• The Korean Journal of Food And Nutrition
• /
• v.26 no.1
• /
• pp.29-34
• /
• 2013

The objective of this study was to manufacture three kinds of domestic sweet potato Makgeolli using a mixture design and an optimization technique. The effects of four different manufacture methods, such as simultaneous saccharification and fermentation (SSF) with or without malt and separate hydrolysis and fermentation (SHF) with or without malt were determined. The SSF methods of Makgeolli produced higher alcohol content than that of SHF methods. The sensory score was not influenced by different making methods. Fourteen experimental points were selected, and rice (10~50%), sweet potato (10~50%) and water (40~60%) were chosen as independent variables. The measured responses were sensory preference, total polyphenol content, and DPPH radical scavenging activities. The ratio of the optimum sweet potato Makgeolli mixture formulation was developed as 15.11 (rice): 44.89 (sweet potato): 40 (water) using the optimization technique. The desirability of the optimum mixture formulation was 0.839. Yellow sweet potato Makgeolli using the optimum mixture formulation produced higher soluble sugar content compared to others. Regular sweet potato Makgeolli produced higher pH. The purple sweet potato Makgeolli's total polyphenol content and DPPH radical scavenging activity were measured to be the highest at $771.91{\pm}1.42mg\;GAE/{\ell}$, $131.55{\pm}4.03%$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.10
• /
• pp.4832-4836
• /
• 2012

In general, there are needed lots of time and experiments for determination of optimum asphalt content and mix design. The experimental results are highly depended on the skill of testers. Bailey suggested the proper aggregate gradation of hot mix asphalt are a function of special size and passing percent of the specified aggregate to reduce the test errors. In this paper, the asphalt mix designs of 19mm dense graded mix and PA-20mm for FHWA were carried out, using Bailey's method. The use of Bailey method can cut down the testing times to get the proper aggregate gradation for asphalt mix design. In case of 19mm dense graded asphalt mixture, the measured values of CA, $FA_c$, $FA_f$ are 0.724, 0.440, and 0.455, which are within the suggested values by Bailey. Also, in case of PA-20 graded asphalt mixture, the measured values of CA, $FA_c$, $FA_f$ are 0.646, 0.476, and 0.450, respectively.

• Journal of the Korea Concrete Institute
• /
• v.23 no.1
• /
• pp.99-107
• /
• 2011

This study is to performed to find the optimum mix proportion of the high strength and self compacting concrete for the above-ground LNG storage tank construction and field application. If LNG storage tank wall thicknesscan be reduced, the construction cost and quality can be improved by using self-compacting high strength concrete with compressive strength 60~80 MPa. For this purpose, low heat cement (Type IV) and class F fly ash are used in concrete mix to control hydration heat, flowability, and viscosity. Mix design variables of unit water, fly ash replacement ratio, water-binder ratio, and fine aggregate ratio are selected and tested for material properties and manufacturing cost of the concrete. Also, fly ash replacement ratio is considered using confined water ratio test. The test results showed that the optimum mix proportion of the self-compacting high strength concrete characteristics are as follows. 1) In case of the concrete with specified compressive strength of 60 MPa, the optimum mix proportion is fly ash replacement ratio of 20% and water- binder ratio of 27~30%. 2) In case of the concrete with the strength of 80 MPa, the optimum mix proportion is fly ash replacement ratio of 10% and water-binder ratio 25%. But unit water and fine aggregate ratio are 165 $kg/m^3$ and $51{\pm}2%$, respectively, regardless of the traget concrete compressive strength range. Also, test results showed that concrete manufacturing cost of 60 MPa and 80 MPa concrete require additional costs of 14~22% and 33%, respectively, compared to the manufacturing cost of 40 MPa concrete. Therefore, application of the self-compacting high strength concrete has proven to be economical in the perspective of the material cost, quality control, and site management.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.5
• /
• pp.92-103
• /
• 2015

Box-Wilson experimental design method, known as central composite design, is the design of any information-gathering exercises where variation is present. This method was devised to gather as much data as possible in spite of the low design cost. This method was employed to model the effect of mixing factors on several performances of 60 MPa high strength self compacting concrete and to numerically calculate the optimal mix proportion. The nonlinear relations between factors and responses of HSSCC were approximated in the form of second order polynomial equation. In order to characterize five performances like compressive strength, passing ability, segregation resistance, manufacturing cost and density depending on five factors like water-binder ratio, cement content, fine aggregate percentage, fly ash content and superplasticizer content, the experiments were made at the total 52 experimental points composed of 32 factorial points, 10 axial points and 10 center points. The study results showed that Box-Wilson experimental design was really effective in designing the experiments and analyzing the relation between factor and response.

