14ml/min. In the case of 3rd-SMR, enzyme concentration 0.1mg/ml, S/E 100(w/w), $37^{\circ}C$, pH 7.5, reaction volume 600ml and flow rate 10ml/min. Decreased enzyme activities by mechanical shear and membrane were 30% and 15% in the 1st-SMR, were 14% and 5% in the 2nd-SMR, and 18% and 8% in the 3rd-SMR, respectively. Under the optimum conditions, the degree of hydrolysis in the 1st, 2nd and 3rd-SMR were 3.5%(Kjeldahl method, 87%), 3.1%(77%) and 2.7%(70%), respectively. The productivity of hydrolysate in the continuous three-step membrane reactor was 430mg per enzyme(mg) for 10 times of volume replacements.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.8
• /
• pp.797-806
• /
• 2008

In a double-passage cascade apparatus, only two blades are installed in order to increase the accuracy of experimental result by applying bigger blade than the size of multi-blades on the same apparatus. However, this causes difficulties to make correct periodic condition. In this study, sidewalls are designed to meet periodic condition without removing the operating fluid or adjusting tail boards. Surface Mach number on the blade surface is applied to a responsible variable, and 12 design variables which are related with sidewall profile control are selected. A gradient-based optimization is adopted for wall design and CFX-11 is used for the internal flow computation. The computed result shows that it could obtain the same flow structure by modifying only the sidewalls of the double-passage cascade apparatus.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.276.1-276.1
• /
• 2016

본 연구에서는 차세대 유연 투명 히터 (Flexible and transparent heater) 제작을 위한 ATO 나노입자-은 네트워크 하이브리드 투명 전극의 특성을 연구하였다. 최적화된 은 네트워크 (Self-assembled Ag network) 투명 전극 상에 20-30 nm의 직경을 가지는 ATO (Sb-doped $SnO_2$) 나노입자를 스프레이 방식으로 상압, 상온에서 코팅하여 인쇄형 ATO-은 네트워크 하이브리드 투명 전극을 구현하였다. 스프레이로 코팅된 투명 ATO 나노 입자는 은 네트워크 전극의 빈 공간을 매워 줌으로써 은 네트워크 간의 연결성 및 표면 조도를 낮춰주어 유연 투명 히터 작동 시 전류의 집중 현상을 막아줄 수 있다. ATO-은 네트워크 하이브리드 투명 전극의 최적화를 위해 스프레이 횟수에 따른 하이브리드 투명 전극의 전기적, 광학적, 표면 특성을 분석하였으며, 최적의 조건에서 14 Ohm/square의 면저항과 66%의 투과도를 가지는 하이브리드 투명 전극을 구현하였다. 또한 FESEM 분석을 통해 ATO-은 네트워크 하이브리드 전극의 표면 및 계면 구조를 연구하고 ATO 코팅이 은 네트워크 전극의 특성에 미치는 영향을 규명하였다. 최적화된 ATO-은 네트워크 하이브리드 투명 전극을 이용하여 유연 투명 히터를 제작하고 전압에 따른 히터의 온도의 변화를 측정하여 차세대 유연 투명 히터용 투명 전극으로 인쇄기반 ATO-은 네트워크 하이브리드 투명 전극의 가능성을 확인하였다.

• Journal of Korea Society of Industrial Information Systems
• /
• v.7 no.3
• /
• pp.54-61
• /
• 2002

A remote image transmission apparatus combines robot technology and image transmission there is safe problem or place that a person can not go. Recently, control apparatus that use wire and RF between web server and robot for remote control are developed. But there is problem that must install internet line and communication distance. Transmission distance problem call solve when using the equipment of RF, but price of RF router is problem that is very high cost. In this paper, we developed remote control system using the CDMA cellular phone communication network that can control image transmission and image transmission apparatus to solve these problem. Developed system could solve defects of methods that use existent RF and internet. And could transmit the most suitable image and voice under limited condition include current communication network.