• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6C
• /
• pp.251-258
• /
• 2009

In this study, the optimum design conditions for embankment construction on soft clay layer improved by soil compaction pile (SCP) are discussed by comparing the practical design method to the reliability design which is based on the loss function and advanced first order second moment (AFOSM) method. The results are summarized as follows; 1) the relationship between safety factor and failure probability becomes heavy exponentially, failure probability decreases rapidly till 1% approximately until safety factor is smaller than 1.2 and after then, failure probability decrease gradually along the increase of the safety factor. The design safety factor of 1.2 may be the critical value that has been established on considering both relationships appropriately, 2) the safety factor of 1.15 at the minimum expected total cost is a little smaller than the design safety factor of 1.2 and the failure probability is about 1%, 3) the sensitivities of the ratio of stress share and the internal friction angle of sand is larger than the variables related the undrained shear strength of soft layer. This result means that the distribution characteristic of n and ${\phi}$ influences on the stability analysis considerably and they should be considered necessarily on stability analysis of embankment on soft layer improved by SCP, 4) new failure points of the input variables at the design safety factor of 1.2(below failure probability of 0.1~0.3%) is far 1~2 times of standard deviation from the initial design values of themselves.

• The Journal of Engineering Geology
• /
• v.17 no.2 s.52
• /
• pp.289-297
• /
• 2007

Slope failure that is occurred by rainfall generates a lot of property damages and loss of lives. Slope stability management and reinforcement countermeasure can be attained through continuous monitoring about various slope types that adjoin in human's life for reducing slope failure from natural and artificial cut slope hazards. The study area is rock slope that is consisted of gneiss, and large scale joint set is ranging by fault activity. This rock mass is exposed during long period and has lithological weathering property of weathered rock or soft rock. In-situ investigation carried out after divide by natural slope and cut slope. As a result, the natural slope appeared to high possibility of planar failure and wedge failure in few joint points that main joint set is formed. On the other hand, slope failure conformation in cut slope was superior only wedge failure occurrence possibility in eight joint points. In result of numerical analysis using SLIDE 2D, the minimum safety factor was analyzed slope stability for cut slope relatively low than natural slope in this study.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.47 no.1
• /
• pp.49-56
• /
• 2019

Urban green spaces have been contributing to the improvement of environmental, mental, and physical health for humans. In addition, recent studies showed the potential role of vegetation in reducing the amount of crime in inner-city neighborhoods at the micro-scale level. However, little is known about the positive role of urban green areas in improving urban safety at the regional level. The purpose of this study is to examine the relationship between urban green areas and actual outdoor crime rates, while also considering socio-demographic factors. The study area is the city of Austin, Texas, USA, which consists of 506 block groups. This study utilized socio-demographic factors based on U.S. Census data and vegetation-related factors utilizing GIS and ENVI software. For analyses, the analysis of variance (ANOVA) and an ordinary least square (OLS) regression were utilized. The results from ANOVA showed that yearly crime rates per acre for areas having 0%~25% trees in their neighborhoods were 0.46% and 1.05% higher than those of having 25%~50% and >50% trees in the neighborhoods, respectively. The results from the OLS regression represented that income, NDVI and park rates in neighborhoods were negatively associated with the crime rate per acre, whereas the percentage of minorities and the percentage of teenage school dropouts were positively associated with the crime rate per acre. This study implies that urban green areas may help to improve the safety of urban areas.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.11
• /
• pp.5-16
• /
• 2008

Field monitoring data of nine sites were investigated to suggest an evaluation method on lateral movement of the quaywall on soft grounds. It was found that in order to evaluate the lateral movement of quaywalls with foundation piles such as the landing pier, the safety factor of slope should be applied with consideration of the stabilizing effect of the piles. If the required safety factor of slope is greater than 1.6 in slope stability analysis with consideration of the stabilizing effect of the piles, the quaywalls are considered to be safe against lateral movement. On the other hand, for the gravity-type quaywalls such as the caisson type quaywall, the required safety factor of slope should be greater than 1.3.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.169-169
• /
• 2010

박막형 CIGS 태양전지의 배면전극으로 사용되는 Mo 박막은 낮은 저항으로 인한 전기전도성과 열적 안전성이 아주 우수하다. 연구에서는 연성 CIGS 태양전지의 제조를 위한 Mo 배면전극의 대면적 증착기술에 관한 것으로 DC Magnetron Sputtering 공정을 이용하여 전주기술을 통한 Ni-Fe계 연성기판재 위에 졸걸법으로 합성된 $SiO_2$ 절연박막에 Mo 박막을 증착하는 것을 목적으로 하고 있다. 실험에서는 연성기판재 대신 시편을 Sodalime glass, Si wafer, SUS계 소재를 사용하여 스퍼터링 공정에 의한 Mo 박막을 증착하였다. 실험에서 타겟에 인가되는 전력과 공정압력을 변수로 하여 Mo 박막의 증착율, 전기저항성을 측정하였다. 타겟의 크기는 $80mm{\times}350mm$, 타겟과 기판간 거리 20cm 이었으며, 공정 압력은 2~50 mtorr 영역에서 인가전력을 0.5-1.5kW로 하였다. Mo 박막의 증착율과 전기적 특성을 측정하기 위하여 $\alpha$-step과 4-point probe(CMT-SR 1000N)를 이용하였다. 그리고 Mo 박막의 잔류응력을 측정하기 위하여 잔류응력측정기를 이용하였다. Mo 박막의 미세구조분석을 위하여 SEM 및 XRD를 분석을 실시하였다. 배면전극으로서 전기저항성은 공정압력에 따라 좌우 되었으며, 2 mTorr 공정압력과 1.5kW의 전력에서 최소값인 $8.2\;{\mu}{\Omega}-cm$의 저항값과 증착율 약 $6\;{\mu}/h$를 보였다. 기판재와의 밀착성과 관련한 잔류응력 측정과 XRD분석을 통한 결정립 크기를 분석하여 공정압력에 따른 Mo 박막의 잔류응력과 전기 저항 및 결정립 크기의 상관관계를 조사하였다. 그리고 대면적 CIGS 증착공정을 위해 직각형 타겟을 통해 증착된 Mo 박막의 증착분포를 20cm 이내 조사하였다.

