• Korean Journal of Optics and Photonics
• /
• v.6 no.1
• /
• pp.33-38
• /
• 1995

We have measured the excited state absorption in $Ce:YAlO_{3}$, crystals for the first time and assigned it for a 5d$\rightarrow$conduction band transition. Two broad absorption bands were observed at 555 nm and 465 nm fowllowing the 308 nm XeCl laser excitation and their cross sections and oscillator strengths were calculated. We have also measured the fluorescence lifetimes in between 300 K and 700 K to study the nonradiative relaxation from the lowest 5d state of $Ce^{3+}$ ions and explained ESA and the transition process from the state in terms of a configurational coordinate.dinate.

• Magazine of the Korea Concrete Institute
• /
• v.11 no.1
• /
• pp.129-139
• /
• 1999

Recently, many strengthening methods are developed and used to rehabilitate existing structures. One of the old and popular methods is strengthening with bonding steel plate. However, steel plate bonding method has a defect, which is debonding failure of steel plate before yielding of the plate due to stress concentration at the of the bonded plate. The objective of this study is the experimental verification of the improved bonding properties of a strengthening plate with notches. Two normal beams and ten strengthened beams with steel plate, which have several different notches, are tested and showed their effectiveness. Test results show that the notches of strengthening plate significantly improve post-yielding behavior, compared to normally strengthened beams. It is proved that the notches of strengthening plate increases ultimate strength 14% more than normal strengthened beam after yield strength. As for the shape of notches, arc notch is the best. and triangle notch and trapezoidal notch are the next and end welding method has no effect.

• Journal of the Korean Data and Information Science Society
• /
• v.25 no.2
• /
• pp.393-402
• /
• 2014

The simplest and the most important distribution in survival analysis is the exponential distribution. In this paper, we investigate the influence of the random censorship model on the estimation of the scale parameter of the exponential distribution. The considered random censorship models are Koziol-Green model and the generalized exponential distribution model. Two models have different meanings. Through the simulation study, the averages of the estimated values of the parameter do not show big differences, however the MSE of the estimator tends to be bigger when the supposed model is significantly different from the true model.

• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.6
• /
• pp.806-815
• /
• 2010

Gear trains are combined with the planetary gear units and helical gear units. It is known that the combination type is decisive to the system performances of the transmissions. In this paper, within the commonly used range of the design requirements for medium and large scaled (1~8 MW) wind turbines, the transmission characteristics of the typical layouts of the gear train are investigated. According to the international standard by ANSI/AGMA/AWEA 6006-A03, the gear boxes are basically designed and compared with respect to the system lifes of 99% reliability, total weight, the power densities, overall diameter/length and the maximum stresses of the gear teeth. With these comparison works, the characteristics of the layouts of gear trains are discussed.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.1
• /
• pp.36-41
• /
• 2010

In oder to operate sensor networks effectively it is very important to use the energy in the individual nodes efficiently and so increase their lifetime. Cluster-based routing algorithms such as LEACH and HEED obtain the efficiency of energy using data transfer between cluster heads and its members. In this paper we analyze the typical cluster-based routing algorithms and suggest a new energy efficient method of electing the cluster heads with the maximum delay of dead nodes occurrence. The efficiency of the proposed algorithm is verified through MATLAB simulation.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.55 no.2
• /
• pp.89-97
• /
• 2006

Interior permanent magnet synchronous motor(IPMSM) has become a popular choice in electric vehicle applications, due to their excellent power to weight ratio. The paper is proposed maximum torque control of IPMSM drive using learning mechanism-fuzzy neural network(LM-FNN) controller and artificial neural network(ANN). The control method is applicable over the entire speed range and considered the limits of the inverter's current and voltage rated value. For each control mode, a condition that determines the optimal d-axis current $i_{d}$ for maximum torque operation is derived. This paper considers the design and implementation of novel technique of high performance speed control for IPMSM using LM-FNN controller and ANN controller. The hybrid combination of neural network and fuzzy control will produce a powerful representation flexibility and numerical processing capability. Also, this paper is proposed speed control of IPMSM using LM-FNN and estimation of speed using ANN controller. The back propagation neural network technique is used to provide a real time adaptive estimation of the motor speed. The proposed control algorithm is applied to IPMSM drive system controlled LM-FNN and ANN controller, the operating characteristics controlled by maximum torque control are examined in detail. Also, this paper is proposed the analysis results to verify the effectiveness of the LM-FNN and ANN controller.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.6C
• /
• pp.603-613
• /
• 2006

Low-power design is one of the most important challenges encountered in maximizing battery life in portable devices as well as saving energy during system operation. In this paper we propose a low-power DCT (Discrete Cosine Transform) architecture using a modified Computation Sharing Multiplication (CSHM). The overall rate of Power consumption is reduced during DCT: the proposed architecture does not perform arithmetic operations on unnecessary bits during the Computation Sharing Multiplication calculations. Experimental results show that it is possible to reduce power dissipation up to about $7\sim8%$ without compromising the final DCT results. The proposed low-power DCT architecture can be applied to consumer electronics as well as portable multimedia systems requiring high throughput and low-power.