• Journal of the Korea Concrete Institute
• /
• v.22 no.3
• /
• pp.335-343
• /
• 2010

Steel corrosion in reinforced concrete (RC) structures is a critical problem to structural safety and many researches are being actively conducted on developing methods to maintain the required performance of the RC structures during their intended service lives. In this study, concrete mixture proportioning technique through genetic algorithm (GA) for RC structures under carbonation, which is considered to be serious in underground site and big cities, is investigated. For this, mixture proportions and diffusion coefficients of $CO_2$ from the previous researches were analyzed and fitness function for $CO_2$ diffusion coefficient was derived through regression analysis. This function based on the 12 experimental results consisted of 5 variables including water-cement ratio (W/C), cement content, sand percentage, coarse aggregate content per unit volume of concrete in unit, and relative humidity. Through genetic algorithm (GA) technique, simulated mixture proportions were proposed for 3 cases of verification and they showed reasonable results with less than relative error of 10%. Finally, assuming intended service life, different exposure conditions, design parameters, intended $CO_2$ diffusion coefficients, and cement contents were determined and related mixture proportions were simulated. This proposed technique is capable of suggesting reasonable mix proportions and can be modified based on experimental data which consider various mixing components like mineral admixtures.

• Journal of the Korean Geosynthetics Society
• /
• v.14 no.3
• /
• pp.13-20
• /
• 2015

Inappropriate backfill material and poor compaction cause the damage to sewer and ground settlement. To deal with such problem, flowable backfill material has attracted attention recently. A basic study was conducted in a bid to obtain optimum mixing ratio of backfill material with the characteristics of rapid hardening, pseudo-plasticity, flowability and anti washout ability and enhance the cost efficiency of backfill material. Through the test of optimal mixing ratio of rapid hardening, evaluation of optimal mixing ratio of backfill material was conducted. As a result, required performance as well as cost efficiency could be achieved by adjusting plasticizer even in case of increasing W/M of the paste of rapid hardening to 100%.

• Journal of the Korea Concrete Institute
• /
• v.27 no.4
• /
• pp.419-426
• /
• 2015

The purpose of this study is to investigate experimentally the optimum mix design and site application case of soil mixing wall (SMW) method which is cost-effective technique for construction of walls for cutoff wall and excavation support as well as for ground improvement before constructing LNG storage tank typed under-ground. Considering native soil condition in site, main materials are selected ordinary portland cement, bentonite as a binder slurry and also it is applied $1,833kg/m^3$ as an unit volume weight of native soil, Variations for soil mixing wall are as followings ; (1) water-cement ratio 4cases (2) mixing velocity (rpm) 3levels (3) bleeding capacity and ratio, compressive strength in laboratory and site application test. As test results, bleeding capacity and ratio are decreased in case of decreasing water-cement ratio and increasing mixing velocity. Required compressive strength (1.5 MPa) considering safety factors in site is satisfied with the range of water-cement ratio 150% below, and test results of core strength are higher than those of specimen strength in the range of 8~23% by actual application of element members including outside and inside in site construction work. Therefore, optimum mix design of soil mixing wall is proposed in the range of unit cement $280kg/m^3$, unit bentonite $10kg/m^3$, water-cement ratio 150% and mixing velocity 90rpm and test results of site application case are satisfied with the required properties.

• Composites Research
• /
• v.27 no.4
• /
• pp.168-173
• /
• 2014

The optimum condition of glass fiber/epoxy composites was investigated according to mixing ratio of two epoxy matrices. Novolac type epoxy and isocyanate modified epoxy were used as composites matrix. Based on chemical composition of mixing matrix, optimum mixing ratio of epoxy resins was obtained through various experiments. In order to investigate thermal stability and interface of epoxy resin, glass transition temperature was observed by DSC instrument, and static contact angle was measured by reflecting microscope. Change of IR peak and $T_g$ was conformed according to different epoxy mixing ratio. After fabrication of glass fiber/epoxy composites, tensile, compression, and flexural properties were tested by UTM by room and high temperature. The composites exhibited best mechanical properties when epoxy mixing ratio was 1:1.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.178-178
• /
• 2011