• Journal of the Korean Geotechnical Society
• /
• v.15 no.5
• /
• pp.19-28
• /
• 1999

In this paper, an application of finite element procedure for the analysis of slope failure behavior has been studied. The most widely accepted methods in analyzing the slope stability problems are mostly based on limit equilibrium method. And the finite element method is widely accepted to analyze stress and displacements. This paper shows how the factor of safety calculated in the finite element method can be systematically incorporated into slope stability. In analyzing the slope failure behavior by finite element method, the effects of computational method and the results have been discussed. And several computations of slope stabilities were carried out to compare the finite element analysis results with those obtained by methods of slices based on the limit equilibrium analysis.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.3
• /
• pp.61-69
• /
• 2008

To examine the compression properties of structural members, the compression and bearing tests were conducted in parallel- and perpendicular-to-grain loading using domestic Japanese larch (Larix kaempferi (Lamb.) Carriere). Compression (bearing) properties with the length of a specimen and the contact length of the bearing plate were investigated, and deformations at each specimen length from the point of bearing force were measured to evaluate the effective end distance tabulated in the present practice (Korean Building Code). Compression (bearing) properties varied with the size of the bearing plate, and the end distance for dowel-type fastener taken into consideration of the specimen's deformation, for the safe design, should be applied with over 7 D.

• Journal of Food Hygiene and Safety
• /
• v.34 no.4
• /
• pp.348-353
• /
• 2019

This study was conducted to monitor the carbendazim residues in soybean and mungbean sprouts using LC-MS/MS method. Eighty-two samples were collected from markets in western Seoul. No carbendazim was detected in mungbean sprouts, however, it was detected in 6 among 59 soybean sprout samples showing a 10.2% of detection rate. Among these 6 carbendazim- detected soybean sprout samples, five exceeded the maximum residue limit presenting 83.3% of violation rate. The mean concentration in the detected samples was 0.063 mk/kg (0.012 ~ 0.104 mg/kg) and 5 of the 6 detected samples came from bulk sold products. None of the samples came from domestic products; three were from imported products and 3 were from unidentified sources. Risk assessment for the carbendazim from soybean sprout dietary intake was deemed safe and at less than 1 %Acceptable Daily Intake.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.21 no.1
• /
• pp.15-29
• /
• 2009

Most breakwater armor blocks are designed by using Hudson's or van der Meer's formula. The minimum weight of armor blocks is calculated by equating the resistance to the load in each formula. The larger value is then chosen as the design weight. In this study, we have performed reliability analyses for thus designed breakwater armor blocks of 12 trade harbors and 8 coastal harbors in Korea. The probability of failure calculated by the reliability analysis provides a criterion for evaluating the stability of armor blocks. The calculated probability of failure was almost same for all the breakwaters so that we were able to quantitatively evaluate the safety level of armor blocks of existing breakwaters. We also found that the safety factor used in the deterministic design method and the probability of failure in the reliability design method show a linear relationship. Therefore the probability of failure of existing breakwaters can be quantitatively calculated from the safety factors. The calculated probability of failure could also be used for determining the target probability of failure in the future.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.1A
• /
• pp.45-52
• /
• 2009

In conventional structural design, deterministic optimization which satisfies codified constraints is performed to ensure safety and maximize economical efficiency. However, uncertainties are inevitable due to the stochastic nature of structural materials and applied loads. Thus, deterministic optimization without considering these uncertainties could lead to unreliable design. Recently, there has been much research in reliability-based design optimization (RBDO) taking into consideration both the reliability and optimization. RBDO involves the evaluation of probabilistic constraint that can be estimated using the RIA (Reliability Index Approach) and the PMA(Performance Measure Approach). It is generally known that PMA is more stable and efficient than RIA. Despite the significant advancement in PMA, RBDO still requires large computation time for large-scale applications. In this paper, A new reliability-based design optimization (RBDO) method is presented to achieve the more stable and efficient algorithm. The idea of the new method is to integrate a response surface method (RSM) with PMA. For the approximation of a limit state equation, the moving least squares (MLS) method is used. Through a mathematical example and ten-bar truss problem, the proposed method shows better convergence and efficiency than other approaches.