• 한국IT서비스학회:학술대회논문집
• /
• 2009.11a
• /
• pp.321-326
• /
• 2009

원자력발전 산업은 국내 최대의 전력공급원으로서 '09년 현재 20기의 원전이 가동 중에 있고 8기의 원전이 건설 중이다. 또한 수출주도형 독자노형 개발을 목적으로 한 원전 설계 개발 사업도 진행되고 있다. 국가 기반산업이기도 한 원자력 산업에는 다양한 정보관리시스템들이 운영되고 있으며 지속적인 개선이 이루어지고 있다. 원자력발전소는 60년에 이르는 긴 수명주기를 가지고 있기 때문에 설계 단계에서부터 생산되는 정보를 관리할 수 있는 체계적인 방법이 필요하며, 산업 특성상 다양한 참여기관들이 상호 협업을 진행할 수 있는 통합 창구 역할의 시스템이 요구되고 있다. 본 연구에서는 원자력발전소의 정보관리시스템 개발을 위해 신규원전 사업자에게 요구되는 EPRI URD 요건 및 실제 원전 설계개발 사업에서의 시스템 요구사항 등을 분석하여, 원자력발전소의 원전 정보관리시스템 개발요건을 도출하였으며 ISO 10303 국제표준 기술을 활용한 일부 시스템 프로토타입 구현을 통한 예비 타당성 평가를 수행하였다. 본 연구를 통해 국내 원전 산업에 국제표준 도입 가능성은 확인하였으나, 국제표준 개발이 아직 진행 중인 점을 고려할 때 실제 원전 적용을 위해서는 향후 추가 연구가 필요하다.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.3
• /
• pp.155-161
• /
• 2015

Efficient energy consumption is a one of the key issues in wireless sensor networks. Clustering-based routing algorithms have been popular solutions for such an issue. Re-clustering is necessary for avoiding early energy drain of cluster head nodes in such routing strategies. The re-clustering process itself, however, is another source of energy consumption. It is suggested in this work to adaptively set the frequency of re-clustering by comparing the energy levels of cluster heads and a threshold value. The algorithm keeps the clusters if all the cluster heads' energy levels are greater than the threshold value. We confirm through simulations that the suggested algorithm shows better energy efficiency than the existing solutions.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.21 no.1
• /
• pp.4-22
• /
• 2012

치경부에 발생된 병소 부위(cervical lesion)는 "우식성 병소(caries lesion)"와 "비우식성 병소(non-caries lesion)"로 분류할 수 있다. 우식성 병소는 구강 내 세균들의 활동에 기인하여 발생된 병소로서 경조직 손상 부위의 수복과 함께 우식이 재발하지 않도록 체계적으로 대응하는 것이 필요하다. 비우식성 병소는 산성 물질, 저작력 및 이물질에 의한 마모 작용과 같은 다양한 원인에 의해 발생될 수 있으며, 수복 치료에 앞서 병소에 발생 원인을 규명하는 것이 중요하다. 먼저 병소 유발 원인에 대한 분석과 이에 대한 적절한 조치를 취한 후에 수복 치료를 시행하는 것이 바람직하다. 심미적인 요구가 높은 치경부 병소의 수복을 위하여 사용될 수 있는 재료는 "불소를 방출하는 재료"와 "불소를 방출하지 않는 재료"로 나뉘어지는데, 세균의 활동에 의해 형성된 우식성 병소의 수복에는 불소를 방출하는 재료를 사용하는 것이 추천된다. 우수한 심미성과 보다 강력한 유지력이 요구되는 경우에는 복합 레진계 수복 재료들을 사용하여 수복하게 되는데, 이 경우에는 "접착 술식(bonding procedure)"이 중요한 역할을 수행하게 된다. "접착 술식"은 수복물의 일차적인 유지 뿐 아니라 지각과민을 해소하고 2차 우식을 방지하며, 궁극적으로 수복물의 수명을 좌우하는 결정적인 역할을 수행한다. 자연 치아를 최대한 보존하고자 하는 "최소침습(minimum intervention)" 개념에 바탕을 두고 세심하게 형성된 와동에 각각의 증례에 최적화된 수복 재료를 선택하여 수복치료를 시행한다면 보다 심미적이고 환자가 편안한 치경부 수복물을 완성할 수 있을 것이다.