도로소음은 다양한 소음원에 의해 발생하며, 도로를 이용하는 사람과 도로 주변사람에게 큰 불편을 초래한다. 보다 쾌적한 환경을 원하는 현대인에게 있어 도로 소음의 경감은 중요한 환경 공해로 작용한다. 도로 소음을 줄이기 위해서는 여러 가지 방법이 있을 수 있으며, 이 중 도로 포장의 개선을 통해 도로 소음을 경감할 수 있으며, 이와 같은 포장을 저소음 포장이라고 한다. 저소음 포장은 주행하는 차량의 타이어와 노면이 마찰하면서 발생하는 소음을 최소화하기 위한 것으로 소음 발생의 메커니즘을 바탕으로 하고 있다. 저소음 포장중 가장 널리 사용되고 있는 방법은 공극을 늘리는 것이다. 약 20%의 공극은 타이어와 노면 사이의 에어펌핑음을 최소화 하며, 소리를 흡수하는 역할로 약 3dB의 소음 가소 효과가 있는 것으로 알려져 있다. 소음을 감소시키는 또 하나의 방법은 노면의 표면 조직을 매끈하게 하여 타이어와 노면의 충격음을 줄이는 방법이다. 노면의 평탄성을 개선하기 위해 포장에 사용되는 골재의 최대크기를 줄이는 소입경 포장을 소음 가소의 목적으로 유럽 등지에서 많이 사용되고 있다. 본 연구에서는 이와 같은 저소음 기능을 위해 공극률을 크게 하고 소입경 골재를 사용하는 소입경 저소음 포장의 현장 적용을 위한 배합 설계를 수행하였다. 소입경 저소음 포장의 최대 골재 크기는 현장 적용성과 경제성을 고려하여 10mm 골재를 사용하였으며, 수도권에서 입수한 4곳의 산지 골재를 분석하여 골재 합성 입도를 산정하였다. 10mm 저소음 포장의 골재 입도 범위는 공극률 15~18%를 목표로 하며, 이를 만족하기 위하여 배합 설계를 수행한 결과 5mm 통과 중량 백분율이 약 30%로 하는 개립도가 적당한 것으로 나타났다. 공극이 증가함에 따라 포장의 내구성 향상을 위해 사용된 고점도 바인더는 아스팔트 혼합물의 생산 및 시공온도를 증가시키게 된다. 또한 굵은골재의 비율이 높은 개립도 아스팔트 혼합물의 경우 운반과정과 포설 과정에서 온도가 빨리 떨어지는 단점이 있다. 이를 극복하기 위하여 중온 첨가제의 사용을 통해 생산 및 다짐온도를 낮추고자 하였다. 소입경 저소음 포장의 배합설계 과정은 배수성 포장의 배합설계 과정과 유사하나, 칸타브로 손실률과 흐름실험의 변곡점을 기준으로 할 경우, 칸타브로 손실률과 흐름 손실률이 매우 작아 변곡점을 판단하기 어렵기 때문에 칸타브로 손실률과 흐름 손실률의 기준 만족 여부로 판별하고, 최적 아스팔트 함량은 공극률을 기준으로 산정하는 것이 바람직할 것으로 판단된다. 중온 첨가제를 사용할 경우는 중온 첨가제로 인한 점도의 변화를 감안하여 혼합 및 다짐 온도를 결정하고 배합 설계를 수행하며, 중온 첨가제의 특성과 양에 따라 최적 아스팔트 함량이 변화하게 된다.

• 한국방재학회:학술대회논문집
• /
• 2011.02a
• /
• pp.197-197
• /
• 2011

최근 들어 전력 사용량의 증가로 인한 화력발전소의 부산물인 석탄회 중 바텀애시와 각종 공공사업과 관련하여 해마다 현장발생토의 발생량이 지속적으로 증가하고 있는 추세이다. 바텀애시와 현장발생토사를 효과적으로 재활용하는 방법 중 유동성 뒤채움재를 개발하여 활용하는 방안을 모색하기 위한 연구이다. SP로 분류된 흙 현장발생토와 서천 화력발전소에서 발생하는 석탄회 중 입경이 0.9~1.5mm의 바텀애시만을 선별하여 현장발생토와 바텀애시의 비율을 7 : 3으로 변환한 최적배합을 선정하여 강재로 제작된 가로 80cm, 세로 60cm, 높이 90cm의 모형토조를 이용하여 실험을 진행하였으며, 사용상 지하 매설이 되는 관의 거동 특성은 확인하기 위하여 내경 30cm, 두께 8mm의 연선관 중 하나인 PVC관을 원형지하매설관으로 선정하여 배합을 타설하는 과정과 타설 후 7일간의 양생기간을 거친 후 차량하중으로 가정할 수 있는 하중을 가하여 원형지하매설관의 관외부에서 수직방향과 수평방향의 토압과 관내부의 수직 수평방향 변위 그리고 관 자체의 횡 종단 변형을 측정하여 원형지하매설관의 거동특성을 파악하였다. 타설시 지하매설관은 유동성 뒤채움재의 특성으로 인하여 시간이 지남에 따라 안정화되는 것을 확인할 수 있었으며, 최대하중을 3300kgf로 하여 하중 재하 후 지하매설관의 거동특성은 대체적으로 일반 모래를 사용하여 실험한 값보다 적은 변형 특성을 보이고 있으나 수평토압의 경우 일반적인 흙의 변형과 전혀 상이한 결과값을 보이는 경우도 있어 추가적인 실험 및 고찰의 필요하다. 본 실험에서 사용한 최적배합비 이외의 배합으로 같은 실험을 수행하여 바텀애시 량의 가감 및 재활용 재료인 폐타이어 고무칩등을 첨가한 실험을 계획하고 있으며 추후 실내시험과 모형실험을 토대로 유한요소해석을 추가로 시행하여 실험값과 해석값의 비교를 할 예정이다.